Body (Interior / Exterior / Electrical)

Rear Seat

62steps
~372min
4/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 62

Contents:

Rear Seat Assembly Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Rear Seat Cushion Assembly
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the rear seat cushion assembly (A) after pulling the front part (B) of the cushion and pull upwards.
  3. Disconnect the cushion assembly connector (A).
  4. Disconnect the cushion assembly main connector (A).
  5. Remove the rear seat cushion assembly.
  6. Separate the folding lever cable (B) after opening the cap (A).
  7. Remove the seat back assembly (A) after removing the bolts.

    Tightening torque : 16.7 - 26 N·m

  8. Disconnect the rear seat connector (A).
  9. Remove the rear seat cushion assembly.
  10. Separate the folding lever cable (B) after opening the cap (A).
  11. Remove the seat back assembly (A) after removing the bolts.

    Tightening torque : 16.7 - 26 N·m

  12. Disconnect the connectors (A, B). A: Seat belt assembly connector B: Seat belt reminder connector
Rear Seat Back Assembly [Driver's Side] Rear Seat Back Assembly [Passenger's Side]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Seat Back Cover Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Driver's Side
  1. Remove the rear seat back cover assembly. (Refer to Rear Seat - "Rear Seat Back Cover Assembly")
  2. Remove the velcro tape (A) and the hog ring clips (B).
  3. Separate the rear seat back cover (A) and the rear seat back pad (B).
  4. Remove the rear seat back cover assembly. (Refer to Rear Seat - "Rear Seat Back Cover Assembly")
  5. Remove the hog ring clips (A) and velcro tapes (B).
  6. Separate the rear seat back cover (A) and the rear seat back pad (B).
Passenger's Side

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Seat Back Cover Assembly Removal and Installation

Replacement

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Driver's Side
  1. Remove the rear seat outer shield cover. (Refer to Rear Seat - "Rear Seat Shield Cover")
  2. Remove the headrest (A) by pulling it in the direction of the arrow.
  3. Remove the headrest guides (A) by pulling it in the direction of the arrow.
  4. Separate the seat back protector (A) after removing the clip.
  5. Remove the seat back lower armrest (A) after removing the screws.
  6. Remove the armrest (A) after removing the bolt.
  7. Remove the armrest board garnish (A).
  8. Remove the armrest board (A) after removing the screws.
    Clip position :
  9. Remove the center seat belt (A) after removing the bolt.

    Tightening torque : 44.1 - 54 N·m

  10. Remove the tether garnish (A).
  11. Remove the seat back cover protector (A).
  12. Open the seat back cover zipper (A).
  13. Remove the rear seat back board (A) after removing the hog ring clips (B).
  14. Remove the rear seat heating harness (A, B).
    Clip position :
  15. Remove the rear seat back assembly (A) from the rear seat back frame (B).
  16. Remove the rear seat outer shield cover and inner shield cover. (Refer to Rear Seat - "Rear Seat Shield Cover")
  17. Remove the headrest (A) by pulling it in the direction of the arrow.
  18. Remove the headrest guides (A) by pulling it in the direction of the arrow.
  19. Remove the tether garnish (A).
  20. Open the seat back cover zipper (A).
  21. Remove the seat back cover protectors (A).
  22. Remove the seat back cover (A) in the direction of the arrow after opening the zipper.
  23. Remove the seat back board (A) after removing the hog ring clips (B).
  24. Disconnect the heated wire connector (A).
  25. Remove the rear seat heating harness (A).
    Clip position :
  26. Remove the rear seat back assembly (A) from the rear seat back frame (B).
Passenger's Side

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Seat Cushion Cover Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly")
  2. Remove the rear seat cushion cover hog ring clips (A) and velcro tape (B). [Rear] [Front]
  3. Separate the rear seat cushion cover (A) and the rear seat cushion pad (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Seat Shield Cover Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Outer Shield Cover [Driver' Side]
  1. Remove the rear seat assembly [Driver's side]. (Refer to Rear Seat - "Rear Seat Assembly")
  2. Remove the recliner lever (A) after removing the screw.
  3. Remove the cover (A) after removing the screws.
  4. Remove the rear seat assembly [Passenger's side]. (Refer to Rear Seat - "Rear Seat Assembly")
  5. Remove the recliner lever (A) after removing the screw.
  6. Remove the cover (A) after removing the screws.
  7. Remove the rear seat assembly [Passenger's side]. (Refer to Rear Seat - "Rear Seat Assembly")
  8. Remove the cover (A) after removing the screw.
    Clip position :
Outer Shield Cover [Passenger's Side] Inner Shield Cover [Passenger's Side]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Seat Switch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Rear Seat Folding Switch
  1. Remove the luggage side trim. (Refer to Luggage Trim - "Luggage Side Trim")
  2. Remove the switch (A) after removing the screws.
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Seat Unit Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Rear Seat Heater Unit
  1. Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly")
  2. Disconnect the unit connector (A).
  3. Remove the unit (A) after removing the screws.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. When replacing the seat unit, perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")