Body (Interior / Exterior / Electrical)

Security & Vehicle Ignition System

119steps
~714min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 119

Contents:

Body Domain Control Unit Description and Operation

Description and Operation

Body Domain Control Unit (BDC) The body domain control unit is a unit that integrates functions such as a body control module (BCM), a smart key unit (SMK), a tire pressure monitoring system (TPMS), and an immobilizer.
  1. Body Control Module Functions
    Burglar Alarm Tailgate Burglar Alarm Issues an alarm depending on the tailgate operation.
    Panic Alarm Generates warning sound and displays flasher lamp (horn & flasher) depending on the panic signal.
    Security Lamp Control Controls security lamp in vehicle alert status.
    External Lamp Tail Lamp Turns on / off the tail lamp automatically. It also turns off the tail lamp automatically when the driver forgot to turn off the lamp switch.
    Auto Light Turns on/off the tail lamp and headlamp automatically depending on whether it is day or night when the headlamp switch is placed at Auto.
    Welcome Light The welcome light function turns on the headlamp and tail lamp for 15 seconds when an unlock signal is detected while vehicle door is locked.
    Escort Function Turns on the escort lamp when the power is turned off while the headlamp is on.
    • It turns on the headlamp and maintains the state for 20 minutes if POWER is turned off while the headlamp is on.
    • The headlamp remains on only for 30 seconds when the driver seat door is opened and closed during the 20 minute period.
    • The headlamp turns off when remote control lock button is pressed twice while the headlamp is on.
    Headlamp (Low Beam / High Beam) Controls high beam / low beam depending on the headlamp switch (multifunction switch).
    Daytime Driving Light Control Controls the daytime driving light lamp depending on the conditions at the time of vehicle start.
    Telematics (MTS) MTS Alarm Control Controls the output of the door lock/unlock/remote start/panic function in response to the signal transmitted by the MTS unit
    Front / Rear Parking Assist (PDW) PDW Display Receives a signal from parking assist sensor through LIN communication and displays it on the instrument cluster.
    PDW Warning Detects obstacles in front and rear sides using the ultrasonic sensor (PDW) in the case of gear range ("R" or "D") and issues a warning if there is an obstacle.
    Warning Seat Belt Reminder and Indicator Lamp Issues a warning if the seat belt is not fastened, and prevents pattern activation if the vehicle is driven while the seat belt is not fastened.
    Key Reminder Warning Issues a warning if the driver seat door is open while ACC is on.
    Key Reminder Warning Issues a warning if the driver seat door is open while POWER is on.
    Sunroof Open Warning Alarm output function when getting out of the car by removing the key while the sunroof is open
    Wiper and Washer Wiper (Low / High / Mist / Auto) Controls wiper operating power and fail-safe circuit.
    Wiper Control the washer interlocking wiper.
  2. Smart Key Unit Functions
    SMK Door Lock and Unlock Locks/Unlocks the door based on the door unlock signal and the signal from push buttons on the driver's / passenger's side outside handles.
    SMK Welcome Light Controls door mirror and puddle lamp after smart key authentication when the driver with smart key approaches the vehicle.
    Power Tailgate When holding a smart key and staying in the rear bumper (in the LF antenna area) for more than 3 seconds, the power tailgate opening function is performed.
    SMK Warning Key Reminder 1 When the driver attempts to lock the door, it checks if there is a smart key inside the vehicle and unlocks the door if there is one.
    Key Reminder 2 Checks the door lock status for 0.5 seconds after the vehicle door is closed and unlocks the door and generates a warning sound using the external buzzer if the door is locked.
    Door Lock Warning 1 Generates a warning sound with the external buzzer if the driver tries to leave the vehicle while POWER ON.
    Door Lock Warning 2 Generates a warning sound with the external buzzer if the driver tries to lock the door and leave the vehicle while one or more doors are open.
    Door Lock Warning 3 Searches for a smart key inside the vehicle when the driver tries to lock the door, and issues a warning and does not lock the door if there is a smart key inside.
    Key Out Lamp Warning If the vehicle moves at 3 km/h or less while POWER ON and the door is open, it searches for the smart key every 3 seconds and blinks the warning lamp if there is no smart key.
    SMK RKE (Remote Keyless Entry) Door Lock / Unlock Locks/Unlocks the door based on the door unlock signal and the signal from push buttons on the driver's / passenger's side outside handles.
    Panic Performs vehicle panic and panic stop functions based on the panic button signal.
    Engine Start Start stop button (SSB), immobilizer, start relay power control, SSB Lamp Control.
  3. Tire Pressure Monitoring System (TPMS) Functions Tire pressure monitoring system continuously monitors pressure and temperature inside the tire in order to warn the driver of the changes in tire pressure that may have influence on vehicle driving conditions. TPMS control module analyzes the data from the WE (Wheel Electronic) sensor attached inside each wheel and determines the tire conditions and generates a signal that is necessary for warning lamp control.
  4. Identity Authentication Unit (IAU) Function The IAU receives the encrypted digital key value from the smartphone, decrypts it, analyzes it, and delivers the authentication result to the BDC.

