Body (Interior / Exterior / Electrical)

Sunroof

51steps
~306min
4/5difficulty
010203040505.94N·mlb·ft
Tightening torque found on this page
Done 0 of 51

Contents:

Components and Components Location

Component and Component Location

Wide Sunroof
1. Front Glass
2. Front Glass Weatherstrip
3. Moving Glass
4. Sunroof Deflector
5. Sunroof Rail Assembly
6. Sunroof Drive Unit
7. Sunroof Roller Blind
8. Moving Glass Motor
9. Roller Blind Motor
10. Sunroof Cable
11. Sunroof Frame

Troubleshooting

Troubleshooting

Water Leaks
Components Suspected Cause Correction
Movable Glass Defect of gap/flush Adjustment
Weatherstrip Incorrect installation and deformation Replacement

Wind Noise
Components Suspected Cause Correction
Deflector Deformation and separation Replace or reinstall
Movable Glass Defect of gap/flush Adjust of gap/flush

Drive Noise
Components Suspected Cause Correction
Weatherstrip Rubbing noise apply the silicone oil
Hardware Loose or unfastened Hardware re-tighten
Cover / Trims Interference noise (rattle/rubbing) Attach the pad to the noise generating area.

Operation Noise
Components Suspected Cause Correction
Mechanism rail Foreign matters in the mechanism rail Cleaning the rail and apply the grease
Motor Defective coupling of mechanism cable and motor pinion gear Adjust or replace the motor position
Motor pinion gear worn out or broken Replacement
Roller Blind Noise inside the spring Replacement

Malfunctions
Components Suspected Cause Correction
Mechanism rail Increased operating load due to accumulation of foreign matters 1. Cleaning the rail and apply the grease
2. Adjust or replace the motor position
3. Replacement of mechanism rail
Motor Defective coupling of mechanism cable and motor pinion gear Adjust or replace the motor position
Motor position loss and sunroof switch one-touch operation failure due to discharge and replacement of battery and fuse Motor Initialization
Roller Blind Separation of the teflon guide Replace or reinstall
Release of the spring tension Replacement

On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The Roof Controller Module (RCM) can be quickly diagnosed for problems with KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details

Adjustment

Adjustment

Glass Adjustment
  1. Check the gap and flush of the front glass (A) and moving glass (B).
    Front Glass - Moving Glass Gap (mm) Height (mm)
    5.6 - 5.8 -1 to 0
  2. Open the moving glass completely by pressing the wide sunroof switch.
  3. Remove the decoration cover (A).
  4. If it is necessary to adjust the glass, slightly loosen the glass height adjustment screws (A) and tighten the screws.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    [Inside] [Outside]
  5. POWER ON or start the vehicle.
  6. Close the sunroof completely if opened
  7. Release the sunroof control lever.
  8. With the sunroof glass or roller blind closed, lightly press the switch forward until it moves once, then release your hand.
  9. Keep pressing the sunroof switch forward until the sunroof glass or roller blind opens and closes completely.
    • Do not release the lever until the operation is completed.
    • If you release the switch during operation, it will try again from the beginning.
  10. Release the sunroof control lever after all operation has completed. (The sunroof system been reset.)
Initialize Sunroof If necessary, initialize the sunroof according to the initialization method. The sunroof and roller blind are initialized using the sunroof switch.

Motor Removal and Installation

Replacement

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the roof trim assembly. (Refer to Roof Trim - "Roof Trim Assembly")
  2. Remove the sunroof motor (B) by removing the screws after disconnecting the connector (A). [Roller Blind Motor] [Moving Glass Motor]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the sunroof reset procedure.
    1. POWER ON or start the vehicle.
    2. Close the sunroof completely if opened
    3. Release the sunroof control lever.
    4. With the sunroof glass or roller blind closed, lightly press the switch forward until it moves once, then release your hand.
    5. Keep pressing the sunroof switch forward until the sunroof glass or roller blind opens and closes completely.
      • Do not release the lever until the operation is completed.
      • If you release the switch during operation, it will try again from the beginning.
    6. Release the sunroof control lever after all operation has completed. (The sunroof system been reset.)
  3. When replacing the roof control module (RCM) or motor, perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Sunroof Assembly Removal and Installation ➤

