Theft Deterrent / Keyless Entry

Antenna Coil Open / Short Circuit (B2784)

~5min read

DESCRIPTION

If an open or short circuit is detected in the transponder key amplifier coil built into the engine switch, the certification ECU (Smart Key System ECU Assembly) stores this DTC. This DTC is also stored as a history DTC.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2784

Antenna coil open / short circuit

When one of the following conditions is met (1 trip detection logic*1):

  • The transponder key amplifier coil built into the engine switch is open (determined by communication with the certification ECU (Smart Key System ECU Assembly)).
  • The transponder key amplifier coil built into the engine switch is shorted (determined by communication with the certification ECU (Smart Key System ECU Assembly)).
  • Engine Switch
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector

DTC output confirmation operation:

  • With the shift lever in P and the electronic key transmitter assembly held near the engine switch, an engine start operation is performed by pressing and holding the engine switch while the transmitter battery is depleted.
  • *1: Only output when a malfunction is detected.
DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

Always

○

○

Malfunction Status

The transponder key amplifier coil built into the engine switch is open (determined by communication with the certification ECU (Smart Key System ECU Assembly)).

○

-

The transponder key amplifier coil built into the engine switch is shorted (determined by communication with the certification ECU (Smart Key System ECU Assembly)).

-

○

Detection Duration

-

-

Number of Trips

1 trip(s)

1 trip(s)

Vehicle condition and fail-safe function when a malfunction is detected

Vehicle Condition When Malfunction Is Detected

Fail-safe function when a malfunction is detected

The engine cannot be started when the transmitter battery is depleted, by holding the electronic key transmitter assembly near the engine switch and pressing and holding the engine switch with the shift lever in P

-

Related Data List and Active Test

DTC No.

Data List and Active Test

B2784

-

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • Before replacing the certification ECU (smart key ECU assy), refer to the Registration chapter.

    Click here

  • After completing the repairs, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

PROCEDURE

  1. CLEAR DTCs

(a) Clear the DTCs.

Click here

Body Electrical > Smart Key > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Perform the "DTC Output Confirmation" procedure.

(b) Check DTCs.

Click here

Body Electrical > Smart Key > Trouble Codes

OK:

DTC B2784 is not output.

OK

USE SIMULATION METHOD TO CHECK

NG
  1. CHECK ENGINE SWITCH (OUTPUT)

(a) Check the waveform using an oscilloscope.

*a

Component with Wire Harness Connected

(engine switch)

*b

Waveform

*c

Waveform (Detail)

-

-

Measurement condition:

Tester Connection

Condition

Oscilloscope Setting

Specified Condition

F59-8 (CODE) - F59-6 (AGND)

Engine switch in OFF position, engine switch pressed and held in this position with the electronic key transmitter sub-assembly near the engine switch*

1 V/DIV., 20 ms/DIV.

Pulse generation

(see waveform)

2 V/DIV., 100 µs./DIV.

Pulse generation

(see waveform (detail))

  • *: Remove the transmitter battery before performing this check.

OK:

The waveform is the same as shown in the diagram

NG

REPLACE ENGINE SWITCH

OK
  1. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

(a) Replace the certification ECU (smart key ECU assy) with a new one.

Click here

NEXT
  1. REGISTER ECU COMMUNICATION ID

(a) Register the ECU communication ID code.

Click here

NEXT
  1. CLEAR DTCs

(a) Clear the DTCs.

Click here

Body Electrical > Smart Key > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Perform the "DTC Output Confirmation" procedure.

(b) Check DTCs.

Click here

Body Electrical > Smart Key > Trouble Codes

OK:

DTC B2784 is not output.

OK

END (CERTIFICATION ECU (SMART KEY SYSTEM ECU ASSEMBLY) WAS FAULTY)

NG

REPLACE ENGINE SWITCH