Theft Deterrent / Keyless Entry

Immobiliser System Malfunction (B2799)

~6min read

DESCRIPTION

If a communication malfunction occurs between the ECM and the ID code box (immobiliser code ECU), or if the communication ID codes do not match, the ECM stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2799

Immobiliser system malfunction

One of the following conditions is met (1 trip detection logic*):

  • A communication malfunction between the ECM and the ID code box (immobiliser code ECU).
  • A malfunction in the communication lines between the ECM and the ID code box (immobiliser code ECU).
  • A matching communication code cannot be verified during communication between the ECM and the ID code box (immobiliser code ECU).
  • ID Code Box (Immobilizer ECU)
  • ECM
  • Wire harness or connector

DTC output confirmation procedure (perform one of the following):

  • Start the engine and wait 10 seconds. If there is a malfunction, the engine stops (communication starts within 3 seconds after the engine start operation, and DTCs are stored after 6 seconds).
  • Connect a cable to the negative (-) battery terminal, start the engine and wait 10 seconds (communication starts 3 seconds after turning the engine switch to ON (IG), and DTCs are stored after 6 seconds).
  • *: Output only when a malfunction is detected.
DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Diagnostic Condition

Engine start operation.

○

○

○

Malfunction Status

A communication malfunction between the ECM and the ID code box (immobiliser code ECU).

○

-

-

A malfunction in the communication lines between the ECM and the ID code box (immobiliser code ECU).

-

○

-

A matching communication code cannot be verified during communication between the ECM and the ID code box (immobiliser code ECU).

-

-

○

Detection Duration

-

-

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

Vehicle condition and fail-safe function when a malfunction is detected

Vehicle Condition When Malfunction Is Detected

Fail-safe function when a malfunction is detected

The engine does not start.

-

Related Data List and Active Test

DTC No.

Data List and Active Test

B2799

-

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Before replacing the ECM or the ID code box (immobiliser code ECU), refer to the Registration section.

    Click here

  • After completing the repairs, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When DTC B2799 and a DTC from the certification ECU (smart key ECU assembly) are output at the same time, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

PROCEDURE

  1. REGISTER ECU COMMUNICATION ID

(a) Register the ECU communication ID code.

Click here

NEXT
  1. CLEAR DTCs

(a) Clear the DTCs.

Click here

Powertrain > Engine and ECT > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Perform the "DTC Output Confirmation" procedure.

(b) Check DTCs.

Click here

Powertrain > Engine and ECT > Trouble Codes

OK:

DTC B2799 is not output.

OK

END (COMMUNICATION ID REGISTRATION FAILED)

NG
  1. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

(a) Disconnect the F21 connector from the ID code box (immobilizer code ECU).

(b) Disconnect the A38 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F21-4 (EFIO) - A38-28 (IMI)

Always

Below 1 Ω

F21-3 (EFII) - A38-45 (IMO)

Always

Below 1 Ω

F21-4 (EFIO) or A38-28 (IMI) - Body ground

Always

10 kΩ minimum

F21-3 (EFII) or A38-45 (IMO) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

(a) Replace the ID code box (immobiliser ECU) with a new one.

Click here

NEXT
  1. REGISTER RECOGNITION CODE

(a) Register the identification codes in the ECUs.

Click here

NEXT
  1. REGISTER ECU COMMUNICATION ID

(a) Register the ECU communication ID

Click here

NEXT
  1. CHECK WHETHER THE ENGINE STARTS

(a) Make sure the engine starts.

OK:

The engine starts normally.

NG

REPLACE ECM

OK
  1. CLEAR DTCs

(a) Clear the DTCs.

Click here

Powertrain > Engine and ECT > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Perform the "DTC Output Confirmation" procedure.

(b) Check DTCs.

Click here

Powertrain > Engine and ECT > Trouble Codes

OK:

DTC B2799 is not output.

OK

END (ID CODE BOX (IMMOBILISER ECU) WAS FAULTY)

NG

REPLACE ECM