Theft Deterrent / Keyless Entry

Vehicle Speed Signal Malfunction (B2282,B2283)

~8min read

DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent from the combination meter assembly via the direct line and the vehicle speed signal sent via CAN communication do not match.

DTC B2283 is stored when a malfunction is detected in the vehicle speed sensor.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2282

Vehicle speed signal malfunction

The vehicle speed signal sent from the combination meter assembly via the direct line and the vehicle speed signal sent via CAN communication do not match. (1 trip detection logic*)

  • AM2 Fuse
  • Meter / Gauge System
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Drive the vehicle at a speed of 25 km/h or higher for 20 seconds, then drive the vehicle at a speed below 5 km/h for 20 seconds.

B2283

Vehicle speed sensor malfunction

One of the following malfunctions is detected (vehicle speed sensor malfunction is detected) (1 trip detection logic*)

  • Vehicle Speed Signal Malfunction 1: Excessive deceleration detected
  • Vehicle Speed Signal Malfunction 2: Engine speed related malfunction detected
  • AM2 Fuse
  • Meter / Gauge System
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
DTC Output Confirmation Operation:
  • Run the engine at an engine speed of 2,000 rpm or higher for 300 seconds.
  • Drive the vehicle at a vehicle speed of 50 km/h or higher for 10 seconds, then drive the vehicle at a speed below 50 km/h.
  • *: Only detected when a malfunction is present and the engine switch is in the ON (IG) position.
DTC Detection Conditions (B2283)

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

  • Run the engine at an engine speed of 2,000 rpm or higher for 300 seconds.
  • Drive the vehicle at a vehicle speed of 50 km/h or higher for 10 seconds, then drive the vehicle at a speed below 50 km/h.

○

○

Malfunction Status

Excessive deceleration detected

○

-

Engine speed related detection

-

○

Detection Duration

-

-

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

DTC Code

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

B2282

  • When the signal sent via direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h, there is no effect on vehicle operation.
  • When the signal sent via direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine switch cannot be moved from the ON (IG) position to the OFF position.

-

B2283

  • The power source mode changes to OFF (engine stopped) when the engine switch is pressed while the vehicle is driving.
  • With the electronic key transmitter sub-assembly inside the cabin, the engine will not start even if the engine start operation is performed.

Operation of the steering lock motor is disabled.

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2282

B2283

Power source control
  • Vehicle Speed Signal
  • Engine Condition
  • Power Supply Condition
Start Control
  • Engine Speed
Instrument cluster
  • Vehicle Speed Meter

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The smart key system (for engine start function) uses the LIN communication system and the CAN communication system. Check the communication function by following the procedure in the HOW TO USE TROUBLESHOOTING section. Troubleshoot the smart key system (for entry function) only after confirming that the communication systems are operating properly.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the precautions for the smart key system (for engine start function).

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When the cable is disconnected and then reconnected to the negative (-) battery terminal, the power source mode does not return to the state selected before the cable was disconnected.

PROCEDURE

  1. READ THE VALUE USING TECHSTREAM (VEHICLE SPEED METER)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Combination Meter > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed Meter

Vehicle speed

Min.: 0, Max.: 255

Almost identical to actual vehicle speed (speedometer tester)

-

Body Electrical > Combination Meter > Data List

Vehicle Speed Meter

HINT:

Using a speedometer tester, check whether the actual vehicle speed and the vehicle speed displayed on the Techstream match.

OK:

The vehicle speed displayed on the Techstream is almost identical to the actual vehicle speed measured using a speedometer tester.

NG

GO TO METER / GAUGE SYSTEM (Speedometer Malfunction)

OK
  1. READ VALUE USING TECHSTREAM (VEHICLE SPEED SIGNAL)

(a) Select the following menu items: Body Electrical / Power Source Control / Data List.

(b) Read the Data List following the Techstream instructions.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed Signal

Vehicle moving or stopped

Stop or Run

Stop: Vehicle stopped

Run: Vehicle speed at or above 5 km/h

-

Body Electrical > Power Source Control > Data List

Vehicle Speed Signal

OK:

The Techstream display changes correctly according to vehicle condition.

OK

GO TO METER / GAUGE SYSTEM (HOW TO USE TROUBLESHOOTING)

NG
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR ON POWER SOURCE CIRCUIT

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (GROUND)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect the combination meter assembly connector F4.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F1-19 (SPD) - F4-6 (+S)

Always

Below 1 Ω

F1-19 (SPD) or F4-6 (+S) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect connector F1 of the certification ECU (smart key ECU assembly).

(b) Reconnect connector F4 of the combination meter assembly.

(c) Check the waveform using an oscilloscope.

*a

Component with Wire Harness Connected

(Certification ECU (smart key ECU assembly))

-

-

Tester Connection

Condition

Oscilloscope Setting

Specified Condition

F1-19 (SPD) - F1-18 (E)

Vehicle driven at approximately 5 km/h

5 V/DIV., 20 ms/DIV.

Pulse generation

HINT:

The higher the vehicle speed, the shorter the waveform cycle.

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG

GO TO METER / GAUGE SYSTEM (Vehicle Speed Signal Circuit)