Theft Deterrent / Keyless Entry

ECU Terminals

15steps
~90min
4/5difficulty
Done 0 of 15

ECU TERMINALS

INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disconnect connectors M66, M67 and F1 from the certification ECU (smart key ECU assembly).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Tester Connection

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Related Data List Item

M66-20 (STA) - Body ground

Input

LG - Body ground

When starting the engine, this function checks the voltage sent from the STAR terminal to the starter relay to determine whether the engine is "cranking".

20 °C

101,69 à 153,85 Ω

-

M66-9 (STAR) - Body ground

Input/Output

W - Body Ground

Outputs voltage to the starter relay coil

  • Outputs voltage (12 V) to the starter relay coil when the engine is cranking. (30 s max. Turns off when engine speed reaches 1,000 rpm.)

HINT:

When Hi is selected, a starter request signal (STAR) will not be output, even if a starter request signal (STSW) is received.

Shift lever in position other than P or N → Shift lever in P or N (at 20 °C)

10 kΩ minimum → 101.69 to 153.85 Ω

-

Receives neutral start switch signal (P, N position detection)

  • Checks whether the neutral start switch is ON (P or N) or OFF (other than P or N). Applies voltage through a (large) resistor in the certification ECU (smart key ECU assembly). When the neutral start switch is ON, due to the (low) resistance of the starter relay coil drawing part of the voltage, the STAR terminal voltage will be low (2.7 V maximum). When the neutral start switch is OFF, the voltage is high (9 V minimum).

Perform the following operations except when the engine is being started:

  • Shift lever in position other than P or N → Shift lever in P or N (at 20 °C)

30 kΩ minimum → 101.69 to 153.85 Ω

Neutral SW / Clutch SW

M66-16 (NE) - Body ground

Input

GR - Body ground

Engine Speed Signal

Always

10 kΩ minimum

Engine Condition

M67-25 (STP1) - Body ground

Input

BE - Body ground

Stop Light Switch Signal

Brake pedal depressed → Brake pedal released

9 V minimum → 1 V maximum

Stop Light

F1-4 (+B) - F1-18 (E)

Input

L - W-B

Power source

Always

11 à 14 V

-

F1-22 (P) - F1-18 (E)

Input

L - W-B

P position signal

Shift lever in P position → Shift lever in position other than P

30 kΩ minimum → Less than 200 Ω

Shift P Signal

F1-18 (E) - Body ground

-

W-B - Body ground

GND

Always

Below 1 Ω

-

F1-21 (SSW2) - Body ground

Input

GR - Body ground

SSW2 ignition switch signal

HINT:

Backup SSW1. Operates in the same manner as SSW1.

Engine switch pressed → Engine switch released

Less than 15 Ω → 10 kΩ minimum

Start Switch2

F1-23 (SSW1) - Body ground

Input

W - Body Ground

SSW1 ignition switch signal

Engine switch pressed → Engine switch released

Less than 15 Ω → 10 kΩ minimum

Start Switch1

F1-16 (ACCD) - Body ground

Output

LG - Body ground

ACC signal

20 °C

285,71 à 428,57 Ω

ACC Relay Monitor

F1-17 (IG1D) - Body ground

Output

GR - Body ground

IG signal

20 °C

60,78 à 89,11 Ω

IG Relay Monitor (Outside)

F1-19 (SPD) - Body ground

Input

V - Body ground

Vehicle speed signal

Always

30 kΩ minimum

Vehicle Speed Signal

(c) Reconnect connectors M66, M67 and F1 to the certification ECU (smart key ECU assembly).

(d) Measure the voltage and check the pulses according to the value(s) in the table below.

Tester Connection

Input/Output

Wire Color

Terminal Description

Condition

Specified Condition

Related Data List Item

M66-20 (STA) - F1-18 (E)

Input

LG - W-B

When starting the engine, this function checks the voltage sent from the STAR terminal to the starter relay to determine whether the engine is "cranking".

Engine switch held pressed with brake pedal depressed (starter in ON position) → Approximately 1 second after releasing the engine switch (starter in OFF position)

6 V or more*1 → 1.0 V or less

-

M66-9 (STAR) - F1-18 (E)

Input/Output

W - W-B

Outputs voltage to the starter relay coil

  • Outputs voltage (12 V) to the starter relay coil when the engine is cranking. (30 s max. Turns off when engine speed reaches 1,000 rpm.)

HINT:

When Hi is selected, a starter request signal (STAR) will not be output, even if a starter request signal (STSW) is received.

Engine switch held pressed with brake pedal depressed (starter in ON position) → Approximately 1 second after releasing the engine switch (starter in OFF position)

6 V or more*1 → 1.0 V or less

-

Receives neutral start switch signal (P, N position detection)

  • Checks whether the neutral start switch is ON (P or N) or OFF (other than P or N). Applies voltage through a (large) resistor in the certification ECU (smart key ECU assembly). When the neutral start switch is ON, due to the (low) resistance of the starter relay coil drawing part of the voltage, the STAR terminal voltage will be low (2.7 V maximum). When the neutral start switch is OFF, the voltage is high (9 V minimum).

