Body (Interior / Exterior / Electrical)

Rear Door

69steps
~414min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 69

Contents:

Components and Components Location

Component and Component Location

Rear Door [Trim]
1. Rear Door Delta Cover
2. Rear Door Frame Molding
3. Rear Door Belt Outside Weatherstrip
4. Rear Door Front Frame Garnish
5. Rear Door Rear Frame Garnish
6. Rear Door Side Weatherstrip
7. Rear Door Body Side Weatherstrip
8. Rear Door Trim
9. Power Window Switch
10. Rear Door Inside Handle
11. Rear Door Belt Inside Weatherstrip

Rear Door [Mechanism]
1. Rear Door Module
1-a. 8.8 - 11,8 N·m
2. Rear Door Window Motor
2-a. 7.8 - 11,8 N·m
3. Rear Door Speaker
3-a. 7.8 - 11,8 N·m
4. Rear Door Window Glass
4-a. 8.8 - 11,8 N·m

5. Rear Door Glass Run
6. Rear Door Channel
6-a. 6.9 - 10,8 N·m
7. Rear Door Latch
8. Rear Door Outside Handle
8-a. 3.4 - 5,7 N·m

Adjustment

Adjustment

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Adjustment
  1. Check that the gap between the door and the body is even after parking in a flat level.
  2. Loosen the door hinge (A) bolts (B), adjust the door (C) by moving it back and forth, left and right, and then tighten the bolts.

    Tightening torque : 21.6 - 26 N·m

  3. Check that the gap between the door and the body is even.
  4. Loosen the screws (B) and adjust the striker (A) by moving it back and forth, left and right, and then tighten the screws.

    Tightening torque : 18.6 - 33 N·m

  5. Check that the door opens and closes properly.
Striker Adjustment Glass Adjustment
Check the damage of the glass run and channel and replace them if necessary.
  1. Remove the rear door trim. (Refer Rear Door - "Rear Door Trim")
  2. Adjust the gap by moving the window glass (A) up, down, left and right, and then tighten the bolt.

    Tightening torque : 8.8 - 11,8 N·m

  3. Check the window glass for normal operation.
  4. With the window open, use the auto/manual up switch to completely close the window and keep it closed for more than 0.2 seconds. (If you operate the up switch while the window is completely closed, it will not be initialized)
Window Motor Reset

On Vehicle Inspection

On Vehicle Inspection

Diagnostic with KDS

  1. The rear door can be quickly diagnosed for problems with the KDS. (Refer to "DTC guide")
    1. Self diagnosis : Inspect the Diagnostic Trouble Code (DTC) with the KDS. (Refer to DTC guide when fault code is found.)
    Refer to the KDS screen for operating conditions and details
  2. The motor can continuously operate at least 15 strokes, and it can be operated again 30 to 40 seconds after the motor stops due to the overheat protection function.
Protection of Window Motor Overheating

Rear Door Garnish and Molding Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Frame Molding
  1. Remove the molding (A).
    Clip position :
  2. Remove the rear door belt outside weatherstrip. (Refer to Rear Door - "Rear Door Weatherstrip")
  3. Remove the garnish (A).
  4. Remove the rear door delta cover. (Refer Rear Door - "Rear Door Trim")
  5. Remove the rear door belt outside weatherstrip. (Refer to Rear Door - "Rear Door Weatherstrip")
  6. Remove the screw (A).
  7. Remove the garnish (A).
    Clip position :
Door Frame Garnish [Front Side] Door Frame Garnish [Rear Side]

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Handle Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Inside Handle
  1. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim")
  2. Remove the handle (A) after removing the screws.
  3. Remove the rear door module. (Refer to Rear Door - "Rear Door Module")
  4. Disconnect the handle connector (A).
  5. Separate the connector wiring (A).
    Clip position :
  6. Separate the door latch rod (A).
  7. Remove the handle (A) after removing the nuts.

    Tightening torque : 3.4 - 5,7 N·m

Door Outside Handle

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Latch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear door module. (Refer to Rear Door - "Rear Door Module")
  2. Remove the door channel (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

  3. Disconnect the door outside handle connector (A).
  4. Separate the connector wiring (A).
    Clip position :
  5. Separate the door latch rod (A).
  6. Remove the screws (A).

    Tightening torque : 6.9 - 10,8 N·m

  7. Remove the door latch (A).

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Latch Inspection

Inspection

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear door latch. (Refer to Rear Door - "Rear Door Latch")
  2. Apply voltage to connector terminal and check that the door latch operates properly.
    Location Terminal
    Driver 7, 8
    Passenger 1, 2

Rear Door Module Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Remove the rear door window glass. (Refer to Rear Door - "Rear Door Window Glass")
  2. Disconnect the door main wiring connector (A).
  3. Separate the door module (A) after removing the bolts.

    Tightening torque : 8.8 - 11,8 N·m

  4. Remove the door module after disconnecting the wiring connectors (A).
  5. Separate the wiring harness (A).
    Clip position :

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Speaker Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Speaker
  1. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim")
  2. Separate the speaker connector (A).
  3. Remove the speaker (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Switch Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Switch
  1. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim")
  2. Remove the switch (A) by pulling the hook in the direction of the arrow.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Trim Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Delta Cover
  1. Remove the cover (A).
    Clip position :
  2. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  3. Remove the delta cover.
  4. Separate the trim (A) after removing the screw.
    Clip position :
  5. Press the hook (B) and separate the rear door inside handle cage (A).
    Clip position :
  6. Remove the door trim after disconnecting the connectors (A).
    1. Disconnect the tweeter speaker connector (A).
    2. Disocnnect the rear mood lamp connector (A).
    3. Disconnect the power window switch connector (A).
Door Trim

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Weatherstrip Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Side Weatherstrip
  1. Separate the door checker (A) after removing the bolt.

    Tightening torque : 21.6 - 32 N·m

  2. Remove the weatherstrip (A).
  3. Remove the weatherstrip (A).
  4. Remove the weatherstrip (A).
    Clip position :
  5. Remove the rear door trim. (Refer to Rear Door - "Rear Door Trim")
  6. Remove the weatherstrip (A).
Door Body Side Weatherstrip Door Belt Outside Weatherstrip Door Belt Inside Weatherstrip

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Window Glass Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Window Glass
  1. Remove the rear door belt inside and outside weatherstrips. (Refer to Rear Door - "Rear Door Weatherstrip")
  2. Remove the rear door frame garnish. [Rear side] (Refer to Rear Door - "Rear Door Garnish and Molding")
  3. Separate the door channel (A) in the direction of the arrow after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

  4. Operate the power window switch to lower the window glass until the window glass bolts is visible in the service hole.
  5. remove the window glass (A) after removing the bolt.

    Tightening torque : 8.8 - 11,8 N·m

  6. Remove the door window glass.
  7. Remove the rear door frame garnish. [Front side] (Refer to Rear Door - "Rear Door Garnish and Molding")
  8. Remove the glass run (A).
Door Window Glass Run

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.

Rear Door Window Motor Removal and Installation

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
Door Window Motor
  1. Remove the rear door trim. (Refer Rear Door - "Rear Door Trim")
  2. Remove the motor connector (A).
  3. Remove the motor (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  2. Perform the window motor reset procedure. (Refer to Rear Door - "Adjustment")