Theft Deterrent / Keyless Entry

Operation Check

~12min read

OPERATION CHECK

NOTICE:

Make sure the smart key system (for start function) has not been disabled before performing this check.

Click here

OPERATION DESCRIPTION

(a) Push-button start function:

(1) When the electronic key transmitter assembly is inside the vehicle detection area and the brake pedal is depressed, the engine is started by pressing the engine switch.

(2) When the electronic key transmitter assembly is inside the vehicle detection area and the brake pedal is not depressed, the power source mode changes by pressing the engine switch. Each time the engine switch is pressed, the power source mode changes in the following sequence: OFF → ON (ACC) → ON (IG) → OFF.

(3) After getting into the vehicle with the electronic key transmitter assembly while the engine switch is in the OFF position, if the engine switch is pressed without depressing the brake pedal, the power supply mode changes to ON (ACC) and "ACCESSORY" is displayed on the multi-information display.

*a

"ACCESSORY" display

(4) After getting into the vehicle with the electronic key transmitter assembly while the engine switch is in the OFF position, if the engine switch is pressed twice without depressing the brake pedal, the power supply mode changes to ON (IG) and "IGNITION ON" is displayed on the multi-information display.

*a

"IGNITION ON" display

(5) After getting into the vehicle with the electronic key transmitter assembly while the engine switch is in the OFF position, if the brake pedal is depressed while the shift lever is in P, the key reminder indicator is displayed on the multi-information display.

*a

Key reminder indicator display

(6) The engine starts if the engine switch is pressed while the key reminder indicator is displayed.

(b) Change the power supply mode when the electronic key transmitter assembly does not operate properly due to radio wave interference or a discharged transmitter battery.

(1) Unlock the door using the built-in mechanical key, and enter the vehicle while carrying the electronic key transmitter assembly.

(2) While depressing the brake pedal, turn the logo side of the electronic key transmitter assembly toward the engine switch, and hold the electronic key transmitter assembly near the engine switch.

(3) A buzzer sounds from the combination meter assembly, the power supply mode changes to ON (IG), and the "IGNITION ON" message is displayed on the multi-information display.

*a

"IGNITION ON" display

(4) Pressing the engine switch without depressing the brake pedal changes the power supply mode from ON (IG) to OFF.

(c) Start the engine when the electronic key transmitter assembly does not operate properly due to radio wave interference or a discharged transmitter battery:

(1) Unlock the door using the built-in mechanical key, and enter the vehicle while carrying the electronic key transmitter assembly.

(2) While depressing the brake pedal with the shift lever in P, turn the logo side of the electronic key transmitter assembly toward the engine switch, and hold the electronic key transmitter assembly near the engine switch.

(3) A buzzer sounds from the combination meter assembly, the power supply mode changes to ON (IG), and the key reminder indicator is displayed on the multi-information display.

*a

Key reminder indicator display

(4) Press the engine switch while depressing the brake pedal to start the engine.

INSPECT PUSH BUTTON START FUNCTION

(a) To inspect the push button start function:

(1) Get into the vehicle carrying the electronic key transmitter assembly on your person, with the engine switch in the OFF position. With the shift lever in P, make sure the key reminder indicator is displayed when the brake pedal is depressed. Check whether the engine starts when the engine switch is pressed once the key reminder indicator is displayed on the multi-information display.

*a

Key reminder indicator display

(2) While carrying the electronic key transmitter assembly on your person, check whether the power supply mode changes in the following order when the engine switch is pressed and the brake pedal is released: OFF → ON (ACC) → ON (IG) → OFF.

HINT:

If the engine switch is pressed while in ON (IG) and the shift lever is in a position other than P, the power supply mode does not change to OFF but changes to ON (ACC).

(3) With the shift lever in P, make sure the steering lock is activated when a door is opened.

HINT:

When the engine switch is pressed while the vehicle is stopped, the engine stops and the power turns off. However, if the shift lever is in a position other than P when the engine switch is pressed while the vehicle is stopped, the power supply mode does not change to OFF but changes to ON (ACC).

(4) Check the operating range of the push button start function for the front side. Place the electronic key transmitter assembly at either check point so that it is oriented in the direction shown in the illustration, then make sure the engine can be started.

NOTICE:

Even if the electronic key transmitter is inside the vehicle key detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

HINT:

  • Communication may not be possible if the electronic key transmitter assembly is 0.2 m (0.656 ft) from the No. 1 interior electronic key antenna assembly (front floor).

    Click here

  • Perform this check at both check points.

*a

Check point

(5) Check the operating range of the push button start function for the rear side. Place the electronic key transmitter assembly at either check point so that it is oriented in the direction shown in the illustration, then make sure the engine can be started.

