Theft Deterrent / Keyless Entry

ECU Terminals

~17min read

ECU TERMINALS

INSPECT ENGINE SWITCH

(a) Measure the voltage and resistance according to the value(s) shown in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F59-6 (AGND) - Body ground

-

P - Body ground

Transponder key amplifier ground

Always

Below 1 Ω

-

F59-7 (TXCT) - F59-6 (AGND)

Input

B - P

Immobiliser communication system input

Engine switch OFF, brake pedal released, at least 30 seconds after opening and then closing the driver's door

Below 1 V

-

F59-8 (CODE) - F59-6 (AGND)

Output

L - P

Immobiliser communication system output

Engine switch OFF, brake pedal released, at least 30 seconds after opening and then closing the driver's door

Below 1 V

-

F59-10 (VC5) - F59-6 (AGND)

Input

Y - P

Transponder key amplifier power supply

Engine switch OFF, brake pedal released, at least 30 seconds after opening and then closing the driver's door

Below 1 V

-

(b) Check the pulses according to the value(s) shown in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F59-7 (TXCT) - F59-6 (AGND)

Input

B - P

Signal input from the certification ECU (smart key ECU assembly)

(Code sent from the certification ECU (smart key ECU assembly) to the transponder key amplifier built into the engine switch, then transmitted by the antenna to the transponder key amplifier as radio waves)

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

Pulse generation

(See waveform 1)

  • BCC Malfunction
  • Abnormal Status
  • Different Encrypt Code
  • Different Serial Number
  • Frame Error
  • Response

    HINT:

    If certification communication of the immobiliser key code is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above.

F59-8 (CODE) - F59-6 (AGND)

Output

L - P

Signal output to the certification ECU (smart key ECU assembly)

(Radio waves from the transponder key amplifier built into the engine switch used to detect key information. Key information sent to the certification ECU (smart key ECU assembly)).

Engine switch in OFF position, engine switch pressed and held in this position with the electronic key transmitter sub-assembly near the engine switch*

Pulse generation

(see waveform 2)

F59-10 (VC5) - F59-6 (AGND)

Input

Y - P

Transponder key amplifier power supply

(Power supplied by the certification ECU (smart key ECU assembly) when the transponder key amplifier integrated with the engine switch is activated)

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

Pulse generation

(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this check.

(c) Check the waveform using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

Measurement Condition

Item

Content

Tester Connection

F59-7 (TXCT) - F59-6 (AGND)

Oscilloscope Setting

2 V/DIV., 20 ms/DIV.

Condition

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

(2) Waveform 2 (Reference)

*a

Waveform

*b

Waveform (Detail)

Measurement Condition

Item

Content

Tester Connection

F59-8 (CODE) - F59-6 (AGND)

Oscilloscope Setting

  • Waveform

    1 V/DIV., 20 ms/DIV.

  • Waveform (Detail)

    2 V/DIV., 100 µs./DIV.

Condition

Engine switch in OFF position, engine switch pressed and held in this position with the electronic key transmitter sub-assembly near the engine switch*

HINT:

*: Remove the transmitter battery before performing this check.

(3) Waveform 3 (Reference)

Measurement Condition

Item

Content

Tester Connection

F59-10 (VC5) - F59-6 (AGND)

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Condition

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F1-4 (+B) - F1-18 (E)

Input

L - W-B

Power source +B

Always

11 à 14 V

-

F1-18 (E) - Body ground

-

W-B - Body ground

Ground

Always

Below 1 Ω

-

(c) Reconnect the F1 connector to the certification ECU (smart key ECU assembly).

(d) Measure the voltage and resistance, and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F1-17 (IG1D) - F1-18 (E)

Output

GR - W-B

Ignition power supply

Engine switch in OFF position

Below 1 V

-

Engine switch in ON (IG) position

11 à 14 V

-

F1-5 (TXCT) - F1-11 (AGND)

Output

B - P

Transponder key amplifier output signal

Engine switch OFF, brake pedal released, at least 30 seconds after opening and then closing the driver's door

Below 1 V

  • BCC Malfunction
  • Abnormal Status
  • Different Encrypt Code
  • Different Serial Number
  • Frame Error
  • Response

F1-6 (CODE) - F1-11 (AGND)

Input

L - P

Signal input from the transponder key amplifier

Engine switch OFF, brake pedal released, at least 30 seconds after opening and then closing the driver's door

