Theft Deterrent / Keyless Entry

Ignition Hold Control Malfunction (B2271)

~5min read

DESCRIPTION

This DTC is stored when a malfunction is detected in the IG circuit or IG hold circuit of the certification ECU (smart key ECU assembly).

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2271

Ignition Hold Control Malfunction

When one of the following conditions is met (1 trip detection logic*1):

  • The IG circuit of the certification ECU (smart key ECU assembly) has a malfunction.*2
  • The IG hold circuit of the certification ECU (smart key ECU assembly) has a malfunction.*3
  • AM2 Fuse
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Turn the engine switch to ON (IG).
  • *1: Only detected when a malfunction occurs and the engine switch is in ON (IG).
  • *2: The IG circuit and IG hold circuit activate the IG relay.
  • *3: Once the IG circuit is turned ON, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit keeps the power source mode in ON (IG).
DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

Turn the engine switch to ON (IG).

○

○

Malfunction Status

The IG circuit of the certification ECU (smart key ECU assembly) is not operating properly.

○

-

The IG hold circuit of the certification ECU (smart key ECU assembly) is not operating properly.

-

○

Detection Duration

-

-

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

The engine switch cannot be turned to ON (IG) (the engine cannot start).

The power source mode cannot be set to ON (IG).

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2271

Power source control
  • IG Relay Monitor (Inside)
  • Latch Circuit
Start Control
  • Ignition

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The smart key system (for engine start function) uses the LIN communication system and the CAN communication system. Check the communication function by following the procedure in the HOW TO USE TROUBLESHOOTING section. Troubleshoot the smart key system (for entry function) only after confirming that the communication systems are operating properly.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the precautions for the smart key system (for engine start function).

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When the cable is disconnected and then reconnected to the negative (-) battery terminal, the power source mode does not return to the state selected before the cable was disconnected.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

(a) Disconnect the connector from the certification ECU (smart key ECU assembly).

*a

Front view of wire harness side connector

(to certification ECU (smart key ECU assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

F1-4 (+B) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR ON POWER SOURCE CIRCUIT

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (GROUND)

(a) Disconnect the connector from the certification ECU (smart key ECU assembly).

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F1-18 (E) - Body ground

Always

Below 1 Ω

*a

Front view of wire harness side connector

(to certification ECU (smart key ECU assembly))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect connector F1 of the certification ECU (smart key ECU assembly).

*a

Component with Wire Harness Connected

(Certification ECU (smart key ECU assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F1-17 (IG1D) - Body ground

Engine switch in ON (ACC) position → Engine switch in ON (IG) position

1 V maximum → 9 V minimum

OK

END (SUSPECTED TEMPORARY CONNECTION MALFUNCTION)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)