Body Domain Control Unit On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The Body Domain Control unit (BDC) can quickly diagnosed for problems with the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → BDC-BCM → Variant Coding) (S/W Management → BDC-SMK → Smart Key Code Saving) (S/W Management → BDC-TPMS → ID Writing) (S/W Management → BDC-IAU → Status Information) (S/W Management → BDC-IAU → Learning Mode) (S/W Management → BDC-IAU → IAU Neutralization Mode) (S/W Management → BDC-IAU → Activate Card Key Registration Mode)
    Refer to the KDS screen for operating conditions and details

Body Domain Control Unit Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the order below with the KDS before removing the Body Domain Control unit (BDC). (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Neutralization Mode) (S/W Management → BDC-IAU → IAU Neutralization Mode)
    Refer to the KDS screen for operating conditions and details.
  2. Remove the crash pad assembly. (Refer to Crash Pad - "Crash Pad Assembly")
  3. Separate the body domain control unit (A) after removing the bolts and nut.

    Tightening torque : 7.8 - 11,8 N·m

  4. Remove the unit (A) after disconnecting the connector (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the body domain control unit. (S/W Management → BDC-BCM → Variant Coding) (S/W Management → BDC-SMK → Smart Key Code Saving) (S/W Management → BDC-TPMS → ID Writing) (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Learning Mode) (S/W Management → BDC-IAU → Learning Mode)
    Refer to the KDS screen for operating conditions and details.
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Button Engine Start System Description and Operation

Description

System Overview

System characteristics :
  • Changing the state of power by using the start button.
  • Controlling external relays for POWER ON / DRIVE READY terminal switching and STARTER, without use of mechanical IG switch.
  • Indicating the vehicle status on cluster by displaying messages.
  • Immobilizer function by LF transponder communication between between fob and button start switch.
  • Interface with Low Speed CAN vehicle communication network.
  • Interface with LIN vehicle communication network depending on platform.
System Main Function
  • Switching of POWER ON / DRIVE READY terminal.
  • Control of the STARTER relay based on communication with Vehicle Control Unit (VCU).
  • Management of the Immobilizer function.
  • Management of Button Start System warning function.
Wireless Communications The electric signal is used to exchange information between vehicle and FOB key. For now, button start is applied with smart key FOB key together. Smart key function is explained separately so refer to the corresponding system contents. System Flow Chart Schematic Diagram Body Domain Control Unit (BDC) Body domain control unit function :
  • Start/Stop Button (SSB) control
  • Immobilizer communication (with VCU for releasing immobilizer)
  • Authentication server (Validity of Transponder and in case of Smart Key option Passive FOB authentication)
  • System consistency monitoring
  • System diagnosis
  • Control of display message / warning buzzer
Limp Home Mode
  • In case of no input signal for the brake switch, the POWER OFF mode shall cycle to “START” by pressing SSB for more than 10 seconds.
  • In case of problems with communication between VCU and CAN (the VCU state), the “START” state cycles to the “EV Ready” based on rpm input.
  • In case that one out of two SSB input lines is disconnected, the electric power cycling is available when SSB is pressed twice within 10 seconds. The buzzer rings when the button is pressed for the first time. Electric power cycling is available and buzzer stops when the button is pressed twice within 10 seconds.
Terminal and Starter Relay Relay is used to switch the terminal POWER ON / DRIVE READY. Normally-open relay is operated by smart key unit. One relay coil is connected to output terminal of IBU.

