In this manual: Body (Interior / Exterior / Electrical)
63steps
~378min
4/5difficulty
Tightening torque found on this page
Done 0 of 63
Contents:
Cowl Top Cover Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Remove the front trunk. (Refer to Body Side Molding - "Front Trunk")
Remove the front wiper arm. (Refer to Exterior Green House - "Wiper Arm")
Separate the washer nozzle (A).
Remove the cowl top cover (A) after removing the fasteners.
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Remove the tailgate trim. (Refer to Tailgate - "Tailgate Trim")
Remove the rear spoiler. (Refer to Body Side Molding - "Rear Spoiler")
Remove the tailgate garnish. (Refer to Body Side Molding - "Tailgate Garnish")
Disconnect the heated wire connector (A).
Insert the piano wire (A) in the corner side.
Cut off the sealant of forward edge side (B) in pulling a piano wire (A) left and right.
Be careful not to burn hands as the excessive heat may be generated while using the wire.
Be careful as the wire may break when working.
Remove the tailgate glass (A) carefully using a glass holder (B).
Tailgate Glass Installation
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Clean the edges of the body panel and the tailgate glass with alcohol, etc.
Apply a body primer to the edge of the body panel.
Be careful not to touch the primed surface with your hands, as water leakage may occur after the tailgate glass is installed.
Do not apply the glass primer to the body.
Do not smear the primer-covered surface to any foreign materials.
Apply the glass primer to the edge of tailgate glass.
Be careful not to touch the primed surface with your hands, as water leakage may occur after the tailgate glass is installed.
Do not smear the primer-covered surface to any foreign materials.
Apply the sealant (B) around the tailgate glass (A) by using a sealant gun.
Using the glass holder, adjust the tailgate glass (A) to stopper hole (B) on the body and carefully tap the tailgate glass to make the edges fully seated on the bonding surface of body.
Connect the tailgate heated wire connector (A).
Perform a water leak test at least 3 to 4 hours later after installing the tailgate glass.
Keep the water stream away from directly touching the newly installed adhesive surface and let the water fall on the side of the glass.
If a leak occurs, apply the sealant to the area where the leak occurs.
Leave the car on a flat surface for at least 4 hours after installing the tailgate glass. If driving the car is inevitable, drive at a low speed in least 8 hours.
The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.
Install in the reverse order of removal.
Windshield Glass Removal
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Remove the front pillar trim. (Refer to Interior Trim - "Front Pillar Trim")
Remove the inside mirror assembly. (Refer to Mirror - "Inside Mirror")
Remove the auto defogging sensor. (Refer to Heater and Air Conditioning Unit - "Auto Defogging Sensor")
Remove the rain sensor. (Refer to Exterior Green House - "Rain Sensor")
Remove the hi-pass antenna. (Refer to Infotainment system - "Antenna")
Remove the front view camera unit. (Refer to Advanced Driver Assistance Systems (ADAS) - "Front Camera")
Remove the cowl top cover. (Refer to Exterior Green House - "Cowl Top Cover")
Remove the A pillar garnish. (Refer to Body Side Molding - "A Pillar Garnish")
Insert the piano wire (A) in the corner side.
While pulling the piano wire (A) in the direction of the arrow, cut out the sealant on the front edge side (B).
Be careful not to burn hands as the excessive heat may be generated while using the wire.
Be careful as the wire may break when working.
Cut off the sealant on (A-A), (B-B) area, while pulling the piano wire to the left and right.
Cut the sealant in section (A-A) using a cutter knife.
Cut the sealant carefully as it may damage the crash pad when working the area (A-A). Be careful not to damage the body painting surface.
When using a cutter knife, use the blade of a knife with a 20 to 30 cm-long.
Remove the windshield glass (A) carefully by using a glass holder (B).
Windshield Glass Installation
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
When replacing with the windshield glass of the front camera type, be sure to replace with the type equipped with the coupler. If the coupler is attached to the windshield glass type that is not equipped with the coupler, the front camera may not work properly.