Below 1 V

F1-7 (VC5) - F1-11 (AGND)

Output

Y - P

Transponder key amplifier power supply

Engine switch OFF, brake pedal released, at least 30 seconds after opening and then closing the driver's door

Below 1 V

F1-11 (AGND) - Body ground

-

P - Body ground

Transponder key amplifier ground

Always

Below 1 Ω

F1-20 (IND) - F1-18 (E)

Output

P - W-B

Security indicator output voltage

Engine switch OFF → ON (IG)

Pulse generation → Less than 2 V

-

(e) Check the pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F1-5 (TXCT) - F1-11 (AGND)

Output

B - P

Transponder key amplifier output signal

(Code sent from the certification ECU (smart key ECU assembly) to the transponder key amplifier built into the engine switch, then transmitted by the antenna to the transponder key amplifier as radio waves)

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

Pulse generation

(See waveform 1)

  • BCC Malfunction
  • Abnormal Status
  • Different Encrypt Code
  • Different Serial Number
  • Frame Error
  • Response

F1-6 (CODE) - F1-11 (AGND)

Input

L - P

Signal input from the transponder key amplifier

(Radio waves from the transponder key amplifier built into the engine switch used to detect key information. Key information sent to the certification ECU (smart key ECU assembly)).

Engine switch in OFF position, engine switch pressed and held in this position with the electronic key transmitter sub-assembly near the engine switch

HINT:

Remove the transmitter battery before performing this check.

Pulse generation

(see waveform 2)

F1-7 (VC5) - F1-11 (AGND)

Output

Y - P

Transponder key amplifier power supply

(Power supplied by the certification ECU (smart key ECU assembly) when the transponder key amplifier integrated with the engine switch is activated)

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

Pulse generation

(See waveform 3)

(f) Check the waveform using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

Measurement Condition

Item

Content

Tester Connection

F1-5 (TXCT) - F1-11 (AGND)

Oscilloscope Setting

2 V/DIV., 20 ms/DIV.

Condition

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

(2) Waveform 2 (Reference)

*a

Waveform

*b

Waveform (Detail)

Measurement Condition

Item

Content

Tester Connection

F1-6 (CODE) - F1-11 (AGND)

Oscilloscope Setting

  • Waveform

    1 V/DIV., 20 ms/DIV.

  • Waveform (Detail)

    2 V/DIV., 100 µs./DIV.

Condition

Engine switch in OFF position, engine switch pressed and held in this position with the electronic key transmitter sub-assembly near the engine switch*

HINT:

*: Remove the transmitter battery before performing this check.

(3) Waveform 3 (Reference)

Measurement Condition

Item

Content

Tester Connection

F1-7 (VC5) - F1-11 (AGND)

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Condition

Engine switch OFF, electronic key transmitter assembly not inside the cabin, within 30 seconds after pressing the engine switch

INSPECT ID CODE BOX (IMMOBILIZER CODE ECU)

(a) Disconnect the F21 connector from the ID code box (immobilizer code ECU).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F21-1 (+B) - Body ground

Input

W - Body Ground

Power source +B

Always

11 à 14 V

B2789

F21-5 (GND) - Body ground

-

W-B - Body ground

Ground

Always

Below 1 Ω

B2789

(c) Reconnect the F21 connector to the ID code box (immobilizer code ECU).

(d) Measure the voltage and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F21-3 (EFII) - F21-5 (GND)

Input

G - W-B

EFI communication system input voltage

(Signal input from the ECM to the ID code box (immobilizer code ECU))

Engine switch in OFF position

11 à 14 V

  • B2799
  • B279A
  • EFI Code Receive
  • Engine Start Request

F21-4 (EFIO) - F21-5 (GND)

Output

R - W-B

EFI communication system output voltage

(Signal output from the ID code box (immobilizer code ECU) to the ECM)

Engine switch in OFF position

11 to 14 V → Below 1 V

F21-3 (EFII) - F21-5 (GND)

Input

G - W-B

EFI communication system input voltage

(Signal input from the ECM to the ID code box (immobilizer code ECU))

Within 3 seconds of starting the engine, or within 3 seconds of turning the engine switch ON (IG) after disconnecting and reconnecting the battery cable

Pulse generation

(See waveform 1)

F21-4 (EFIO) - F21-5 (GND)

Output

R - W-B

EFI communication system output voltage

(Signal output from the ID code box (immobilizer code ECU) to the ECM)

