Body (Interior / Exterior / Electrical)

Infotainment System

89steps
~534min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 89

Contents:

Antenna Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.

Roof Shark Fin Antenna

  1. Remove the roof trim assembly. (Refer to Roof Trim - "Roof Trim Assembly")
  2. Disconnect the antenna connector (A) and remove the nut.

    Tightening torque : 7.8 - 11,8 N·m

  3. Remove the antenna (A).

Crash Pad Antenna

  1. Remove the crash pad assembly. (Refer to Crash Pad - "Crash Pad Assembly")
  2. Remove the air vent duct assembly (A) after removing the screws.
  3. Separate the crash pad antenna (A) after removing the fastener.
    Clip position :
  4. Remove the crash pad antenna (A) after removing the screws.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Cluster Unit On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The cluster unit can quickly diagnosed for problems with KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Cluster Module → CLU Variant Coding)
    Refer to the KDS screen for operating conditions and details

Cluster Unit Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the powernet domain controller. (Refer to Security & Vehicle Ignition System - "Junction Block")
  2. Separate the cluster unit (A) after disconnecting the connectors (B).
  3. Remove the unit (A) after removing the bolt and nuts.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the cluster unit. (S/W Management → Cluster Module → CLU Variant Coding)
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Connected Car Navigation Cockpit (ccNC) On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The Connected Car Navigation Unit (ccNC) can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Connected Car Navigation Cockpit → HUD Calibration) (S/W Management → Connected Car Navigation Cockpit → AVN/Audio Diagnostic Mode) (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Learning Mode) (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Neutralization Mode) (S/W Management → Connected Car Navigation Cockpit → ESC Variant Coding)
    Refer to the KDS screen for operating conditions and details

Connected Car Navigation Cockpit (ccNC) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the order below with the KDS before removing the Connected Car Navigation Cockpit (ccNC). (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Neutralization Mode)
    Refer to the KDS screen for operating conditions and details.
  2. Remove the crash pad center panel. (Refer to Crash Pad - "Crash Pad Panel")
  3. Separate the connected car navigation cockpit (ccNC) (A) after disconnecting the connector (B).
  4. Remove the unit (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the Connected Car Navigation Cockpit (ccNC). (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Learning Mode) (S/W Management → Connected Car Navigation Cockpit → ESC Variant Coding) (S/W Management → Wide Rear View Camera → Variant Coding)
    Refer to the KDS screen for operating conditions and details.
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

External AMP On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The external amplifier can quickly diagnosed for problems with KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Amplifier → AMP Operation Test)
    Refer to the KDS screen for operating conditions and details

External AMP Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear seat assembly. (Refer to Rear Seat - "Rear Seat Assembly")
  2. Separate the floor carpet (A) in the direction of the arrow.
  3. Disconnect the external amplifier connectors (A).
  4. Remove the external amplifier (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Infotainment Keyboard On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The infotainment keyboard can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details

Infotainment Keyboard Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the crash pad center garnish [RH]. (Refer to Crash Pad - "Crash Pad Garnish")
  2. Separate the infotainment keyboard after removing the screws.
  3. Remove the keyboard after disconnecting the connectors (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the Over The Air (OTA) controller S/W update with KDS when replacing the infotainment keyboard. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Integrated Monitor Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear display cover. (Refer to Crash Pad - "Crash Pad Cover")
  2. Separate the integrated monitor (A) after removing the screws.
  3. Remove the monitor (A) after disconnecting the connectors (B).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the integrated monitor. (S/W Management → Cluster Module → CLU Variant Coding)
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Mic Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the overhead console lamp. (Refer to Light & Vision System - "Overhead Console Lamp")
  2. Remove the hands-free microphone (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Mic Inspection

Inspection

  1. Remove the overhead console lamp. (Refer to Light & Vision System - "Overhead Console Lamp")
  2. Check the continuity between terminals.

Multimedia Jack Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the front console cover. (Refer to Floor Console - "Front Console Cover")
  2. Remove the infotainment jack (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Speaker Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Front Center Speaker
  1. Remove the center speaker grille. (Refer to Crash Pad - "Crash Pad Cover")
  2. Separate the speaker (A) after removing the screws.
  3. Remove the speaker after disconnecting the speaker connector (A).
  4. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  5. Remove the side speaker grille. (Refer to Crash Pad - "Crash Pad Cover")
  6. Remove the speaker (A) after removing the screws.
  7. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  8. Remove the front door quadrant inner cover (A).
  9. Separate the speaker connector (A).
  10. Remove the speaker (A) after removing the screws.
  11. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  12. Separate the speaker connector (A).
  13. Remove the speaker (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

  14. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim")
  15. Separate the speaker connector (A).
  16. Remove the speaker (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

  17. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim")
  18. Remove the speaker (A) after removing the screws.
  19. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  20. Remove the woofer speaker cover. (Refer to Luggage Trim - "Rear Transverse Trim")
  21. Remove the subwoofer speaker reinforcement (A) after removing the bolts.
  22. Separate the speaker connector (A).
  23. Remove the speaker (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

  24. Remove the luggage side trim. (Refer to Luggage Trim - "Luggage Side Trim")
  25. Separate the speaker connector (A).
  26. Remove the speaker (A) after removing the nuts.

    Tightening torque : 7.8 - 11,8 N·m

Front Midrange Speaker Front Tweeter Speaker Front Door Speaker Rear Door Speaker Rear Tweeter Speaker Subwoofer Speaker Surround Speaker

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Speaker Inspection

Inspection

Basic Inspection
  1. Remove the speaker by removing the screws to prevent interference with the body trim and surrounding parts.
  2. After removing the speaker, check the sound quality of the speaker with the connector plugged in.
  3. Abnormal vibration
    1. Make sure the mounting screws are properly tightened before replacing the speaker.
    2. Reinstall the speaker and check that the symptom is resolved.
    3. If the symptom does not disappear, replace the speaker with a new one.
  4. Noise
    1. Check that the speaker connector is properly connected and reinstall the connector if necessary.
      • If noises occur in radio mode, turn to the media player mode.
      • If noises occur in both modes, replace the speaker with a new one.
      If noises occur only in the radio mode, the poor radio reception is the cause so do not replace the speaker.
  5. Malfunctions
    • Check the plus (+) and negative (-) speaker terminals using an ohmmeter.
Individual Inspection

Steering Wheel Remote Controller On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The steering wheel remote control can quickly diagnosed for problems with KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details

Steering Wheel Remote Controller Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the steering wheel. (Refer to Steering System - "Steering Wheel")
  2. Remove the paddle shift switch screw (A).
  3. Separate the paddle shift switch (A).
  4. Disconnect the paddle shift connector (B), and then remove the paddle shift switch (A).
  5. Remove the steering wheel lower cover (A) after removing the screws.
  6. Disconnect the remote control switch connectors (A).
  7. Disconnect the steering wheel extension wiring connector (A).
  8. Remove the extension wiring ground screw (A).
  9. Remove the steering wheel dynamic damper (A) after removing the screws.
  10. Disconnect the Hands on Detector (HoD) controller connector (A).
  11. Remove the steering wheel extension wiring (A).
  12. Remove the screws (A).
  13. Remove the steering wheel remote control (SWRC) switch and bezel (A).
  14. Remove the screws (A).
  15. Remove the SWRC switches (A).
  16. Remove the drive mode switch screw (A).
  17. Remove the drive mode switch (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.