Body (Interior / Exterior / Electrical)

Floor Console

33steps
~198min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 33

Contents:

Floor Console Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the floor console upper cover. (Refer to Floor Console - "Floor Console Upper Cover")
  2. Remove the console tray cover (A).
    Clip position :
  3. Remove the bolts (A).

    Tightening torque : 6.9 - 9,8 N·m

    [Console Mounting Bracket's Side] [Console Rear Mounting Bracket's Side] [Driver's Side] [Passenger's Side]
  4. Remove the floor console assembly (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Floor Console Assembly Disassembly and Reassembly

Disassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Rear Console Cover
  1. Remove the rear console upper garnish (A).
    Clip position :
  2. Remove the cover (A) after removing the screws.
    Clip position :
  3. Remove the rear console cover.
  4. Remove the console armrest (A) after removing the screws.
  5. Remove the console armrest.
  6. Remove the floor console assembly. (Refer to Floor Console - "Floor Console Assembly")
  7. Remove the floor console storage box (A) after removing the screws.
  8. Remove the floor console lower garnish (A) after removing the screws.
  9. Remove the floor console wiring (A) after removing the fasteners.
    Clip position :
  10. Remove the tray (A) after removing the screws.
Console Armrest Console Tray

Reassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Reassemble in the reverse order of disassembly.

Floor Console Switch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the floor console switch. (Refer to Floor Console - "Floor Console Upper Cover")

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Floor Console Upper Cover Removal and Installation

Removal

  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the rear console upper garnish (A).
    Clip position :
  3. Remove the storage box garnish (A).
  4. Remove the console upper cover (A).
  5. Disconnect the floor console extension wiring (A) after removing the fastener.
    Clip position :
  6. Disconnect the connector (A, B, C, D ,E ,F ,G ,H). A : WPC connector B : WPC lamp connector C : Driver parking assistance switch connector D : SBW connector E : SBW lamp connector F : Fingerprint recognition unit connector G : Floor console switch H : SSB connector

Installation

  1. Install in the reverse order of removal.

Floor Console Upper Cover Disassembly and Reassembly

Disassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the dial type SBW. (Refer to Motor and Reduction Gear System - "SBW(Shift By Wire) Lever")
  2. Remove the console upper center cover (A).
    Clip position :
  3. Remove the passenger side garnish after removing the screws.
    Clip position :
  4. Disconnect the button engine start switch connector (A).
  5. Remove the button start switch garnish (A) after removing the screws.
    Clip position :
  6. Remove the button start switch (A) after removing the screws.
  7. Remove the driver side garnish (A) after removing the screws.
  8. Remove the console switch (A) after removing the screws.
    Clip position :
  9. Remove the fingerprint recognition unit (A) after removing the screws.
  10. Remove the wireless charging unit (WPC) (A) after removing the screws.
    Clip position :

Reassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Reassemble in the reverse order of disassembly.

Front Console Cover Removal and Installation

Removal

  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Separate the front console cover (A) after removing the fasteners.
    Clip position :
  3. Remove the front console cover (A) after disconnecting the connectors (B).

Installation

  1. Install in the reverse order of removal.