Theft Deterrent / Keyless Entry

Data List / Active Test

~17min read

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Smart Key / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

# Codes

Number of DTCs

0 à 255

Number of stored DTCs displayed

-

Immobilizer when IG=ON

Immobilizer system status when the engine switch is in the ON (IG) position

SET or UNSET

SET: Immobilizer system activated (driver door opened and closed with the engine switch in the ON (IG) position)

UNSET: Immobilizer system not activated when the engine switch is in the ON (IG) position, or immobilizer system deactivated 40 times after the immobilizer system was activated

-

Immobiliser

Immobilizer system status determined by the certification ECU (smart key system ECU assembly)*9

Set or Unset

Set: Immobilizer system activated (engine start disabled) (engine switch in OFF position)

Unset: Immobiliser deactivated (engine start allowed) (engine switch in ON (ACC) or ON (IG) position)

  • If "Set" is displayed, the engine start function is disabled.
  • When "Set" is displayed, the security indicator flashes.
  • The security indicator is not related to the steering lock system.

Master Key

Main key ID code match with the ID code registered in the certification ECU (smart key system ECU assembly)

MATCH or NOMATCH

Match: The main key ID code matches the ID code registered in the certification ECU (smart key system ECU assembly)

NoMatch: The main key ID code does not match the ID code registered in the certification ECU (smart key system ECU assembly)

-

Sub Key

Sub key ID code match with the ID code registered in the certification ECU (smart key system ECU assembly)

MATCH or NOMATCH

Match: The sub key ID code matches the ID code registered in the certification ECU (smart key system ECU assembly)

NoMatch: The sub key ID code does not match the ID code registered in the certification ECU (smart key system ECU assembly)

-

BCC Malfunction

Transponder chip BCC signal status*1

OK or NG

OK: BCC signal normal

NG: BCC signal malfunction (malfunction in code calculation in the electronic key transmitter sub-assembly / certification ECU (smart key system ECU assembly))

Problems may be caused by the following conditions:

  • Communication error due to wave interference (LF).
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Abnormal Status

Transponder chip status signal*1

OK or NG

OK: Transponder chip status signal normal

NG: Transponder chip status signal malfunction (malfunction in code calculation in the electronic key transmitter sub-assembly / certification ECU (smart key system ECU assembly))

Problems may be caused by the following conditions:

  • Communication error due to wave interference (LF).
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Different Encrypt Code

Transponder chip code and certification ECU (smart key system ECU assembly) code match*1

OK or NG

OK: Transponder chip and certification ECU (smart key system ECU assembly) codes match

NG: Transponder chip and certification ECU (smart key system ECU assembly) codes do not match

Problems may be caused by the following conditions:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Different Serial Number

Vehicle serial number*1

OK or NG

OK: The transponder chip signal and the vehicle serial number registered in the certification ECU (smart key system ECU assembly) match

NG: The transponder chip signal and the vehicle serial number registered in the certification ECU (smart key system ECU assembly) do not match

Problems may be caused by the following conditions:

  • An electronic key transmitter sub-assembly from a different vehicle is being used.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Frame Error

Data transmitted by the electronic key transmitter sub-assembly status

OK or NG

OK: No problem with the data transmitted by the electronic key transmitter sub-assembly

NG: There is a problem with the data transmitted by the electronic key transmitter sub-assembly

Problems may be caused by the following conditions:

  • Communication error due to wave interference.
  • The electronic key transmitter sub-assembly or the certification ECU (smart key system ECU assembly) is malfunctioning.

Response

Electronic key transmitter sub-assembly response to the certification ECU (smart key system ECU assembly) signal

OK or NG

OK: The electronic key transmitter sub-assembly responds to the certification ECU (smart key system ECU assembly) signal

NG: The electronic key transmitter sub-assembly does not respond to the certification ECU (smart key system ECU assembly) signal

Problems may be caused by the following conditions:

  • A key from a different vehicle is being used.
  • The electronic key transmitter sub-assembly, the certification ECU (smart key system ECU assembly) or the engine switch is malfunctioning.

Wireless Starter Com ID

Registration between the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

No Regd or Regd

No Regd: Registration between the engine remote starter ECU and the certification ECU (smart key system ECU assembly) not completed.

