Theft Deterrent / Keyless Entry

The security indicator does not flash.

~4min read

DESCRIPTION

The Certification ECU (Smart Key ECU Assembly) flashes the Security Indicator (Combination Meter Assembly) when the Immobiliser System is activated (engine switch OFF).

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Before replacing the certification ECU (smart key ECU assy), refer to the Registration chapter.

    Click here

PROCEDURE

  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Check the DTCs.

Click here

Body Electrical > Smart Key > Trouble Codes

OK:

No DTCs are output.

NG

GO TO DIAGNOSTIC TROUBLE CODE CHART

OK
  1. PERFORM ACTIVE TEST USING TECHSTREAM (IMMOBILISER INDICATOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Smart Key / Active Test.

(e) Perform the Active Test by following the Techstream instructions.

Body Electrical > Smart Key > Active Test

Tester display

Item

Type

Diagnostic Note

Immobilizer Indicator

Immobilizer Indicator

OFF / ON

-

Body Electrical > Smart Key > Active Test

Immobilizer Indicator

OK:

The Security Indicator (Combination Meter Assembly) operates normally.

NG

GO TO STEP 4

OK
  1. CHECK SECURITY INDICATOR (COMBINATION METER ASSEMBLY)

(a) When the Immobiliser System is activated, check that the Security Indicator (Combination Meter Assembly) flashes.*1

OK:

The Security Indicator (Combination Meter Assembly) flashes normally.

(b) When the anti-theft system is in the arming standby state, check that the Security Indicator (Combination Meter Assembly) comes on.*2

OK:

The Security Indicator (Combination Meter Assembly) comes on normally.

Result:

Result

Proceed to

*1 is NG (*2 is OK)

A

*2 is NG (*1 is OK)

B

A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  1. CHECK WIRE HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR (COMBINATION METER ASSEMBLY))

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect the F81 Security Indicator (Combination Meter Assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F1-20 (IND) - F81-9 (LP)

Always

Below 1 Ω

F1-20 (IND) or F81-9 (LP) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect connector F1 of the certification ECU (smart key ECU assembly).

(b) Reconnect the F81 Security Indicator (Combination Meter Assembly) connector.

(c) Check the waveform using an oscilloscope.

*a

Component with Wire Harness Connected

(Certification ECU (smart key ECU assembly))

-

-

Measurement condition:

Tester Connection

Ignition switch position

Specified Condition

F1-20 (IND) - Body ground

Engine switch OFF → ON (IG)

Pulse generation → Less than 2 V

OK

REPLACE SECURITY INDICATOR (COMBINATION METER ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)