Body (Interior / Exterior / Electrical)

Mirror

38steps
~228min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 38

Contents:

Inside Mirror Description and Operation. Inside Mirror On Vehicle Inspection

Inside Mirror Description and Operation

Description

Electro Chromic Inside Rear View Mirror
  1. The ECM (Electro Chromatic inside rear view Mirror) automatically dims to protect the driver’s eyes when it senses light reflecting from the car behind.
  2. The sensor in the mirror detects the brightness and if the headlight from the car behind is reflected on the mirror, the chemical layer inside the mirror reacts to glare and adjusts the reflectivity from 10 to 70%.
  3. When switching to the reverse gear, the mirror becomes bright regardless of the surrounding.
  4. The electro chromic inside rear view mirror receives voltage, ground and reverse gear signals.

Inside Mirror On Vehicle Inspection

On Vehicle Inspection

Inspect by performing procedure below to see if the function of the ECM is normal.
  1. After POWER ON, using cloth cover the forward sensor.
  2. It illuminates the rear sensor.
  3. The ECM dims as soon as the rearward-facing sensor detects a certain level of brightness.
    If this test is performed in daytime, the ECM may be darkened as soon as the forward facing sensor is covered.
  4. In the reverse gear, the ECM should not dim.
  5. ECM should not darken when light is illuminated on the front and rear sensors, respectively.

Inside Mirror Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the multi sensor cover. (Refer to Roof Trim - "Multi Sensor Cover")
  3. Disconnect the inside mirror connector (A).
  4. Remove the mirror (A) in the direction of the arrow after removing the screw.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Outside Mirror Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  2. Separate the front door quadrant inner cover (A).
  3. Remove the quadrant inner cover (A) after disconnecting the tweeter speaker connector.
  4. Disconnect the outside mirror connector (A).
  5. Remove the outside mirror assembly (A) after removing the nuts and screw.

    Tightening torque : 6.9 - 10,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Outside Mirror Disassembly and Reassembly

Special Service Tool

Tool Name / Number Illustration Description
Outside Rear View Mirror Glass Remover Tool
0K876 - L2100
Used when removing outside rear view mirror glass
Outside View Mirror Assembly Fixing Stand
0K876 - C5100
Used when fixing the outside rear view mirror assembly

Disassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  • When disassembling the outside rear view mirror, use of special tools can improve workability and safety against damage to parts.
  • The parts where can be worked in assembled state such as scalp or others, proceed with the work on vehicle.
  • The use of special tool is as below.
Outside View Mirror Assembly Fixing Stand (0K876 - C5100)
  1. Mount the special tool bolt (B) to the outside rear view mirror assembly (A) and tighten the bolt fixing nut (C) to fix it so that it does not move.
  2. Turn the handle (B) to set the outside rear view mirror assembly (A) to position where is easy to work.
  3. Remove the mirror (A) by applying slight force, after inserting the special tools as shown below.
Outside Rear View Mirror Glass Remover Tool (0K876 - L2100)

Mirror

  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Separate the mirror (A).
  3. Remove the mirror after disconnecting the mirror heater connector (A) and the rear corner radar indicator connector (B).

Housing Cover

  1. Remove the mirror.
  2. Remove the cover (A) after removing the screws.

Scalp

  1. Remove the housing cover.
  2. Remove the scalp (A).

Mirror Actuator

  1. Remove the mirror.
  2. Separate the actuator (A) after removing the screw.
  3. Remove the actuator after disconnecting the actuator connector (A).

Reassembly

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Outside Mirror Inspection

Inspection

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  2. Disconnect the outside mirror connector.
  3. Apply battery voltage to each terminal as shown in the table and verify that the mirror operates properly. [Mirror Actuator]
    Operate Terminal
    1 2 3
    Up - + +
    Down + - -
    Left - - +
    Right + + -

    [Mirror Heater]
    Operate Terminal
    4 5
    ON + -

    [Side Repeater Lamp]
    Operate Terminal
    8 5
    ON + -

    [BCW Indicator]
    Operate Terminal
    12 11
    ON + -

    [Folding Mirror]
    Operate Terminal
    6 7
    Folding + -
    Unfolding - +

Digital Center Mirror Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Digital Center Mirror Camera
  1. Remove the rear spoiler. (Refer to Body Side Molding - "Rear Spoiler")
  2. Remove the garnish (A) after removing the screw.
  3. Remove the cover (A).
  4. Remove the camera (A) after removing the screws.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.