NOTICE:

Even if the electronic key transmitter is inside the vehicle key detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

HINT:

  • Communication may not be possible if the electronic key transmitter assembly is within 0.2 m (0.656 ft) of the No. 1 interior electronic key antenna assembly (front floor) or the No. 3 interior electronic key antenna assembly (luggage compartment interior).

    Click here

  • Perform this check at both check points.

*a

Check point

(6) Check the operating range of the push button start function for the luggage compartment. Place the electronic key transmitter assembly at either check point so that it is oriented in the direction shown in the illustration, then make sure the engine can be started.

NOTICE:

Even if the electronic key transmitter is inside the vehicle key detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

HINT:

  • Communication may not be possible if the electronic key transmitter subassembly is within 0.2 m (0.656 ft) of the center of the No. 3 electronic key interior antenna assembly (inside the luggage compartment).

    Click here

  • Perform this check at both check points.

*a

Check point

CHECK TRANSMITTER BATTERY SAVER MODE FUNCTION

(a) Check the transmitter battery saver mode function:

(1) Press the unlock switch on the electronic key transmitter subassembly twice while pressing the lock switch, and check that the indicator light on the electronic key transmitter subassembly flashes 4 times and enters transmitter battery saver mode.

(2) Check that the smart key system (for engine start function) does not operate when in transmitter battery saver mode.

HINT:

To cancel transmitter battery saver mode, press a switch on the electronic key transmitter.

CHECK POWER SOURCE MODE CHANGE OPERATION

(a) Check the engine switch.

(1) Check that the power source mode changes according to the table below.

Gear Engaged

Brake Pedal

Power source mode when engine switch is pressed

P

Released

Off → On (ACC) → On (IG) → Off

P

Released

Engine running → Off

P

Released

ON (ACC)* → OFF

P

Pressed

OFF → engine start

P

Pressed

ON (ACC) → engine start

P

Pressed

ON (IG) → engine start

P

Pressed

Engine running → Off

P

Pressed

ON (ACC)* → OFF

N

Released

Off → On (ACC) → On (IG) (after the power source mode changes to ON [IG], the power source mode changes from ON [IG] to ON [ACC] each time the engine switch is pressed)

N

Released

Engine running → On (ACC)

N

Pressed

OFF → engine start

N

Pressed

ON (ACC) → engine start

N

Pressed

ON (IG) → engine start

N

Pressed

Engine running → On (ACC)

Other than P or N

Released

Off → On (ACC) → On (IG) (after the power source mode changes to ON [IG], the power source mode changes from ON [IG] to ON [ACC] each time the engine switch is pressed)

Other than P or N

Released

Engine running → On (ACC)

Other than P or N

Pressed

Off → On (IG)

Other than P or N

Pressed

ON (ACC) → ON (IG)

Other than P or N

Pressed

Engine running → On (ACC)

HINT:

*: This applies only when the power source mode changes from ON (IG) to ON (ACC). (Except for emergency stop by pressing the engine switch 3 times quickly or by pressing and holding the engine switch for at least 2 seconds).

CHECK POWER SOURCE MODE INDICATION

(a) Check the key reminder display.

*a

"ACCESSORY" display

*b

"IGNITION ON" display

*c

Key reminder indicator display

-

-

Multi-information display check

Power source mode

Multi-information display

OFF

(except conditions that allow engine start)

OFF

ON (ACC)

(except conditions that allow engine start)

"ACCESSORY" is displayed

ON (IG)

(except conditions that allow engine start)

"IGNITION ON" is displayed

Condition in which engine can be started*1

Key reminder displayed

Engine started

OFF

HINT:

*1: Indicates the conditions that allow engine start by pressing the engine switch when one of the following conditions is met:

  • Condition 1

    All of the following conditions are met:

    • The power source mode has changed from ON (IG) to ON (ACC).
    • Key verification OK*2 or immobilizer disabled (engine switch in ON (ACC) or ON (IG) position).
    • Shift lever is in N and steering is unlocked.
    • Stop light switch assembly is ON.
  • Condition 2

    All of the following conditions are met:

    • The power source mode has not changed from ON (IG) to ON (ACC).
    • Key verification OK*2 or immobilizer disabled (engine switch in ON (ACC) or ON (IG) position).
    • Stop light switch assembly is ON.
    • Shift lever is in P, or shift lever is in N and steering is unlocked.

*2: When the electronic key transmitter subassembly is inside the passenger compartment, the ID code sent from the electronic key transmitter subassembly through communication is compared with the ID code calculated by the certification ECU (smart key ECU assembly). If the ID codes match, the vehicle recognizes that the electronic key transmitter subassembly is inside the passenger compartment.