Theft Deterrent / Keyless Entry

Customizable Parameters

9steps
~54min
2/5difficulty
Done 0 of 9

CUSTOMIZABLE PARAMETERS

CUSTOMIZE SMART KEY SYSTEM (for engine start function)

NOTICE:

  • When the customer requests a change to a function, first make sure that the function can be customized.
  • Record the initial settings before performing customization.

HINT:

The following items can be customized:

(a) Customizing using the Techstream

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch to ON (IG).

(3) Turn on the Techstream.

(4) Select the following menus: Customize Setting / Smart Key/Access or Warning.

(5) Select the setting by referring to the table below.

Entry / Smart Key

Tester display

Description

Default setting

Setting

ECU

Ignition Available Area

Function that sets the surface the electronic key transmitter subassembly must be on before the engine switch can be operated.

All

00: Front, 01: All

Certification ECU (Smart Key ECU Assy)

Engine Start Indicator

Function that turns the key reminder on the multi-information display ON or OFF.

ON

0 : OFF, 1 : ON

Certification ECU (Smart Key ECU Assy)

Alarm

Tester display

Description

Default setting

Setting

ECU

Key Low Battery Warning

Function that enables or disables the buzzer sound when the transmitter battery is low and the engine switch is turned OFF after being in ON (IG) for at least 20 minutes.

ON

0 : OFF, 1 : ON

Certification ECU (Smart Key ECU Assy)

(b) Open function disable (manual operation)

HINT:

While the smart key system is disabled, the doors can be locked and unlocked using the remote control, and the engine can be started by holding the electronic key transmitter subassembly close to the engine switch.

(1) The following functions are disabled when the smart key system is deactivated.

  1. Open unlock/lock functions
  2. Push-button start function
  3. Key lock-out prevention function
  4. Open warning functions

(2) When the smart key system is deactivated by manual operation:

  1. Make sure the following conditions are met:
    • The engine switch is in OFF position.
    • The driver's door is closed.
    • The driver's door is unlocked.

(3) Press the unlock switch on the electronic key transmitter sub-assembly.

(4) Open the driver's door within 5 seconds after completing the previous step (driver's door: closed → open).

(5) With the driver's door open, press the unlock switch on the electronic key transmitter subassembly twice within 5 seconds after completing the previous step.

NOTICE:

If the driver's door is closed before or during pressing of the unlock switch, the open disable setting mode stops.

(6) Perform the following procedure within 30 seconds after completing the previous step.

  1. Close and open the driver's door twice (driver's door: open → closed → open → closed → open).
  2. With the driver's door open, press the unlock switch on the electronic key transmitter sub-assembly twice.

    NOTICE:

    If the driver's door is closed before or during pressing of the unlock switch, the open disable setting mode stops.

  3. Close and open the driver's door (driver's door: open → closed → open).

(7) Close the driver's door within 5 seconds (driver's door: open → closed).

(8) Make sure that the remote buzzer sounds twice (short beeps) to confirm that the smart key system has been deactivated.

(9) Perform the following procedure to change the smart key system from deactivated to activated.

  1. Perform the procedure to deactivate the smart key system again.
  2. Make sure that the remote buzzer sounds once (short beep) to confirm that the smart key system has been reactivated.

    HINT:

    • The system changes from deactivated to activated each time the manual system deactivation procedure is performed.
    • The buzzer sounds twice when the system changes from activated to deactivated, and sounds once when the system changes from deactivated to activated.