Button Engine Start System Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the Start/Stop Button (SSB). (Refer to Floor Console - "Console Upper Cover")

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Central Communication Unit (CCU) On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The central communication unit (CCU) can be quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Central Communication Unit (CCNF) → Variant Coding) (S/W Management → Central Communication Unit (CCNF) → OTA Initialization)
    Refer to the KDS screen for operating conditions and details

Central Communication Unit (CCU) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the crash pad lower panel. (Refer to Crash Pad - "Crash Pad Panel")
  2. Lower the steering column after removing the nuts and through-bolt. (Refer to Steering System - "MDPS Column and Housing")
  3. Separate the central communication unit (CCU) (A) after removing the bolts.

    Tightening torque : 6.9 - 10,8 N·m

  4. Remove the CCU (A) after disconnecting the connectors (B).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the Central Communication Unit (CCU). (S/W Management → Central Communication Unit (CCNF) → Variant Coding)
    Refer to the KDS screen for operating conditions and details
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Data Connectivity Unit (DCU) On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The Data Connectivity Unit (DCU) can be quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details

Data Connectivity Unit (DCU) Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the center crash pad panel. (Refer to Crash Pad - "Crash Pad Panel")
  2. Separate the Data Connectivity Unit (DCU) (A) after disconnecting the DCU connector (B).
  3. Remove the DCU (A) after removing the nuts.

    Tightening torque : 7.8 - 11,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. When replacing the Data Connectivity Unit (DCU), perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Digital Key System On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The digital key system can quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment.
    Refer to the KDS screen for operating conditions and details

Digital Key System Description and Operation

Description

Digital key system allows a driver to lock or unlock the vehicle doors with smartphone app or a NFC key card without a smart key.

Main features of digital key system

  • A smartphone key can be issued from the digital key server and a NFC key card can be registered through a separate process.
  • The smartphone key can be registered through the ccNC screen of the vehicle by downloading the app after registering as a member on the Kia website.
  • The NFC card key can be registered through the ccNC screen of the vehicle after going through a separate authentication process. (The separate authentication procedure is available with the digital key app or selecting “Card key registration mode activation” using the KDS.)
  • 3 drivers can share a smartphone key at maximum but one NFC key card is provided.
  • When registering a smartphone key or an NFC card key, the user must possess the smart key, and after registration, door lock/unlock and start functions can be performed without carrying the smart key.
  • If a smartphone is set up in the driver's profile (Profile 1, Profile 2, Guest) through the ccNC screen, the driver is automatically recognized when the door is unlocked and the personal preference function (IMS, ccNC, etc.) is executed.
  • Vehicle status information (mileage, fuel economy, battery level, etc.) can be checked on the smartphone app.
  • When you delete the smartphone key or NFC key card, you should have the smart key. (Smartphone key or NFC key card is not required to carry to delete.)
  • Register a smartphone key or NFC key card using the registration process below. Smartphone Key/NFC Key Card Registration Process
    Step 1. Sign up for membership 2. Install App & Login 3. Key Registration 4. Entry/Start 5. Key Sharing
    Description Create an account on the Kia membership website Install the Kia Connect APP on your smartphone and login Get in the car with the FOB key and register the smartphone and the NFC card key NFC door lock/unlock, NFC vehicle start, remote control via APP Digital key can be shared with others with the APP

Digital Key System NFC Key Card Registration

NFC Key Card Registration Process

The digital key system provides an NFC key card for emergency purposes, such as when a smartphone cannot be delivered directly, such as valet parking, or when the smartphone battery is off. The card key must be registered in the vehicle for the first time after the vehicle is shipped or the first time after replacing the BDC to be used. NFC Key Card Registration Process You should follow the steps in the procedure below to register NFC key card.
  1. Make the vehicle enable to register NFC key card.
    It can be registered with KDS - S/W Management - "Card Key Registration Mode Activation".
    It also can be registered digital key app available in the vehicle.
  2. You should register the NFC key card on AVNT or the cluster within 5 minutes after getting in the vehicle.
    • When there is a previously enrolled NFC key card, the “Enroll” button on the User’s Settings menu is deactivated so press “Deletion” button to delete the NFC key card and register new one. (You should have your smart key to delete in the vehicle)
    • A NFC key card can be registered and deleted repeatedly but if you enroll a new NFC key card, the previously enrolled key is not available.
    • When replacing the BDC-IAU (authentication controller), the previously used NFC card key cannot be used.
    • iPhone users and non-smartphone users can register the NFC card key with KDS - S/W Management - "Card Key Registration Mode Activation".
    • You should register the NFC key card in the vehicle within 5 minutes after proceeding authentication process.
    • If the enrollment process fails to be completed within 5 minutes, you should retry after re-processing the authentication.
  3. Perform the "Card Key Registration Mode Activation" by using the KDS. (S/W Management → BDC-IAU → Card Key Registration Mode Activation)
    Refer to the KDS screen for operating conditions and details
  4. After placing the card key on the NFC wireless charger, register the card key on the ccNC screen.
    • You should get in the vehicle within 5 minutes and register the key card After completing “Key Card Enroll Mode” by using the KDS.
    • When you register a NFC key card, the smart key should be in the vehicle.
  5. Place the NFC key card that you want to register on the interior authentication pad (Wireless charger) to complete the process.
NFC Key Card Registration by using the KDS.

