How to Use Troubleshooting
PRECAUTION / NOTICE / HINT
HINT:
- Follow this procedure to troubleshoot the immobilizer system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
HINT:
- When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
- Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
- The following 5 elements are essential for analyzing the problem:
What |
Vehicle model, system name |
When |
Date, time, frequency of occurrence |
Where |
If the problem occurs at a specific location. |
What were the conditions? |
If the doors are locked or unlocked, if the engine switch is in the ON position, if the engine is running. |
How did it happen? |
Problem Symptoms |
|
PRELIMINARY CHECKS
(a) Measure the battery voltage.
Standard voltage:
11 à 14 V
If the voltage is below 11 V, charge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connectors and terminals for any abnormality, such as loose connections, deformation, etc.
|
TURN THE ENGINE SWITCH ON (IG)
NOTICE:
While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
|
CHECK CAN COMMUNICATION SYSTEM FUNCTION*
(a) Using the Techstream, check for DTCs related to the CAN communication system.
Click here
![]()
Result:
Result | Proceed to |
|---|---|
No CAN system DTCs are output |
A |
CAN-related DTCs are output |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK LIN COMMUNICATION SYSTEM COMMUNICATION FUNCTION*
(a) Using the Techstream, check for DTCs related to the LIN communication system.
Click here![]()
Result:
Result | Proceed to |
|---|---|
LIN system DTCs are not output |
A |
LIN-related DTCs are output |
B |
| B | GO TO LIN COMMUNICATION SYSTEM |
|
CHECK DTCs*
(a) Check the DTCs and record all codes output.
Body Electrical > Smart Key > Trouble Codes Powertrain > Engine and ECT > Trouble Codes(b) Based on the DTCs output above, proceed to each diagnostic procedure.
Result:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
DTCs related to the SFI system are output (without fuel vapor absorber pump module) |
B |
DTCs related to the SFI system are output (with fuel vapor absorber pump module) |
C |
DTCs related to the steering lock system are output |
D |
DTCs related to the immobilizer system are output |
E |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| C | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| D | GO TO DIAGNOSTIC TROUBLE CODE CHART |
| E | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
SYMPTOM TROUBLESHOOTING TABLE
(a) Refer to the Symptom Troubleshooting Table.
Click here![]()
Result:
Result | Proceed to |
|---|---|
The malfunction is not listed in the Problem Symptoms Table |
A |
The malfunction is listed in the Problem Symptoms Table |
B |
| B | GO TO STEP 10 |
|
GENERAL ANALYSIS AND TROUBLESHOOTING*
(a) Data List/Active Test
Click here![]()
(b) ECU Terminals
Click here![]()
|
REPAIR OR REPLACE
HINT:
When replacing the certification ECU (smart key ECU assembly), ID code box (immobilizer ECU), steering lock ECU (steering lock actuator set or upper support set), main body ECU (multiplex network body ECU), ECM or electronic key transmitter sub-assembly, refer to the registration.
|
CHECK DTCs*
(a) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs Powertrain > Engine and ECT > Clear DTCs(b) Check DTCs.
Body Electrical > Smart Key > Trouble Codes Powertrain > Engine and ECT > Trouble CodesHINT:
Before performing the DTC check, perform the "DTC Output Confirmation Check" of each diagnostic procedure.
Result:
Result | Proceed to |
|---|---|
No DTCs are output |
A |
DTCs related to the immobilizer system are output |
B |
| A | END |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |