Body (Interior / Exterior / Electrical)

Front Door

64steps
~384min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 64

Contents:

Components and Components Location

Component and Component Location

Front Door [Trim]
1. Front Door Trim
2. Front Door Inside Handle
3. Main Power Window Switch
4. Sub Power Window Switch
5. Front Door Belt Inside Weatherstrip
6. Front Door Belt Outside Weatherstrip
7. Front Door Frame Molding
8. Front Door Frame Garnish
9. Front Door Body Side Weatherstrip
10. Front Door Side Weatherstrip.

Front Door [Mechanism]
1. Front Door Module
1-a. 8.8 - 11,8 N·m
2. Front Door Latch
2-a. 6.9 - 10,8 N·m
3. Front Door Speaker
4. Front Door Window Glass
4-a. 8.8 - 11,8 N·m
5. Front Door Glass Run
6. Front Door Latch
6-a. 6.9 - 10,8 N·m
7. Front Door Outside Handle
7-a. 3.4 - 5,7 N·m (0.35 - 0.58 kgf·m, 2.5 - 4.2 lb·ft, 30.4 - 50.3 lb·in)

Adjustment

Adjustment

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Adjustment
  1. Check that the gap between the door and the body is even after parking in a flat level.
  2. Loosen the door hinge (A) bolts (B), adjust the door (C) by moving it back and forth, left and right, and then tighten the bolts.

    Tightening torque : 21.6 - 26 N·m

  3. Check that the gap between the door and the body is even.
  4. Loosen the screws (B) and adjust the striker (A) by moving it back and forth, left and right, and then tighten the screws.

    Tightening torque : 18.6 - 33 N·m

  5. Check that the door opens and closes properly.
Striker Adjustment Glass Adjustment
Check the damage of the glass run and channel and replace them if necessary.
  1. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  2. Adjust the gap by moving the window glass (A) up, down, left and right, and then tighten the bolts.

    Tightening torque : 8.8 - 11,8 N·m

  3. Check the window glass for normal operation.
  4. With the window open, use the auto/manual up switch to completely close the window and keep it closed for more than 0.2 seconds. (If you operate the up switch while the window is completely closed, it will not be initialized)
Window Motor Reset

On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The front door can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details
  2. The motor can continuously operate at least 15 strokes, and it can be operated again 30 to 40 seconds after the motor stops due to the overheat protection function.
Protection of Window Motor Overheating

Front Door Garnish and Molding Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Frame Molding
  1. Remove the molding (A).
    Clip position :
  2. Remove the garnish (A).
    Clip position :
Door Frame Garnish

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Handle Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Inside Handle
  1. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  2. Remove the handle (A) after removing the screws.
  3. Remove the front door module. (Refer to Front Door - "Front Door Module")
  4. Remove the bolt (A).

    Tightening torque : 8.8 - 11,8 N·m

  5. Remove the door lock assembly (A) by pulling it in the direction of the arrow.
  6. Disconnect the handle connector (A).
  7. Separate the handle wiring (A).
    Clip position :
  8. Separate the latch rod (A).
    Clip position :
  9. Remove the handle (A) after removing the nuts.

    Tightening torque : 3.4 - 5,7 N·m

Door Outside Handle

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Latch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door module. (Refer to Front Door - "Front Door Module")
  2. Disconnect the outside handle connector (A).
  3. Separate the outside handle wiring (A).
    Clip position :
  4. Remove the screws (A).

    Tightening torque : 6.9 - 10,8 N·m

  5. Remove the latch (B) after separating the latch rod (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Latch Inspection

Inspection

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door latch. (Refer to Front Door - "Front Door Latch")
  2. Apply voltage to connector terminal and check that the door latch operates properly.
    Location Terminal
    Driver 7, 8
    Passenger 1, 2

Front Door Module Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door window glass. (Refer to Front Door - "Front Door Window Glass")
  2. Disconnect the door main wiring connector (A).
  3. Disconnect the outside mirror connector (A).
  4. Separate the door module (A) after removing the bolts.

    Tightening torque : 8.8 - 11,8 N·m

  5. Remove the door module after disconnecting the wiring connectors (A).
  6. Separate the wiring harness (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Speaker Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Speaker
  1. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  2. Separate the speaker connector (A).
  3. Remove the speaker (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Switch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Window Main Switch
  1. Remove the front door trim. [Driver's side] (Refer to Front Door - "Front Door Trim")
  2. Remove the switch (A) by pulling the hook in the direction of the arrow.
  3. Remove the passenger's side front door trim. (Refer to Front Door - "Front Door Trim")
  4. Remove the switch (A) by pulling the hook in the direction of the arrow.
Power Window Sub Switch

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Separate the quadrant inner cover (A).
  3. Remove the quadrant inner cover (A) after disconnecting the tweeter speaker connector.
  4. Separate the door trim (A) after removing the screw.
    Clip position :
  5. Remove the door trim after disconnecting the connectors (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Weatherstrip Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Side Weatherstrip
  1. Separate the door checker (A) after removing the bolt.

    Tightening torque : 21.6 - 32 N·m

  2. Remove the weatherstrip (A).
  3. Remove the weatherstrip (A).
  4. Remove the weatherstrip (A).
  5. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  6. Remove the weatherstrip (A).
Door Body Side Weatherstrip Door Belt Outside Weatherstrip Door Belt Inside Weatherstrip

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Window Glass Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Window Glass
  1. Remove the front door belt inside and outside weatherstrips. (Refer to Front Door - "Front Door Weatherstrip")
  2. Lower it until window glass bolt is exposed in the hold plug by operating the power window switch.
  3. remove the window glass (A) after removing the bolts.

    Tightening torque : 8.8 - 11,8 N·m

  4. Remove the door window glass.
  5. Remove the front door frame garnish and molding. (Refer to Front Door - "Front Door Frame Garnsih and Moilding")
  6. Remove the glass run (A).
Door Window Glass Run

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Door Window Motor Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Power Window Motor
  1. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  2. Remove the motor connector (A).
  3. Remove the motor (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the window motor reset procedure. (Refer to Front Door - "Adjustment")