Engine switch turned ON (IG) using the registered electronic key transmitter sub-assembly

Pulse generation

(see waveform 2)

(e) Check the waveform using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

*a

Approximately 160 ms

*b

Approximately 270 ms

Measurement Condition

Item

Content

Tester Connection

F21-3 (EFII) - F21-5 (GND)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Within 3 seconds of starting the engine, or within 3 seconds of turning the engine switch ON (IG) after disconnecting and reconnecting the battery cable

(2) Waveform 2 (Reference)

*a

Approximately 160 ms

*b

Approximately 270 ms

Measurement Condition

Item

Content

Tester Connection

F21-4 (EFIO) - F21-5 (GND)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Engine switch turned ON (IG) using the registered electronic key transmitter sub-assembly

INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSY)

(a) Measure the voltage and resistance, and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

F78-1 (GND) - Body ground

-

W-B - Body ground

Ground

Always

Below 1 Ω

-

F78-3 (IGE) - F78-1 (GND)

Input

P - W-B

Steering lock motor operation permission signal (operation permission signal sent from the certification ECU (smart key ECU assembly) to the steering lock motor)

The steering lock motor operates when all conditions are met, and then a door is opened:

  • Shift lever in P position
  • Steering unlocked
  • Engine switch in OFF position

Pulse generation

(See waveform 1)

  • Power Supply Short
  • Unlock Request Receive
  • Lock Request Receive

F78-4 (SLP1) - F78-1 (GND)

Output

G - W-B

Steering lock bar position signal (signal output from the steering unlock sensor)

Steering locked → unlocked*

11 to 14 V → Below 1.5 V

Sensor Value

F78-6 (IG2) - F78-1 (GND)

Input

B - W-B

IG signal (IG2 power input for steering lock motor)

Engine switch in OFF position

Below 1 V

B2788

Engine switch in ON (IG) position

11 à 14 V

F78-7 (B) - Body ground

Input

L - Body ground

Constant power supply

Always

11 à 14 V

B2788

HINT:

*: (The steering locks when a door is opened with the shift lever in P and the engine switch in OFF. The steering unlocks when the engine switch is turned ON (ACC).

(b) Check the waveform using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

*a

Steering lock motor does not operate

*b

Steering lock motor operates

Measurement Condition

Item

Content

Tester Connection

  • F78-3 (IGE) - F78-1 (GND)
  • F78-3 (IGE) - F78-1 (GND)

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Condition

The steering lock motor operates when all conditions are met, and then a door is opened:

  • Shift lever in P position
  • Steering unlocked
  • Engine switch in OFF position

CHECK ECM

(a) Measure the voltage and resistance, and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Corresponding Data List item/DTC

C63-59 (E1) - Body ground

-

W-B - Body ground

Ground

Always

Below 1 Ω

-

A38-45 (IMO) - C63-59 (E1)

Output

GR - W-B

ID code box (immobilizer code ECU) communication output

Engine switch in OFF position

11 à 14 V

-

A38-45 (IMO) - C63-59 (E1)

Output

GR - W-B

ID code box (immobilizer code ECU) communication output

Within 3 seconds of starting the engine, or within 3 seconds of turning the engine switch ON (IG) after disconnecting and reconnecting the battery cable

Pulse generation

(See waveform 1)

-

A38-28 (IMI) - C63-59 (E1)

Input

BE - W-B

ID code box (immobilizer code ECU) communication input

Engine switch in OFF position

11 to 14 V → Below 1 V

-

A38-28 (IMI) - C63-59 (E1)

Input

BE - W-B

ID code box (immobilizer code ECU) communication input

Engine switch turned ON (IG) using the registered electronic key transmitter sub-assembly

Pulse generation

(see waveform 2)

-

(b) Check the waveform using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

(1) Waveform 1 (Reference)

*a

Approximately 160 ms

*b

Approximately 270 ms

Measurement Condition

Item

Content

Tester Connection

A38-45 (IMO) - C63-59 (E1)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Within 3 seconds of starting the engine, or within 3 seconds of turning the engine switch ON (IG) after disconnecting and reconnecting the battery cable

(2) Waveform 2 (Reference)

*a

Approximately 160 ms

*b

Approximately 270 ms

Measurement Condition

Item

Content

Tester Connection

A38-28 (IMI) - C63-59 (E1)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Engine switch turned ON (IG) using the registered electronic key transmitter sub-assembly