Digital Key System Digital Key System Inspection

On Vehicle Inspection

Digital Key System Operation Verification
  1. When the digital key system failure occurs, the system operation should be confirmed as below.
    1. Checked the lock/unlock operation by touching the NFC antenna portion of the door handle with a smart phone or NFC card key.
    2. Check whether the start-up is working or not after placing your smart phone or key card on the wireless charger.
    3. Make sure confirm whether BLE lock or unlock are operable with the smart phone.
    4. If there is an abnormality in the operation of the digital key system, the inspection is performed according to the "Digital Key System A/S procedure" below.
Digital Key System A/S Procedure
  • To inspect the digital key, vehicle owner’s smart phone or NFC card key is required. If you do not have both of those, you should register new NFC card key and complete the test before delivering the vehicle.
  • Once a new NFC key card is registered, the existing NFC key card is not available.
Inspection 1 : Check whether the door handles of driver’s seat and passenger’s seats work properly. If the door handle of the driver’s seat fails to operate, the handle should be checked after replacing with passenger’s seat door handle. If it works properly, only the door handles of driver’s seat should be replaced since it does not have problem with wiring. If both of those handles do not work, the door handles of driver’s seat and passenger’s seat should be replaced with a new handle to check whether it works properly. If it performs normally, the handle should be replaced with a new one. However, there is a malfunction in the part, you assume (B166D00 driver’s seat door handle malfunction) or (B166E00 passenger’s seat door handle malfunction) occurs and process inspections in accordance with “DTC Diagnosis Guide”.
Inspection 2 : Check whether the tart-up with the digital key (smart phone or card key) after replacing with new wireless charger. If it works properly, the vehicle can be delivered with the function on since it does not have a problem with wiring. If it does not work even after replacing with a new product, the wireless charger wiring should be checked.
Inspection 3 : After replacing with a new BLE module, check whether the digital key works. If it does not work even after replacing with a new product, the wireless charger wiring should be checked. If there is not a problem with wiring, we assume (B165A00 BLE module malfunction), (B167F00 LIN communication failure between IAU and BLE modules) occurs and process inspections in accordance with “DTC Diagnosis Guide”.
Inspection 4 : Process above “Inspection 1” and “Inspection 2” in order.
Inspection 5 : Process above “Inspection 1” and “Inspection 3” in order.
Inspection 6 : Process above “Inspection 1” and “Inspection 3” in order.
Inspection 7 : If it operates without any problem after processing from No.1 to No.3 with the digital key, the vehicle can be delivered with the function on since it does not have a problem with wiring. If it does not work, assume that (B165C00 IAU-BDC learning anomaly) has occurred and perform a check according to the "DTC Guide". If still does not operate, “Inspection 1”, “Inspection 2”and “Inspection 3” should be processes in order. If any one of the three works normally, check the wiring of the remaining cases, and if all three do not work, replace the BDC with a new one and perform "EMS/FOB learning" and "IAU-BDC learning". Since the BDC has been replaced with a new one, perform "Check 1", "Check 2", and "Check 3" in order to check the system operation.
IAU-BDC learning status inspection
Digital key function works only when the learning states of IAU and BDC are learnt.
  1. Perform the "Status Information" procedure by using the KDS. (S/W Management → BDC-IAU → IAU Status Information)
    Refer to the KDS screen for operating conditions and details
    Mark Description Learning status
    Virgin Initial state Non-learning state
    Learnt Learning completiond state Learning completiond state
    Neutralized Neutral state Non-learning state
Smartphone Key Registration Status Inspection
Smart phone key registration status can be checked via "Data Analysis".
  1. Connect KDS to vehicle.
  2. Select the "Data Analysis" and "IAU".
    Mark Description
    Owner's smartphone registration state 0 : Main user's smart phone is not registered.
    1 : Main user's smart phone is registered.
    Number of currently registered digital key (smartphones) 0 : No registered phone.
    1-4 : Currently registered device number.
NFC Key Card registration status Inspection
Smart phone key registration status can be checked via "Data Analysis".
  1. Connect KDS to vehicle.
  2. Select the "Data Analysis" and "IAU".
    Mark Description
    Number of currently registered digital key (card key) 0 : No registered card.
    1 : registered 1 card.