Regd: Registration between the engine remote starter ECU and the certification ECU (smart key system ECU assembly) completed

-

Wireless C Code

Registration status between the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

No Regd or Regd

No Regd: Remote starter ID not registered for the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

Regd: Remote starter ID registered for the engine remote starter ECU and the certification ECU (smart key system ECU assembly)

Problems may be caused by the following conditions:

  • DTC B2779 is output.
  • Engine remote starter ECU registration has not been performed.
  • Malfunction in the certification ECU (smart key system ECU assembly) or the engine remote control ECU.

Engine Start Condition

Engine start permission granted by the steering lock ECU (steering lock actuator assembly or upper support assembly)*2

OK or NG

OK: Engine start permitted by steering lock ECU (steering lock actuator assembly or upper support)

NG: Engine start prevented by steering lock ECU (steering lock actuator assembly or upper support)

-

ID-BOX Sleep Condition

ID Code Box (Immobiliser Code ECU) Standby Mode Status*9

Yes or No

Yes: ID Code Box (Immobiliser Code ECU) standby mode possible

No: ID Code Box (Immobiliser Code ECU) standby mode not possible

-

ID-BOX Start Condition

ID Code Box (Immobiliser Code ECU) Status*3

Yes or No

Yes: Wake-up signal transmitted by ID Code Box (Immobiliser Code ECU)

No: Wake-up signal not transmitted by ID Code Box (Immobiliser Code ECU)

-

Engine Start Request

Engine start request sent from ECM to Smart Key System ECU (smart key ECU assembly)*9

OK or NG

OK: Engine start request signal received by Smart Key System ECU (smart key ECU assembly)

NG: Engine start request signal not received by Smart Key System ECU (smart key ECU assembly)

If OK is not displayed, the immobiliser cannot be deactivated at the ECM.

3bit Code Request

3-Bit Code Request Condition

OK or NG

OK: 3-bit code request signal received

NG: 3-bit code request signal not received

-

S Code Check

S Code Verification Result*5

OK or NG

OK: S code verification result normal

NG: S code verification result abnormal

Problems may be caused by the following conditions:

  • Registration has not been performed for the Smart Key System ECU (smart key ECU assembly) or the ID Code Box (Immobiliser Code ECU).
  • The certification ECU (smart key ECU assy) or the ID code box (immobiliser code ECU) is malfunctioning.

L Code Check

L Code Verification Result*6

OK or NG

OK: L code verification result normal

NG: L code verification result abnormal

Problems may be caused by the following conditions:

  • Registration has not been performed for the ID Code Box (Immobiliser Code ECU) or the steering lock ECU (steering lock actuator assembly or upper support).
  • The ID Code Box (Immobiliser Code ECU) or the steering lock ECU (steering lock actuator assembly or upper support) is malfunctioning.

Unlock Request Receive

Steering Unlock Control Status transmitted by Smart Key System ECU (smart key ECU assembly)*7,*9

OK or NG

OK: Smart Key System ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds after the engine switch is set to ON (ACC) or ON (IG), or the engine start command is executed)

NG: Smart Key System ECU (smart key ECU assembly) does not send steering unlock command (engine switch is not set to ON (ACC) or ON (IG), and engine start operation is not performed)

If OK is not displayed even when the steering unlock conditions are met, the Smart Key System ECU (smart key ECU assembly) may be malfunctioning.

Lock Request Receive

Steering Lock Control Status transmitted by Smart Key System ECU (smart key ECU assembly)*8,*9

OK or NG

OK: Smart Key System ECU (smart key ECU assembly) sends steering lock command (within 10 seconds after a door is opened with the shift lever in P and the engine switch in OFF)

NG: Smart Key System ECU (smart key ECU assembly) does not send steering lock command (no door opened with the shift lever in P and the engine switch in OFF)

If OK is not displayed even when the steering lock conditions are met, the Smart Key System ECU (smart key ECU assembly) may be malfunctioning.

