Body (Interior / Exterior / Electrical)

Interior Trim

33steps
~198min
4/5difficulty
02040608010054.940N·mlb·ft
Tightening torque found on this page
Done 0 of 33

Contents:

Components and Components Location

Component and Component Location

Interior Trim

1. Cowl Side Trim
2. Front Door Scuff Trim
3. Rear Door Scuff Trim
4. Front Pillar Trim
5. Center Pillar Upper Trim
6. Front Seat Belt
6-a. 44.1 - 55 N·m
7. Center Pillar Lower Trim
8. Rear Transverse Trim
9. Rear Seat Cushion Assembly
10. Rear Seat Back Assembly [Driver's Side]
10-a. 16.7 - 26 N·m
11. Rear Seat Back Assembly [Passenger's Side]
11-a. 16.7 - 26 N·m
12. Luggage Side Trim

Center Pillar Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Center Pillar Lower Trim
  1. Remove the front, rear door scuff trim. (Refer to Interior Trim - "Door Scuff Trim")
  2. Slide the front seat to frontmost position.
  3. Remove the trim (A).
    Clip position :
  4. Remove the center pillar lower trim.
  5. Separate the seat belt (A) after removing the bolt.

    Tightening torque : 44.1 - 55 N·m

  6. Remove the trim (A).
    Clip position :
Center Pillar Upper Trim

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Cowl Side Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door scuff trim. (Refer to Interior Trim - "Door Scuff Trim")
  2. Remove the hood latch release handle. (Refer to Hood - "Hood Latch Release Handle")
  3. Remove the cowl side trim (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Door Scuff Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Door Scuff Trim
  1. Remove the front door body side weatherstrip. (Refer to Front Door - "Front Door Weatherstrip")
  2. Remove the trim (A).
    Clip position :
  3. Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly")
  4. Remove the rear door body side weatherstip. (Refer to Rear Door - "Rear Door Weatherstrip")
  5. Remove the trim (A).
Rear Door Scuff Trim

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Floor Carpet Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.

Front Floor Carpet

  1. Remove the front seat assembly. (Refer to Front Seat - "Front Seat Assembly")
  2. Remove the rear seat cushion and back assembly. (Refer to Rear Seat - "Rear Seat Assembly")
  3. Remove the center pillar lower trim. (Refer to Interior Trim - "Center Pillar Trim")
  4. Remove the cowl side trim (Refer to Interior Trim - "Cowl Side Trim")
  5. Remove the floor console assembly. (Refer to Floor Console - "Floor Console Assembly")
  6. Remove the luggage side trim. (Refer to Luggage Trim - "Luggage Side Trim")
  7. Remove the seat belt anchor (A) after removing the bolt.

    Tightening torque : 44.1 - 55 N·m

  8. Remove the rear seat belt anchor (A) after removing the bolt.

    Tightening torque : 44.1 - 55 N·m

  9. Remove the rear duct cover (A) after removing the screws. [Driver's Side] [Passenger's Side]
  10. Remove the carpet (A).
  11. Remove the carpet pad (A).
  12. Remove the luggage side trim. (Refer to Luggage Trim - "Luggage Side Trim")
  13. Remove the carpet (A).
Rear Floor Carpet

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Front Pillar Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door body side weatherstrip. (Refer to Front Door - "Front Door Weatherstrip")
  2. Remove the clip (A) by pushing in the direction of the arrow. Front Pillar Trim Mounting Clip Separation (Play ▶)

    Video: Front Pillar Trim Mounting Clip Separation

    Notes When Refering Video This video helps clearly identify areas that are hard to distinguish in manual images, such as component locations or assembly structures. It also allows visual confirmation of areas that are difficult to see directly due to restricted visibility caused by surrounding components, from a technician’s perspective.
    • This video is created using common specifications and may differ from the actual vehicle.
    • The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
    • Check the KDS guide for detailed information on how to use the KDS.
    • Check the manual for detailed maintenance procedures.
    • Unauthorized reproduction, distribution, or sharing of this video is prohibited.
  3. Remove the front pillar trim (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Pillar Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the luggage side trim. (Refer to Luggage Trim - "Luggage Side Trim")
  2. Separate the seat belt (A) after removing the bolt.

    Tightening torque : 44.1 - 55 N·m

  3. Remove the rear pillar trim (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.