Digital Key System Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Ultra Wideband Unit [Front Bumper Side]
  1. Remove the front bumper assembly. (Refer to Front & Rear Bumper - "Front Bumper Assembly")
  2. Disconnect the unit connector (A).
  3. Remove the unit (A).
Clip position :
Ultra Wideband Unit [Rear Bumper Side]
  1. Remove the rear bumper assembly. (Refer to Front & Rear Bumper - "Rear Bumper Assembly")
  2. Disconnect the unit connector (A).
  3. Remove the unit (A).
Clip position :
Ultra Wideband and BLE Unit
  1. Remove the roof trim assembly. (Refer to Roof Trim - "Roof Trim Assembly")
  2. Disconnect the unit connector (A). [Master] [Slave]
  3. Remove the unit (A). [Master] [Slave]
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. When replacing the ultra-wideband and BLE unit, perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Fingerprint Authentication System Description and Operation. Fingerprint Authentication System Troubleshooting

Fingerprint Authentication System Description and Operation

Description and Operation

The fingerprint authentication system recognizes a user with a registered fingerprint and provides the convenience of starting a vehicle without a smart key or making electronic payments without entering a password. Major Features of the Fingerprint Recognition System
  • AVN link: Reinforcing driver convenience and security such as personalization, profile lock & unlock, electronic payment and valet parking mode using pre-registered fingerprint information.
  • Engine start: Start the engine and drive with pre-registered fingerprint information.

Fingerprint Authentication System Troubleshooting

Troubleshooting

Fingerprint Authentication System On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The fingerprint authentication system can quickly diagnosed for problems with the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Fingerprint Recognition Module → Status Information) (S/W Management → Fingerprint Recognition Module → FPM Self-Diagnosis Test) (S/W Management → Fingerprint Recognition Module → Check Registered Fingerprint Status) (S/W Management → Fingerprint Recognition Module → Fingerprint Sensor Contact Inspection)
    Refer to the KDS screen for operating conditions and details

Fingerprint Authentication System Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Perform the order below with the KDS before removing the fingerprint recognition unit. (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Neutralization Mode) (S/W Management → BDC-IAU → IAU Neutralization Mode)
    Refer to the KDS screen for operating conditions and details.
  2. Remove the fingerprint recognition unit. (Refer to Floor Console - "Console Upper Cover")

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the fingerprint recognition unit. (S/W Management → BDC-IAU → Learning Mode) (S/W Management → Connected Car Navigation Cockpit → AVN-FPM Learning Mode)
    Refer to the KDS screen for operating conditions and details.
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Junction Block On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. PowerNet domain controllers can quickly diagnosed for problems with KDS. (Refer to "DTC Guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Powernet Domain Controller → Variant Coding) (S/W Management → Powernet Domain Controller → Mode Setting)
    Refer to the KDS screen for operating conditions and details

