Body (Interior / Exterior / Electrical)
Sunroof Assembly Removal and Installation
In this manual: Body (Interior / Exterior / Electrical)
20steps
~120min
4/5difficulty
Done 0 of 20
Removal
|
|
- Completely close the movable glass using the panorama sunroof switch.
- Remove the roof side molding. (Refer to Body Side Molding - "Roof Side Molding")
- Remove the roof shark fin antenna. (Refer to Infotainment system - "Antenna")
- Remove the moving glass. (Refer to Sunroof - "Sunroof Glass")
- Remove the bolts (A).
Tightening torque : 7.8 - 11,8 N·m
- Remove the nuts (A).
Tightening torque : 7.8 - 11,8 N·m
- Cut off the sealant of forward edge area (B) by pulling the wire (A) to the left and right.
- Put on gloves to prevent hand injuries.
- Be careful not to burn hands as the excessive heat may be generated while using the wire.
- Be careful as the wire may break when working.
- When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
- Be careful not to damage the body surface.
When using the wires, work at least the two or more people together. - Cut off the sealant on the front sealant area (A-A) while pulling the wire (B) to the left and right.
- Put on gloves to prevent hand injuries.
- Be careful not to burn hands as the excessive heat may be generated while using the wire.
- Be careful as the wire may break when working.
- When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
- Be careful not to damage the body surface.
When using the wires, work at least the two or more people together. - Cut off the sealant on the side area (A-A), while pulling the wire (B) to the left and right.
- Put on gloves to prevent hand injuries.
- Be careful not to burn hands as the excessive heat may be generated while using the wire.
- Be careful as the wire may break when working.
- When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
- Be careful not to damage the body surface.
When using the wires, work at least the two or more people together. - Cut off the sealant on the rear sealant area (A-A), while pulling the wire (B) to the left and right.
- Put on gloves to prevent hand injuries.
- Be careful not to burn hands as the excessive heat may be generated while using the wire.
- Be careful as the wire may break when working.
- When removing with a remover, use to wrap a protective tape around the tool to prevent the components from damages.
- Be careful not to damage the body surface.
When using the wires, work at least the two or more people together. - Remove the wide sunroof assembly (A) after cutting the sealant on all sides.
Be careful not to damage the wide sunroof assembly when removing it. - Cut off the remaining sealant (A) around the body panel by using the knife blade.
- Be careful not to damage the body painting surface.
- If the body painting surface is damaged, apply the repair paint or anti-corrosion agent.
When cutting off the remaining sealant of the frame, leave a thickness of 2 mm on the adhesive side.
Installation
|
- Clean the edges of the body panel and the sunroof assembly with alcohol, etc.
- Apply the body primer to the edge of the body panel and wide frame.
- Be careful not to touch the primed surface with your hands, as water leakage may occur after the sunroof assembly is installed.
- Do not smear the primer-covered surface to any foreign materials.
- After applying the primer, apply the sealant around the body panel (A) by using a sealant gun.
If the sealant is over applied and the sealant is visible outside the vehicle, clean it with alcohol or a cleaning agent. - Align to the centering device hole (A) on the body and carefully mount the wide sunroof on the body flange surface.
- Install the wide sunroof and check the flush and gaps on each side. (flush and gap conditions need to be checked by vehicle type)
Item Gap (mm) Height (mm) B-B Windshield glass - Front glass 55 - 57 0.5 - 2.5 C-C Moving glass - Body 56 - 58 -1 to 0.5 - Perform a water leak test at least 3 to 4 hours later after installing the sunroof assembly.
Keep the water stream away from directly touching the newly installed adhesive surface and let the water fall on the side of the glass. - When a leak occurs, apply the additional sealant to the leaking area.
- Allow the vehicle to stand flat for at least 4hours after installing the sunroof assembly.
- If the vehicle needs to be used, drive slowly at least for 8 hours.
- The driver should be careful to drive the vehicle aggressively or avoid uneven road driving for 2-3 days.
- Install in the reverse order of removal.
Was this page helpful?