Theft Deterrent / Keyless Entry

Engine / Engine Switch Malfunction (B2278)

~7min read

DESCRIPTION

This DTC is stored when the SSW1 and SSW2 contact signals, which are detected when the engine switch is operated, do not match.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2278

Engine / Power Switch Malfunction

When the engine switch is operated, the SSW1 and SSW2 contact signals do not match (1 trip detection logic*).

  • AM2 Fuse
  • Engine Switch
  • Certification ECU (Smart Key ECU Assy)
  • Wire harness or connector
  • Turn the engine switch to ON (IG).
  • *: Detected only when a malfunction is identified.
Vehicle Condition and Fail-Safe Function When Malfunction Is Detected

Vehicle Condition When Malfunction Is Detected

Fail-Safe Function When Malfunction Is Detected

If the SSW1 or SSW2 contact signal is stuck in the ON position, the power source mode cannot be changed by pressing the engine switch. If the SSW1 or SSW2 contact signal is stuck in the OFF position, the emergency stop function activated by holding the engine switch for at least 2 seconds cannot be operated.

-

Related Data List and Active Test Items

DTC No.

Data List and Active Test

B2278

Power source control
  • Starter Switch1
  • Starter Switch2

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • The smart key system (for engine start function) uses the LIN communication system and the CAN communication system. Check the communication function by following the procedure in the HOW TO USE TROUBLESHOOTING section. Troubleshoot the smart key system (for entry function) only after confirming that the communication systems are operating properly.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to the precautions for the smart key system (for engine start function).

    Click here

  • After repair, make sure no DTCs are output by performing the "DTC Output Confirmation Operation" procedure.

HINT:

When the cable is disconnected and then reconnected to the negative (-) battery terminal, the power source mode does not return to the state selected before the cable was disconnected.

PROCEDURE

  1. READ VALUE USING TECHSTREAM (START SWITCH1, START SWITCH2)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Power Source Control / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Start Switch1

Engine Start Switch 1 Status

OFF or ON

OFF: Engine start switch not pressed

ON: Engine start switch pressed

  • If the engine start switch is pressed briefly, the value shown on the screen may not change.
  • Use this item to determine whether the malfunction is in the engine start switch input signal.

Start Switch2

Engine Start Switch 2 Status

OFF or ON

OFF: Engine start switch not pressed

ON: Engine start switch pressed

  • Backup power supply for engine switch 1. However, when the engine switch is pressed and held, the power source mode can only be changed when both engine switches 1 and 2 are normal.
  • Operates in the same way as engine switch 1.
Body Electrical > Power Source Control > Data List

Tester display

Start Switch1

Start Switch2

OK:

The Techstream display changes correctly according to engine switch operation.

NG

GO TO STEP 3

OK
  1. READ VALUE USING TECHSTREAM (START SWITCH1, START SWITCH2)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Power Source Control / Data List.

(e) Based on the Techstream display, read the Data List while shaking the wire harness.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Start Switch1

Engine Start Switch 1 Status

OFF or ON

OFF: Engine start switch not pressed

ON: Engine start switch pressed

  • If the engine start switch is pressed briefly, the value shown on the screen may not change.
  • Use this item to determine whether the malfunction is in the engine start switch input signal.

Start Switch2

Engine Start Switch 2 Status

OFF or ON

OFF: Engine start switch not pressed

ON: Engine start switch pressed

  • Backup power supply for engine switch 1. However, when the engine switch is pressed and held, the power source mode can only be changed when both engine switches 1 and 2 are normal.
  • Operates in the same way as engine switch 1.
Body Electrical > Power Source Control > Data List

Tester display

Start Switch1

Start Switch2

OK:

The Techstream display changes correctly according to engine switch operation.

OK

USE SIMULATION METHOD TO CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (GROUND)

Click here

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Disconnect connector F59 from the engine switch.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F1-23 (SSW1) - F59-5 (SS1)

Always

Below 1 Ω

F1-21 (SSW2) - F59-1 (SS2)

Always

Below 1 Ω

F1-11 (AGND) - F59-6 (AGND)

Always

Below 1 Ω

F1-23 (SSW1) or F59-5 (SS1) - Body ground

Always

10 kΩ minimum

F1-21 (SSW2) or F59-1 (SS2) - Body ground

Always

10 kΩ minimum

F1-11 (AGND) or F59-6 (AGND) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT ENGINE SWITCH

(a) Remove the engine switch.

Click here

(b) Inspect the engine switch.

Click here

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG

REPLACE ENGINE SWITCH