Junction Block Inspection

Inspection

Power Relay Inspection (Type A) Check for continuity between the terminals.
  1. After supplying power between terminal No. 85 and 86, check that there is continuity between terminal No. 30 and 87.
  2. After supplying power between terminal No. 85 and 86, check that there is no continuity between terminal No. 30 and 87.
    Terminal Operate
    Power ON Power OFF
    30 - 87 Continuity -
  3. After supplying power between terminal No. 86 and 85, check that there is continuity between terminal No. 87 and 30.
  4. After supplying power between terminal No. 86 and 85, check that there is no continuity between terminal No. 87 and 30.
    Terminal Operate
    Power ON Power OFF
    30 - 87 Continuity -
  5. Check for separation of fuse holder and check that the holder is tightly holding the fuse.
  6. Check that each fuse circuit has the exact fuse capacity.
  7. Check the fuses for any damage.
    If a fuse is to be replaced, be sure to use a new fuse of the same capacity.
  8. Disconnect the battery negative ( - ) terminal and the high voltage service interlock connector. (Refer to Battery Control System - "Auxiliary 12 V Battery - 2WD") (Refer to Battery Control System - "Auxiliary 12 V Battery - 4WD")
  9. Remove the multi fuse (A) in the direction of the arrow after removing the nut.
  10. Remove the multi-fuse (A) by pulling it in the direction of the arrow.
  11. Remove the multi fuse (A) in the direction of the arrow after removing the nut.
  12. Check the multi-fuses for any damage.
    Use the multi-fuse of the correct fuse specification.
Power Relay (Type B) Check for continuity between the terminals. Fuse Multi-Fuse

Junction Block Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
PCB Block
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the PCB block (A) after pushing the mounting hooks in the direction of the arrow.
  3. Disconnect the PCB block connector (A).
  4. Remove the crash pad lower panel. (Refer to Crash Pad - "Crash Pad Panel")
  5. Disconnect the powernet domain controller connectors (A).
  6. Separate the powernet domain controller (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

  7. Remove the powernet domain controller (A) after disconnecting the connectors (B).
Powernet Domain Controller

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the Powernet domain controller. (S/W Management → Powernet Domain Controller → Variant Coding)
    Refer to the KDS screen for operating conditions and details
  3. When replacing PowerNet domain controller, Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")

Over The Air (OTA) Description and Operation. Over The Air (OTA) OTA Update Sequence

Over The Air (OTA) Description and Operation

Description and Operation

  • OTA (Over The Air) is a function that wirelessly updates the vehicle's controller software.
  • It provides a service that enables direct wireless communication to update the electronic control unit software, which was only possible by visiting a service center.
OTA System Flow Chart

Over The Air (OTA) OTA Update Sequence

OTA Update Sequence

  • OTA update downloads S/W wirelessly while driving and updates after turning off the vehicle.
  • Updates are performed in the following order.
  1. After stopping the vehicle, turn off the vehicle and update in order when the update approval information is displayed.
  2. After restarting the vehicle, the update information message is displayed.
    When update fails, check "Part No" and "S/W version" with KDS and try again. (Refer to Over The Air (OTA) - "On Vehicle Inspection")

Over The Air (OTA) On Vehicle Inspection

On Vehicle Inspection

OTA target controller
  • When replacing the OTA target controller, check the S/W version with KDS.
  • If the S/W version of the replaced controller is higher or lower than other controller versions, OTA automatic update is not possible.
No. Controller Detail
1 ACU Airbag Control Unit
2 ADAS_DRV ADAS DRIVING ECU
3 ADAS_PRK ADAS PARKING ECU
4 ADP Acoustic Design Processor
5 ATCU Auto Temperature Control Unit
6 BDC Body Domain Controller
7 BLTN_CAM Built-in Cam
8 BMS Battery Management System
9 ccNC Connected Car Navigation Cockpit
10 CCU Cental Communication Unit
11 CLU Cluster
12 DCU Data Connectivity Unit
13 ECS Electronic Controlled Suspension
14 eLSD Electronic Limited Slip Differential
15 ETCS Electronic Toll Collection System
16 EXT AMP external AMPlifier
17 FPM FingerPrint Module
18 HOD Hand of Detection
19 HUD Head Up display
20 ICC In Cabin Camera
21 ICCU Integrated Charging Control Unit
22 IEB Intergrated Electronic Booster
23 MCU (INVERTER) Motor Control Unit
24 MDPS Motor Driven Power Steering
25 MKBD Multimedia Keyboard
26 MLM Mood Lamp Module
27 PDC Powernet Domain Controller
28 PSM UNIT ASSY-MEMORY POWER SEAT
29 PSU Power Seat Unit
30 PTGM Power Tailgate Module
31 SBCM Side Body Control Module
32 SBW-SHIFTER SBW-SHIFTER
33 SCU SBW Control Unit
34 SHVU Seat Heater&Ventilation Unit
35 UWB_BLE Ultra Wideband & Bluetooth Low Energy
36 VCMS Vehicle Charging Management System
37 VCU Vehicle Control Unit
38 VESS Virtual Engine Sound System
39 WPC UNIT ASSY-WIRELESS CHARGING