S Code Check(Past)

S Code Verification Result (Past)

OK or NG (Past)

OK: Verification confirmed (past)

NG (Past): Verification not confirmed (past)

-

L Code Check(Past)

L Code Verification Result (Past)

OK or NG (Past)

OK: Verification confirmed (past)

NG (Past): Verification not confirmed (past)

-

EFI Code Receive

Certification information sent from ECM to ID Code Box (Immobiliser Code ECU) when the ECM receives the engine start permission signal from the ID Code Box (Immobiliser Code ECU)*4, *9

OK or NG

OK: ECM immobiliser deactivation signal transmitted by ID Code Box (Immobiliser Code ECU)

NG: ECM immobiliser deactivation signal not transmitted by ID Code Box (Immobiliser Code ECU)

-

EFI Communication

Immobiliser Deactivation Communication Status between Smart Key System ECU and ECM

OK or NG

OK: Immobiliser deactivation communication has started between Smart Key System ECU (smart key ECU assembly) and ECM

NG: Immobiliser deactivation communication has not started between Smart Key System ECU (smart key ECU assembly) and ECM

If the item shows "NG", even when the immobiliser deactivation conditions have been met and the Data List item "Engine Start Request" shows "OK", there may be a malfunction in the ECM. When the engine cannot be started, use this Data List item during troubleshooting.

B Code Difference

B code mismatch

Yes or No

Yes: Communication malfunction

No: Communication normal

-

B Code

B Code Registration Status

Regd or No Regd

Regd: B code registered correctly

No Regd: B code not registered correctly

-

HINT:

  • *1: This indicates a problem with the communication format between the electronic key transmitter sub-assembly and the certification ECU (smart key ECU assembly). Possible causes include wave interference, a malfunction of the electronic key transmitter sub-assembly or the certification ECU (smart key ECU assembly), or use of an electronic key transmitter sub-assembly from a different vehicle.
  • *2: Engine start is permitted when it is confirmed that the steering lock is released and the steering lock system is not malfunctioning. If engine start is not permitted, possible causes are: a malfunction of the steering lock ECU (steering lock actuator or upper support assembly) (relay, driver side, etc.), a malfunction in the IGE circuit (wire harness or connector, ID code box (immobiliser code ECU)), or a malfunction of the steering lock sensor.
  • *3: This indicates that transmission of the wake-up signal to the transmission is possible (the "Yes" display indicates that the signal to start the LIN communication related to the verification is being transmitted). When the engine steering lock operates and an IGE signal in the ON position is received (a steering lock operation request exists), or when communication is performed between the certification ECU (smart key ECU assembly) and the ECM, the display changes to "Yes".
  • *4: This indicates that the engine start authorization request signal (EGST) from the ECM is being transmitted by the ID code box (immobiliser code ECU).
  • *5: This indicates the result of the certification of the certification codes between the certification ECU (smart key ECU assembly) and the ID code box (immobiliser code ECU).
  • *6: This indicates the result of the certification of the certification codes between the ID code box (immobiliser code ECU) and the steering lock ECU (steering lock actuator or upper support assembly).

    When the steering lock ECU (steering lock actuator or upper support assembly) receives an unlock request from the certification ECU (smart key ECU assembly), it checks the L code of the ID code box (immobiliser code ECU). If the L code matches, the steering lock ECU (steering lock actuator or upper support assembly) unlocks the steering wheel. Likewise, if the S code verification result does not match, the steering lock will not be unlocked.

  • *7: The certification ECU (smart key ECU assembly) transmits a steering unlock request for 10 seconds after the engine switch is turned to ON (ACC) or ON (IG), or when an engine start operation is performed.
  • *8: The certification ECU (smart key ECU assembly) transmits a steering lock request 10 seconds after the engine switch is turned to OFF and a door is opened with the shift lever in P.
  • *9: Refer to the following items in the Data List when checking the actual vehicle.

    With the engine switch in OFF and the shift lever in P, perform the following procedures and check the power source mode.

    • *1: Without depressing the brake pedal, press the engine switch and confirm that the power source mode changes to ON (ACC).
    • *2: While depressing the brake pedal, press the engine switch and make sure the engine starts.
    • *3: Press the engine switch and confirm that the power source mode changes to OFF.
    • *4: Open a door (the steering lock operates when a door is opened).

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Smart Key / Active Test.

(e) Perform the Active Test by following the Techstream instructions.

Body Electrical > Smart Key > Active Test

Tester display

Item

Type

Diagnostic Note

Immobilizer Indicator

Immobilizer Indicator

OFF / ON

-