Theft Deterrent / Keyless Entry

Possible Operation Signal Malfunction (B2286,P0335)

~9min read

DESCRIPTION

These DTCs are stored when the engine speed signal sent by the ECM via the direct line and the engine speed signal sent via CAN communication do not match.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2286

Possible Operation Signal Malfunction

The engine speed signal sent by the ECM via the direct line and the engine speed signal sent via CAN communication do not match. (Detection logic: 1 trip*1)

  • AM2 Fuse
  • SFI System
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Disconnect the cable from the negative (-) battery terminal, wait 30 seconds, then reconnect the cable to the negative (-) battery terminal. Wait at least 20 seconds with the engine switch in the OFF position, then start the engine and maintain an engine speed of at least 1,000 rpm for at least 20 seconds.

P0335

Crankshaft Position Sensor Circuit Malfunction (NE Signal)

The engine speed signal sent by the ECM via the direct line and the engine speed signal sent via CAN communication do not match. (Detection logic: 1 trip*1)

  • AM2 Fuse
  • SFI System
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Let the engine idle for at least 10 seconds.
  • *1: Only detected when a malfunction occurs and the engine switch is in ON (IG).
Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

  • If a malfunction occurs and the vehicle speed signal sent via the direct line or the CAN communication system indicates no speed, there is no effect on vehicle control. (A malfunction is detected after the engine switch is turned to ON (IG).)
  • If a malfunction occurs and the vehicle speed signal sent via the direct line or the CAN communication system indicates that the vehicle is moving, the engine cannot be started. However, the engine can only be started after the engine switch has been turned to OFF.
  • If a malfunction occurs and the vehicle speed signal sent via the direct line or the CAN communication system indicates no speed, there is no effect on vehicle control.
  • If the signal sent via the direct line or CAN communication malfunctions and indicates that the vehicle is moving: If the following conditions are met, the system determines that there is no malfunction in the CAN communication system but in the direct line (NE).
    • When the engine switch is pressed, the system controls the engine based on the starter OFF permission flag (ideal injection signal evaluation) via the CAN communication system, which stops engine cranking.
    • When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via CAN communication, which stops engine cranking.
    If the following conditions are met, the system determines that there is no malfunction in the direct line (NE) but in the CAN communication system.
    • When the engine switch is pressed, the system controls the engine based on the engine speed signal via the direct line, causing engine cranking to stop.
    • When the engine switch is held pressed, the system controls the engine based on the engine speed signal via the direct line, causing engine cranking to stop.
    If the following conditions are met, the system determines that there is a malfunction in the CAN communication system and in the direct line (NE).
    • When the engine switch is pressed, engine cranking stops after 6 seconds.
    • When the engine switch is pressed and held in this position, the engine is cranked for a maximum of 30 seconds.
Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2286

P0335

Power source control
  • Engine Condition
Start Control
  • Engine Speed

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The smart key system (for engine start function) uses the LIN communication system and the CAN communication system. Check the communication function by following the procedure in the HOW TO USE TROUBLESHOOTING section. Troubleshoot the smart key system (for entry function) only after confirming that the communication systems are operating properly.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the precautions for the smart key system (for start function).

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When the cable is disconnected and then reconnected to the negative (-) battery terminal, the power source mode does not return to the state selected before the cable was disconnected.

PROCEDURE

  1. READ THE VALUE USING TECHSTREAM (ENGINE CONDITION / ENGINE SPEED)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Power Source Control or Starting Control / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Engine Condition

Engine status

Stop or Run

Stop: Engine stopped

Run: Engine running

-

Body Electrical > Power Source Control > Data List

Engine Condition

Body Electrical > Starting Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Engine Speed

Engine speed

0 to 16,383 rpm

Varies according to actual engine speed

-

Body Electrical > Starting Control > Data List

Engine Speed

OK:

The Techstream display changes correctly according to the engine condition.

Result:

Result

Proceed to

OK (without fuel vapor pump module)

A

OK (with fuel vapor pump module)

B

NG

C

A

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR ON POWER SOURCE CIRCUIT

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (GROUND)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

(a) Disconnect the M66 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect the A38 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M66-16 (NE) - A38-30 (NEO)

Always

Below 1 Ω

M66-16 (NE) or A38-30 (NEO) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect the M66 connector to the certification ECU (smart key ECU assembly).

(b) Reconnect the A38 ECM connector.

(c) Using an oscilloscope, check the waveform of the engine speed input signal at the certification ECU (smart key ECU assembly) terminal.

Standard frequency:

Tester Connection

Condition

Specified Condition

M66-16 (NE) - Body ground

Engine is off

No pulse generation

Engine is running

Pulse generation

*a

Component with Wire Harness Connected

(Certification ECU (smart key ECU assembly))

Result:

Result

Proceed to

OK

A

NG (without Fuel Vapor Pump Module Absorber)

B

NG (with Fuel Vapor Pump Module Absorber)

C

A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

B

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)