Over The Air (OTA) Controller S/W Update
  1. Perform OTA management version update with the KDS.
  2. Turn off the vehicle and connect the KDS.
  3. Enter the service inspection mode. (Refer to Body (Interior / Exterior / Electrical) - "Service Inspection Mode")
  4. Select "Car Model" and select "ECU Upgrade".
  5. Select “OTA Management Version Update”.
    • It is possible to enter OTA management version update without VCI 2 or ECI cable, but the entry and update time may become longer.
    • Ethernet communication controller requires a dedicated cable connection for OTA management version update.
    • VCI 2: ECI module set for VCI 2
    • VCI 3: Ethernet Cable for VCI 3
  6. Update by checking the "Part No" and "S/W version" of the controller.
    • All active buttons must be updated. (Switch to inactive when update is complete)
    • Manual Update Precautions Before work, check if the controller is installed on the vehicle, and if it is installed, check the Part No. and perform the update. (Prevention of erroneous specification update)
    • Conditions for activating the manual update button
    1. Unable to read controller information (controller no response or negative response)
    2. Controller not mounted on vehicle
    • Conditions for activating the auto update button
    1. Matching Part No. (same specifications)
    2. Vehicle S/W version and OTA latest S/W version mismatch (update required)
    ※ Automatic update procedure Displays controller name, Part No, and S/W version information during auto update
    ※ Manual update procedure In a situation, it is difficult to check the controller specification through KDS, check the Part No. of the vehicle controller directly, Perform an update after checking that it is the same as Part No. in the pop-up
  7. Data download and reprogramming are in progress.
  8. When the update is completed, the activated update button is inactivated and the list is updated with completion.
  9. When the update fails, recheck the OTA management version update function entry conditions and Part No.
    When the update is complete, restart the vehicle, wait for 5 minutes, and check if there is no S/W ver error pop-up displayed in ccNC.

ROA (Rear Occupant Alert) System Description and Operation

Description

The system detects the passenger in the vehicle and prevents the driver from getting off the vehicle with the passenger in the back. Order of Operation
Sensor Detection Sensing Control Radar Sensing Warning Control Warning
Driver's door switch
Rear door switch
Body Domain Control Unit (BDC) Rear Occupant Alert (ROA) Unit Body Domain Control Unit (BDC) Cluster pop-up and voice guidance
Horn + Hazard lamp
Kia Connect warning

  • 1st warning : If you open the driver's door after you open and then close the rear door and POWER OFF, the system provides warning by showing message on the cluster and giving voice instruction.
  • 2nd warning :
  1. The system detects the indoor movement using the rear occupant alert sensor installed on the roof trim when the driver gets off the vehicle and locks all the doors.
  2. If any movement inside the vehicle is detected, horn is activated for 25 seconds and the mobile text message is sent. (If Kia Connect equipped)

ROA (Rear Occupant Alert) System On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The Rear Occupant Alert (ROA) system can be quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details

ROA (Rear Occupant Alert) System Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the roof trim assembly. (Refer to Roof Trim - "Roof Trim Assembly")
  2. Disconnect the rear occupant alert sensor (ROA) connector (A).
  3. Remove the ROA (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Side Body Control Unit On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The side body control unit can be quickly diagnosed for problems with the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → Side Body zone Control Module_Driver → Variant Coding) (S/W Management → Side Body zone Control Module_Assist → Variant Coding)
    Refer to the KDS screen for operating conditions and details

Side Body Control Unit Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Side Body Control Unit [Crash Pad Side]
  1. Remove the ADAS parking ECU bracket. (Refer to Advanced Driver Assistance System - "ADAS parking ECU (ADAS_PRK)")
  2. Remove the unit (A) after disconnect the connectors (B).
  3. Remove the unit (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

  4. Remove the luggage side trim. (Refer to Luggage Trim - "Luggage Side Trim")
  5. Separate the floor carpet (A).
  6. Disconnect the unit connector (A).
  7. Remove the unit (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

Side Body Control Unit [Floor Carpet Side]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the order below with the KDS when replacing the side body control unit. (S/W Management → Side Body zone Control Module_Driver → Variant Coding) (S/W Management → Side Body zone Control Module_Assist → Variant Coding)
  3. Perform Over The Air (OTA) controller S/W update with KDS. (Refer to Security & Vehicle Ignition System - "Over The Air (OTA)")
  4. Drive the vehicle at a speed of 20 km/h or above when replacing the side body control unit to activate the unit.

