Theft Deterrent / Keyless Entry

Brake Signal Malfunction (B2284)

~6min read

DESCRIPTION

This DTC is stored when the brake signal sent via the direct line and the brake signal sent via CAN communication do not match.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2284

Brake Signal Malfunction

The brake signal sent via the direct line and the brake signal sent via CAN communication do not match. (1 trip detection logic*)

  • AM2 Fuse
  • STOP fuse
  • Stop light switch assembly
  • Vehicle Stability Control System
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Connect the cable to the negative (-) battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for at least 20 seconds.
  • *: Only detected when a malfunction is present and the engine switch is in the ON (IG) position.
Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

With the electronic key transmitter assembly inside the cabin, even if an engine start operation is performed, the engine does not start (the key indicator does not appear on the multi-information display). However, the engine can be started by turning the engine switch to the ON (ACC) position, then pressing and holding it.

  • If a malfunction occurs while the brake signal sent via the direct line is ON, the engine can be started by pressing the engine switch with the brake pedal released.
  • If a malfunction occurs while the brake signal sent via the direct line is OFF, the engine cannot be started by pressing the engine switch with the brake pedal depressed.

-

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2284

Power source control
  • Stop Light Switch1
ABS / VSC / TRC / EPB
  • Stop Light SW

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The smart key system (for engine start function) uses the LIN communication system and the CAN communication system. Check the communication function by following the procedure in the HOW TO USE TROUBLESHOOTING section. Troubleshoot the smart key system (for entry function) only after confirming that the communication systems are operating properly.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the precautions for the smart key system (for engine start function).

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When the cable is disconnected and then reconnected to the negative (-) battery terminal, the power source mode does not return to the state selected before the cable was disconnected.

PROCEDURE

  1. READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH1)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Power Source Control / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Stop Light Switch1

Brake Pedal Status

OFF or ON

OFF: Brake pedal released

ON: Brake pedal depressed

  • Use this item to determine whether the malfunction is in the stop light switch assembly.
  • The engine cannot be started when this function is disabled.
  • If the stop light switch assembly is faulty, the engine can be started by pressing and holding the engine switch for a certain period of time.
Body Electrical > Power Source Control > Data List

Stop Light Switch1

OK:

The Techstream display changes correctly according to brake pedal operation.

OK

GO TO VEHICLE STABILITY CONTROL SYSTEM (HOW TO USE TROUBLESHOOTING)

NG
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR ON POWER SOURCE CIRCUIT

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (GROUND)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect connector M67 from the certification ECU (smart key ECU assembly).

(b) Disconnect connector A45 from the stop light switch assembly.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A45-7 (B) - Body ground

Always

11 à 14 V

*a

Front view of wire harness side connector

(to stop light switch assembly)

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M67-25 (STP1) - A45-3 (L)

Always

Below 1 Ω

A45-2 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect the M67 connectors of the certification ECU (smart key ECU assembly).

(b) Reconnect the A45 connector of the stop light switch assembly.

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

M67-25 (STP1) - Body ground

Brake pedal released → depressed

1 V maximum → 9 V minimum

*a

Component with Wire Harness Connected

(Certification ECU (smart key ECU assembly))

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY