Theft Deterrent / Keyless Entry

Engine Starter Communication Malfunction (B2779)

~6min read

DESCRIPTION

When the remote engine starter ECU does not respond to the certification ECU (Smart Key System ECU Assembly), or when the remote engine start ID code is not registered, this DTC is stored.

HINT:

The registration status of the remote engine start function ECU ID can be checked using the "Wireless C Code" item in the Data List.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2779

Engine starter communication malfunction

One of the following conditions is met (1 trip detection logic*):

  • A remote start communication error occurs.
  • No response is possible.
  • Registration has not been performed.
  • Remote engine starter ECU
  • Main body ECU (multiplex network body ECU)
  • Certification ECU (Smart Key ECU Assy)

DTC output confirmation operation:

  • A remote start operation is performed.

*: Output only when a malfunction is detected.

DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Diagnostic Condition

-

○

○

○

Malfunction Status

A remote start communication error occurs.

○

-

-

No response is possible.

-

○

-

Registration has not been performed.

-

-

○

Detection Duration

-

-

-

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

Vehicle condition and fail-safe function when a malfunction is detected

Vehicle Condition When Malfunction Is Detected

Fail-safe function when a malfunction is detected

The engine does not start with the remote start operation

The engine cannot be started by the remote start operation alone

Related Data List and Active Test

DTC No.

Data List and Active Test

B2779

  • Remote Start Communication ID
  • Remote C Code

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Before performing the check, make sure DTC B1242 (remote central door lock) is not output.
  • Before replacing the certification ECU (Smart Key System ECU Assembly) or the main body ECU (multiplex network body ECU), refer to the Registration section.

    Click here

  • After completing the repairs, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

PROCEDURE

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Check whether CAN communication system DTCs are output.

Click here

OK:

CAN communication DTCs are not output.

NG

GO TO CAN COMMUNICATION SYSTEM (DTC CHART)

OK
  1. READ VALUE USING TECHSTREAM (WIRELESS C CODE)

(a) Turn the engine switch to OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch to ON (IG).

(d) Turn on the Techstream.

(e) Select the following menus: Body Electrical / Smart Key / Data List.

(f) Read the Data List by following the Techstream instructions.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Wireless C Code

Registration status between the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

No Regd or Regd

No Regd: Remote starter ID not registered for the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

Regd: Remote starter ID registered for the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

Problems may be caused by the following conditions:

  • DTC B2779 is output.
  • Engine remote starter ECU registration has not been performed.
  • Malfunction in the certification ECU (smart key system ECU assembly) or the engine remote control ECU.
Body Electrical > Smart Key > Data List

Wireless C Code

Result:

Result

Proceed to

"No Regd" is displayed on the Techstream screen

A

"Regd" is displayed on the Techstream screen

B

B

GO TO STEP 5

A
  1. REGISTER REMOTE ENGINE START ID

(a) Register the remote engine start ID.

NEXT
  1. CHECK REMOTE ENGINE START CONTROL FUNCTION

(a) Check the remote engine start function.

OK:

The remote engine start function operates normally.

OK

END (REMOTE START ID WAS NOT REGISTERED)

NG

GO TO STEP 5

  1. REPLACE REMOTE ENGINE STARTER ECU

(a) Temporarily replace the remote engine starter ECU with a new one.

HINT:

Register the remote engine start ID.

(b) Check the remote engine start function.

OK:

The remote engine start function operates normally.

OK

END (REMOTE ENGINE STARTER ECU WAS FAULTY)

NG
  1. REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

(a) Replace the main body ECU (multiplex network body ECU) with a new one.

Click here

(b) Check the remote engine start function.

OK:

The remote engine start function operates normally.

OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS FAULTY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)