Smart Key System Specification

Specification

RF Receiver
Item Specification
Frequency (MHz) 433.92
Antenna type FSK

Smart Key
Item Specification
Fob key
Battery Lithium battery 3V 1 unit
Distance - The distance over which Radio Frequency (RF) Receiver can receive a FOB transmission signal : 30 m (98.4 ft.)
- The distance over which LF(Low Frequency) antenna(Outer Handle/ Tailgate ) can detect FOB : 0.7m
Battery life More than 2 years (20 times / a day)
Push buttons 7 (Door lock / unlock, Trunk open, Panic, Remote start, Forward / Backward)
Frequency (MHz) 125
Frequency (KHz) 433.92
Numbers 3 units (Fob key 2 units, card key 1 unit)

An inappropriately disposed battery can be harmful to the environment and human health.
Antenna
Item Specification
Rated voltage (V) DC 12
Operating voltage (V) DC 9 - 16
Operating temperature [°C (°F)] -40 to 85 (-40 to 185)
Frequency (KHz) 125
Numbers Interior (3 units), Door (2 units), Front Bumper Beam(1 unit, RSPA Only), Rear Bumper(1unit)

Smart Key System Description and Operation ➤

Smart Key System On Vehicle Inspection. Smart Key System Code Saving

Smart Key System On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The smart key system can quickly diagnosed for problems with the KDS (Refer to "DTC guide").
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    2. S/W Management : Controlling other features including system option setting and zero point adjustment. (S/W Management → BDC-SMK → Neutralization Mode) (S/W Management → BDC-SMK → SMK STATUS INFORMATION) (S/W Management → BDC-SMK → FOB KEY STATUS INFORMATION) (S/W Management → BDC-SMK → Smart Key Code Saving) (S/W Management → BDC-SMK → Antenna Status Check)
    Refer to the KDS screen for operating conditions and details

Smart Key System Code Saving

Code Saving

Refer to the KDS screen for operating conditions and details
Smart Key Code Saving
  1. Select the "Smart Key Code Saving" on the menu with the KDS. (S/W Management → BDC-SMK → Smart Key Code Saving)
  2. Perform the "SMK STATUS INFORMATION" with the KDS. (S/W Management → BDC-SMK → SMK STATUS INFORMATION)
Smart Key Status Check

Smart Key System Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Interior Antenna #1
  1. Remove the front console cover. (Refer to Floor Console - "Front Console Cover")
  2. Disconnect the antenna connector (A).
  3. Remove the antenna (A) after removing the screws.
  4. Remove the floor console assembly. (Refer to Floor Console - "Floor Console Assembly")
  5. Remove the antenna.
    1. Disconnect the antenna connector (B).
    2. Remove the antenna (A) after removing the screws.
  6. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  7. Remove the rear transverse trim. (Refer to Luggage Trim - "Rear Transverse Trim")
  8. Disconnect the antenna connector (A).
  9. Remove the antenna (A) after removing the nuts.
    Tightening torque : 3.9 - 4,2 N·m (0.4 - 0.43 kgf·m, 2.9 - 3.1 lb·ft, 34.7 - 37.3 lb·in)
  10. Remove the rear bumper assembly. (Refer to Front & Rear Bumper - "Rear Bumper Assembly")
  11. Disconnect the antenna connector (A).
  12. Remove the antenna (A) after removing the screws.
  13. Remove the front bumper assembly. (Refer to Front & Rear Bumper - "Front Bumper Assembly")
  14. Disconnect the antenna connector (A).
  15. Remove the antenna (A) after removing the screws.
  16. Remove the front door trim. (Refer to Front Door - "Front Door Trim")
  17. Disconnect the antenna connector (A).
  18. Remove the antenna (A) after removing the screws.
  19. Remove the front bumper assembly. (Refer to Front & Rear Bumper - "Front Bumper Assembly")
  20. Remove the buzzer (A) after disconnecting the connector (B).
Interior Antenna #2 Interior Antenna #3 Rear Bumper Antenna Front Bumper Beam Antenna Front Door Antenna Buzzer

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.