Body (Interior / Exterior / Electrical)

Rain Sensor Removal and Installation

7steps
~42min
2/5difficulty
010203040509.87N·mlb·ft
Tightening torque found on this page
Done 0 of 7

Removal

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  • Do not damage or touch the silicone.
  • Be careful so that the silicon is not contaminated by foreign substances, dust, etc.
  • Use caution, as the silicon may be damaged if you try to separate the rain sensor using force.
  • The dust or foreign substance on the rain sensor may have bad influence on the performance of the rain sensor therefore protect the sensor surface with the protection cover until the sensor is installed on the bracket.
  • The coupling pad on the rain sensor surface is adhesive and the coupling pad may stick to the windshield during the use depending on the environment condition.Therefore, it may be damaged when you try to remove the rain sensor from the windshield if using force. Use caution when separating it from the windshield.
  1. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal, and disconnect the high voltage service interlock connector.
    1. Open the front trunk (A).
    2. Open the auxiliary 12 V battery service cover (A).
    3. Turn the POWER OFF, separate the auxiliary battery (12 V) ( - ) terminal (A).

      Tightening torque : 7.8 - 9,8 N·m

    4. Disconnect the service interlock connector (A).
      • Wait more than 5 minutes for capacitor of the high voltage battery system to be discharged completely.
      • When working on a vehicle during discharging the capacitor, it can cause an electrical shock or injury, so follow the manual.
      The service interlock connector cannot be completely removed.
  2. Remove the multi sensor cover. (Refer to Roof Trim - "Multi Sensor Cover")
  3. Disconnect the rain sensor connector (A).
  4. Separate the rain sensor clip (A) by pulling it in the direction of the arrow.
    Clip position :
    Silicone Pad Reuse Criteria After Rain Sensor Removal and Installation Precautions (Play ▶)

    Video: Silicone Pad Reuse Criteria After Rain Sensor Removal and Installation Precautions

    Notes When Refering Video This video provides guidance for understanding complex or hard-to-follow procedures by showing each step clearly. As needed, the video also provides clear guidance on essential procedural steps, including adjustment and diagnostic processes, the use of SSTs, and precautions to avoid component damage.
    • This video is created using common specifications and may differ from the actual vehicle.
    • The location and repair procedures of the parts may vary depending on vehicle model, model year, region, and specifications.
    • Check the KDS guide for detailed information on how to use the KDS.
    • Check the manual for detailed maintenance procedures.
    • Unauthorized reproduction, distribution, or sharing of this video is prohibited.
  5. Remove the rain sensor (A).
    • Sensor may be damaged when you try to remove the rain sensor from the windshield using force. Use caution when separating it from the windshield.
    • When detaching the silicone under a high temperature, it may be easily damaged because of the adhesive strength of the silicone. Remove the silicone in a cool environment.

Installation

  • When working on the high voltage system, the work should be performed by technicians who have completed the relevant training. A lack of understanding of the high voltage system can lead to serious accidents due to electric shock or short circuit.
  • When working on the high voltage system or related components, be sure to observe and be aware of the "Safety Precautions, Cautions and Warnings". If not, it may cause serious accidents due to electric shock or short circuit.
  • When working on the high voltage system, make sure to check the Personal Protective Equipment (PPE) and high voltage shut-off procedure.
  1. Install in the reverse order of removal.
  • Push one of the latch of spring arm (A) down until it snaps and you hear a click sound and then push the latch of second spring arm (B) for keeping the sensor in right position.
  • Do not snap both spring arms at the same time.
  • An incorrectly mounted snap connection may cause malfunctions of the rain/light sensor.
  • Check the operation of the rain sensor and the light sensor before mounting.
  • Check the sensor for silicon damage.
  • Check whether the rain sensor connector is tightened.
  • Check whether the rain sensor and bracket are properly tightened.
  • Check whether the sensor mounted area is free from foreign matters.
  • Recalibrate sensitivity of the switch if the auto-wiping operation is has too little or too much sensitivity.
  • In case the silicone of the rain sensor is normal or slightly damaged as shown in the images below, it can be reused.
    Normal Damage within 1.5 mm of outer part
  • In case the silicone of the rain sensor is damaged as shown in the below images, it should be replaced with a new silicone.
    Foreign substances Fingerprint Damage

    Damage
  • The rain sensor silicone is damaged, replace it as follows.
  1. Remove the damaged silicone gel pad from the lens plate completely.
    Be careful not to damage or contaminate the surface of the lens plate during removal.
  2. Attach the new silicone gel pad after removing the silicone paper then remove the transparent film.
    When attaching the silicone gel pad to the sensor, be careful not to contaminate.
  • It is very important that the silicon (coupling pad) is completely pushed against the windshield and stuck without any air bubble.
  • In case of replacing the damaged windshield, you may reuse the undamaged existing rain sensor.
  • The windshield glass has to be clean and free of contamination or foreign substances.