Sunroof Deflector Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Press the sunroof switch to fully open the sunroof glass.
  2. Separate the sunroof deflector (A) after removing the screws.
  3. Remove the deflector.
    1. Push the deflector mounting bracket (B) up in the direction of the arrow.
    2. Remove the deflector (A) after pulling the deflector mounting bracket (B) in the direction of the arrow.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Sunroof Glass Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Moving Glass
  1. Open the moving glass completely by pressing the wide sunroof switch.
  2. Remove the decoration cover (A).
  3. Remove the screws (A).
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    [Inside] [Outside]
  4. Remove the glass (A).
Front Glass
  • To remove the front glass, use the tools shown in the following figure.
[Tool Diagram] Square wire
Insert-type wire grip
  • Insert and fix the square wire into the hole of the wire grip .
[Tool Assembly Diagram]
  1. Remove the roof side molding. (Refer to Body Side Molding - "Roof Side Molding")
  2. Fully open the moving glass by pressing the wide sunroof switch.
  3. Cut the sealant by applying force in the direction of the arrow while pulling the square wire (A) to the left and right.
    • Be careful as the wire may break when working.
    • Be careful not to damage the body surface.
    • When installing the windshield, if the length of the wire is longer, a lot of force is applied, so divide the sections and in half and cut the sealant.
  4. Remove the front glass carefully so that it does not get damaged.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Moving Glass
  1. Install in the reverse order of removal.
Front Glass
To install the front glass, use the tools shown in the following figure. [Tool Diagram] Sealant nozzle
Adhesive sealant for car glass
Sealant gun
Primer
Primer application brush
  1. Cut off the remaining sealant (A) around the wide sunroof frame windshield installing surface after using a knife blade.
    • When cutting off the remaining sealant of the frame, leave it 2 mm thick on the working surface and cut.
    • Be careful not to damage the frame painted surface.
    • If the body painting surface is damaged, apply the repair paint or anti-corrosion agent.
  2. Wipe the edge of the wide sunroof frame and front glass with alcohol or blow with an air gun to clean it.
  3. Apply the primer around the wide sunroof frame.
  4. After applying the primer, apply the sealant (B) around the wide sunroof frame (A).
    Be careful not to leak or break the sealant when applying the sealant by using a sealant gun.
  5. Attach the front glass (A) to the wide sunroof frame.
  6. Install the front glass completely after checking the flush and gap.
    Item Gap [mm (in.)] Flush [mm (in.)]
    Windshield glass - Front glass 55 - 57 (2.16 - 2.24) 0.5 - 2.5 (0.2 - 1.0)
    Front glass - Moving glass 56 - 58 (2.2 - 2.28) 0.5 - 1 (0.2 - 0.4)

    [Windshield glass - Front glass] [Front glass - Moving glass]
  7. Tape around the front glass so that it does not float.
    • If the sealant is over-applied and the sealant is visible outside the vehicle, clean it with alcohol or a cleaning agent.
    • After installing the front glass, leave the vehicle on level ground at least for 4 hours.
    • If the vehicle needs to be used, drive slowly at least for 8 hours.
    • The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.

Sunroof Mechanism Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the moving glass. (Refer to Sunroof - "Sunroof Glass")
  2. Remove the moving glass motor and roller blind motor. (Refer to Sunroof - "Motor")
  3. Disconnect the sunroof connector (A) after removing the fastener.
  4. Remove the sunroof mechanism after removing the screw (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Sunroof Roller Blind Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the sunroof assembly. (Refer to Sunroof - "Sunroof Assembly")
  2. Remove the roller blind bracket (A) after removing the screws.
  3. Remove the roller blind bar.
    1. Pull the roller blind bar (A) in the direction of the arrow .
    2. Separate the roller blind bar (A) by rotating it in the direction of the arrow .
  4. Remove the roller blind assembly (A) after removing the screws.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Sunroof Switch Inspection

Inspection

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the overhead console lamp. (Refer to Light & Vision System - "Overhead Console Lamp")
  2. Check for continuity between the terminals.
    Open 1st Open 2nd Close 1st Close 2nd Tilt up Tilt down
    Signal
    (Pin No.)
    Manual open Auto Open Manual close Auto Close
    Signal A
    (4)
    O O
    Signal B
    (5)
    O O O
    Signal C
    (6)
    O O O
    Ground
    (1)
    O O O O O O

Sunroof Weatherstrip Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Frame Weatherstrip
  1. Remove the moving glass. (Refer to Sunroof - "Sunroof Glass")
  2. Remove the weatherstrip (A).
  3. Fully open the moving glass.
  4. Remove the weatherstrip (A).
Front Glass Weatherstrip

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Frame Weatherstrip
  1. After removing the double-sided tape remaining on the wide sunroof frame, apply the primer [81685-3S000].
  2. After installing the frame weather strip, press the installing area.
  3. Install the moving glass. (Refer to Sunroof - "Sunroof Glass")
    • Place the air vent hole (A) in the rear part, and install it in the order of front part → side part → rear part.
    • Since the cross-section is not symmetrical, check the inside and outside and then install the frame weatherstrip.
    • Since the frame weatherstrip cannot be reused, it must be replaced with a new one when removed or replaced.
  4. Install in the reverse order of removal.
    Be careful not to install the weatherstrip in reverse by referring to the cross-section below.
Front Glass Weatherstrip