Perform the following operations except when the engine is being started:

  • Shift lever in position other than P or N → Shift lever in P or N (at 20 °C)

9 V minimum → 2.7 V maximum

Neutral SW / Clutch SW

M66-16 (NE) - F1-18 (E)

Input

GR - W-B

Engine Speed Signal

At idle (engine warmed up)

Pulse generation

(See waveform 1)

Engine Condition

M67-25 (STP1) - F1-18 (E)

Input

BE - W-B

Stop Light Switch Signal

Brake pedal released → Brake pedal depressed

1 V maximum → 9 V minimum

Stop Light Switch1

F1-14 (SLP) - F1-18 (E)

Input

G - W-B

Steering lock position signal

Steering locked → Steering unlocked

11 to 14 V → 1.5 V maximum

Steering Unlock Switch

F1-25 (SLR+) - F1-18 (E)

Output

P - W-B

Steering lock motor operation signal

(Steering lock motor operation permission signal transmitted from the certification ECU (smart key ECU assembly))

When a door is opened, the steering lock motor is activated if all of the following conditions are met:

  • The steering is unlocked.
  • The engine switch is in OFF position.
  • The shift lever is in P position.

Pulse generation

(see waveform 2)

-

F1-22 (P) - F1-18 (E)

Input

L - W-B

P position signal

Shift lever in P position → Shift lever in position other than P

9 V minimum → 2.76 V maximum

Shift P Signal

F1-21 (SSW2) - F1-18 (E)

Input

GR - W-B

SSW2 ignition switch signal

HINT:

Backup SSW1. Operates in the same manner as SSW1.

Engine switch released → Engine switch pressed

9 V minimum → 1 V maximum

Start Switch2

F1-23 (SSW1) - F1-18 (E)

Input

W - W-B

SSW1 ignition switch signal

Engine switch released → Engine switch pressed

9 V minimum → 1 V maximum

Start Switch1

F1-16 (ACCD) - F1-18 (E)

Output

LG - W-B

ACC signal

Engine switch in OFF position → Engine switch in ON (ACC) position

1 V maximum → 8.5 V minimum

ACC Relay Monitor

F1-17 (IG1D) - F1-18 (E)

Output

GR - W-B

IG signal

Engine switch in ON (ACC) position → Engine switch in ON (IG) position

1 V maximum → 9 V minimum

IG Relay Monitor (Outside)

F1-19 (SPD) - F1-18 (E)

Input

V - W-B

Vehicle speed signal

Vehicle driven at approximately 5 km/h

Pulse generation

(See waveform 3)

Vehicle Speed Signal

F1-8 (CLG5) - F1-18 (E)

Output

SB - W-B

Output to interior electronic key antenna assembly No. 1 (front floor)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 4)

Overhead + Front Room (key diagnostic mode)

F1-9 (CG5B) - F1-18 (E)

Output

R - W-B

Output to interior electronic key antenna assembly No. 1 (front floor) (terminal on opposite side of CLG5 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 4)

Overhead + Front Room (key diagnostic mode)

M67-11 (CLG7) - F1-18 (E)

Output

B - W-B

Output to interior electronic key antenna assembly No. 3 (inside luggage compartment)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 4)

Overhead + Back Door (inside) (key diagnostic mode)

M67-10 (CG7B) - F1-18 (E)

Output

W - W-B

Output to interior electronic key antenna assembly No. 3 (front floor) (terminal on opposite side of CLG7 output terminal component)

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

Pulse generation

(see waveform 4)

Overhead + Back Door (inside) (key diagnostic mode)

HINT:

  • *1: When the engine is cranked, battery voltage may temporarily drop to approximately 6 V.
  • The steering lock motor actuator waveform can be checked without performing any specific operation.
  • The steering lock motor actuator waveform can be checked by performing any of the following operations:
    • To unlock the steering, bring the electronic key transmitter assembly into the cabin and set the engine switch to ON (ACC) or ON (IG).
    • To lock the steering, open a door while the engine switch is OFF and the shift lever is in P.

(e) Check the ECU waveform using an oscilloscope.

NOTICE:

The oscilloscope waveform shown in the diagram is an example for reference only. Noise, chatter, etc. are not shown.

(1) Waveform 1

Item

Content

Tester Connection

M66-16 (NE) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 2 ms/DIV.

Condition

At idle (engine warmed up)

HINT:

The higher the engine speed, the shorter the waveform cycle.

(2) Waveform 2

*a

Steering lock motor does not operate

*b

Steering lock motor operates

Item

Content

Tester Connection

F1-25 (SLR+) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 200 ms/DIV.

Condition

Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped

(3) Waveform 3

Item

Content

Tester Connection

F1-19 (SPD) - F1-18 (E)

Oscilloscope Setting

5 V/DIV., 20 ms/DIV.

Condition

Vehicle driven at approximately 5 km/h

HINT:

The higher the vehicle speed, the shorter the waveform cycle.

(4) Waveform 4

*a

For 30 seconds after closing any door

*b

At least 30 seconds after closing any door

Item

Content

Tester Connection

F1-8 (CLG5) - F1-18 (E)

F1-9 (CG5B) - F1-18 (E)

M67-11 (CLG7) - F1-18 (E)

M67-10 (CG7B) - F1-18 (E)

Oscilloscope Setting

2 V/DIV., 500 ms/DIV.

Condition

Procedure:

  1. Engine switch in OFF position
  2. Electronic key transmitter sub-assembly outside vehicle
  3. Within 30 seconds after closing any one of the doors

INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER SUPPORT ASSY)

Click here

INSPECT ID CODE BOX (IMMOBILIZER CODE ECU)

Click here

CHECK ECM

Click here

INSPECT ENGINE SWITCH

Click here