Theft Deterrent / Keyless Entry

ACC Control Malfunction (B2274)

~6min read

DESCRIPTION

This DTC is stored when a malfunction is detected in the ACC output circuit. The ACC output circuit is the circuit between the ACCD terminal of the certification ECU (smart key ECU assembly) and the ACC relay.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2274

ACC Control Malfunction

The ACC relay circuit of the certification ECU (smart key ECU assembly) is not operating properly. (1 trip detection logic*)

HINT:

When the voltage is not at the standard ACCD value, the system is determined to be malfunctioning.

  • AM2 Fuse
  • Instrument Panel Junction Block Assembly
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Wait 10 seconds after turning the engine switch to ON (ACC) or ON (IG), and wait another 10 seconds after turning the engine switch OFF.
  • *: Detected only when a malfunction is identified.
Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

  • If a malfunction is detected due to the ACC relay being stuck ON, the ACC relay does not turn off even when the engine switch is OFF.
  • If a malfunction occurs due to the ACC relay being stuck OFF, the ACC relay does not turn on even when the engine switch is in ON (ACC).

HINT:

The engine switch can be turned to ON (IG) and the engine can start.

-

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2274

Power source control
  • ACC Relay Monitor
Start Control
  • Ignition

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The smart key system (for engine start function) uses the LIN communication system and the CAN communication system. Check the communication function by following the procedure in the HOW TO USE TROUBLESHOOTING section. Troubleshoot the smart key system (for entry function) only after confirming that the communication systems are operating properly.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the precautions for the smart key system (for engine start function).

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When the cable is disconnected and then reconnected to the negative (-) battery terminal, the power source mode does not return to the state selected before the cable was disconnected.

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR ON POWER SOURCE CIRCUIT

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (GROUND)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect connectors 3A and 3D from the instrument panel junction block assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F1-16 (ACCD) - 3A-30

Always

Below 1 Ω

3D-3 - Body Ground

Always

Below 1 Ω

F1-16 (ACCD) or 3A-30 - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

(a) Remove the instrument panel junction block assembly.

Click here

(b) Measure the resistance according to the value(s) in the table below.

*a

Component without wire harness connected

(instrument panel junction block assembly)

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

3A-30 - 3D-3

20 °C

285,71 à 428,57 Ω

3K-1 - 3A-40

Battery voltage is not applied between terminals 3A-30 and 3D-3

10 kΩ minimum

Battery voltage is not applied between terminals 3A-30 and 3D-3

Below 1 Ω

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK
  1. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect connector F1 of the certification ECU (smart key ECU assembly).

*a

Component with Wire Harness Connected

(Certification ECU (smart key ECU assembly))

(b) Reinstall the instrument panel junction block assembly.

Click here

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F1-16 (ACCD) - Body ground

Engine switch in OFF position → Engine switch in ON (ACC) position

1 V maximum → 8.5 V minimum

OK

END (SUSPECTED TEMPORARY CONNECTION MALFUNCTION)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)