Body (Interior / Exterior / Electrical)

Front End Module

22steps
~132min
4/5difficulty
0102030405026.520N·mlb·ft
Tightening torque found on this page
Done 0 of 22

Contents:

Carrier Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Recover refrigerant by using the refrigerant recovery/recycling/charging machine. (Heating,Ventilation And Air Conditioning - "Refrigerant Recovery/Recycling/Charging/Vacuum/Leak Test")
  2. Remove the condenser. (Refer to Heating,Ventilation And Air Conditioning - "Condenser")
  3. Remove the radiator. (Refer to Cooling System - "Radiator")
  4. Remove the hood latch. (Refer to Hood - "Hood Latch")
  5. Remove the buzzer. (Refer to Security & Vehicle Ignition System - "Smart Key")
  6. Disconnect the headlamp connector (A).
  7. Disconnect the hood latch cable and high temperature radiator upper cooling hose (A).
    Clip position :
  8. Disconnect the front end module wiring connector (A).
    Clip position :
  9. Remove the carrier assembly (A) after removing the bolts.

    Tightening torque : 21.6 - 26 N·m

  10. Remove the horn. (Refer to Front End Module - "Horn")
  11. Separate the front end module wiring (A) from the carrier assembly.
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Bumper Beam Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.

Front Bumper Beam Assembly

  1. Remove the front radar. (Refer to Advanced Driver Assistance System (ADAS) - "Front Radar")
  2. Remove the virtual engine sound system unit (VESS). (Refer to Driver & Driving Assistance System - "Virtual Engine Sound System (VESS)")
  3. Remove the front bumper beam assembly (A) after removing the bolts and nuts.

    Tightening torque : 22.6 - 26 N·m

Front Bumper Stiffener

  1. Remove the front bumper assembly. (Refer to Front & Rear Bumper - "Front Bumper Assembly")
  2. Remove the front bumper stiffener (A) after removing the bolts.

    Tightening torque : 22.6 - 26 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
    Installation/calibration is required when reinstalled after the front radar is removed. (Refer to Advanced Driver Assistance System (ADAS) - "Front Radar")

Horn Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
[Low pitch]
  1. Remove the headlamp. (Refer to Light & Vision System - "Headlamp")
  2. Disconnect the horn connector (A).
  3. Remove the horn (A) after removing the bolt.

    Tightening torque : 7.8 - 11,8 N·m

  4. Remove the headlamp. (Refer to Light & Vision System - "Headlamp")
  5. Disconnect the horn connector (A).
  6. Remove the horn (A) after removing the bolt.

    Tightening torque : 7.8 - 11,8 N·m

[High pitch]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.