Cut off the sealant around the body panel by using a cutter knife, leaving a thickness of 2 mm from the adhesive side. When a new windshield is used, put the matching marks on the glass and the body.
Be careful not to damage the body surface.
If the body painting surface is damaged, apply the repair paint or anti-corrosion agent.
Clean the edges of the body panel and the windshield glass with alcohol, etc.
Apply a body primer to the edge of the body panel.
Do not touch the primed surface with your hands, as water leakage may occur after the windshield glass is installed.
Do not apply the glass primer to the body.
Do not smear the primer-covered surface to any foreign materials.
Apply the glass primer to the edge of windshield glass.
Do not touch the primed surface with your hands, as water leakage may occur after the windshield glass is installed.
Do not apply the glass primer to the body.
Do not smear the primer-covered surface to any foreign materials.
Apply the sealant within 5 minutes after applying the primer.
Apply the sealant (B) around the windshield glass (A).
Sealant bead width Height : 12 mm (0.47 in.) Width : 8 mm (0.31 in.)
Adjust the windshield glass (A) to stopper hole (B) of the body by using glass holder and carefully tap the windshield glass and press it against the body flange surface.
Test for water leakage.
Keep the water stream away from directly touching the newly installed adhesive surface and let the water fall on the side of the glass.
If water leak occurs, apply sealant to the leaked area.
Leave the car on a flat surface for at least 4 hours after installing the windshield glass.
If the vehicle needs to be used, drive slowly at least for 8 hours.
The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.
Install in the reverse order of removal.
Wiper Arm Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Wiper Arm
Remove the wiper arms (A) by removing the nuts after removing the caps.
Tightening torque : 22.6 - 26 N·m
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
When installing, place the wiper arm to the specified position and then tighten the nut. [Front Wiper] (Passenger)
Place the wipers to the marking (A) position of cowl top cover.
(Driver Side)
Place the wipers to the marking (A) position of windshield glass.
Wiper Motor Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Wiper Motor
Remove the cowl top cover. (Refer to Exterior Green House - "Cowl Top Cover")
Disconnect the wiper motor connector (A).
Remove the wiper motor (A) after removing the bolts.
Tightening torque : 6.9 - 10,8 N·m
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
Wiper Washer Motor Removal and Installation
Removal
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Washer Motor
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
Open the front trunk (A).
Open the auxiliary 12 V battery service cover (A).
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed.
Remove the motor connector (A).
Remove the motor (A) in the direction of the arrow after disconnecting the washer nozzle hose (B).
Washer fluid is drained when removing washer motor.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
Open the front trunk (A).
Open the auxiliary 12 V battery service cover (A).
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed.
Disconnect the washer fluid level sensor connector (A).
Remove the washer level sensor (A) in the direction of the arrow.
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
Open the front trunk (A).
Open the auxiliary 12 V battery service cover (A).
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed.
Separate the washer nozzle hoses (A).
Disconnect the washer lever sensor connector (A) and washer motor connector (B).
Remove the reservoir tank assembly (A) after removing the bolts and nut.
Tightening torque : 6.9 - 10,8 N·m
Washer Fluid Level Sensor Reservoir tank
Installation
When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Install in the reverse order of removal.
Wiper Washer Motor Inspection
Inspection
Washer Motor
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
Open the front trunk (A).
Open the auxiliary 12 V battery service cover (A).
Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).
Tightening torque : 7.8 - 9,8 N·m
Disconnect the service interlock connector (A).
Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
The service interlock connector cannot be completely removed.
Before filling the reservoir tank with water, check the filter for foreign material or contamination. if necessary, clean the filter.
Using low-grade washer fluid may clog the washer pump and cause the malfunction of the pump motor.
Fill the washer fluid after installing the washer motor in the reservoir tank.
Connect positive ( + ) battery cables to terminal 2 and negative ( - ) battery cables to terminal 1 respectively.
Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles.
If they are abnormal, replace the washer motor.
Terminal
Function
1
Washer ( + )
2
Ground
Drain the washer fluid below the washer level sensor position.
Disconnect the sensor switch connector (2 pins) and check the current state between the terminals.