Theft Deterrent / Keyless Entry

Data List / Active Test

~22min read

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / (desired system) / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Power Source Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Shift P Signal

P Position Engaged

OFF or ON

OFF: Shift lever in a position other than P

ON: Shift lever in P position

Use this option to determine whether the park/neutral position switch is malfunctioning.

Steering Unlock Switch

Steering unlock sensor status signal output by the steering lock ECU (steering lock actuator set or upper support)

OFF or ON

OFF: Steering locked

ON: Steering unlocked

  • When the shift lever is in P and the engine switch is in OFF, the steering is locked when a door is opened and then closed.
  • When the electronic key transmitter assembly is inside the cabin and the engine switch is set to ON (ACC) or ON (IG), the steering is unlocked.
  • The engine cannot be started when the steering unlock signal is OFF.

Stop Light Switch1

Brake Pedal Status

OFF or ON

OFF: Brake pedal released

ON: Brake pedal depressed

  • Use this item to determine whether the malfunction is in the stop light switch assembly.
  • The engine cannot be started when this function is disabled.
  • If the stop light switch assembly is faulty, the engine can be started by pressing and holding the engine switch for a certain period of time.

Start Switch1

Engine Start Switch 1 Status

OFF or ON

OFF: Engine start switch not pressed

ON: Engine start switch pressed

  • If the engine start switch is pressed briefly, the value shown on the screen may not change.
  • Use this item to determine whether the malfunction is in the engine start switch input signal.

Start Switch2

Engine Start Switch 2 Status

OFF or ON

OFF: Engine start switch not pressed

ON: Engine start switch pressed

  • Backup power supply for power supply relay 1. However, when the engine switch is held down, the control operates only when engine switches 1 and 2 are normal.
  • Operates in the same way as engine switch 1.

Neutral SW/ Clutch SW

Shift position engaged (P and N)

OFF or ON

OFF: Shift lever in a position other than P or N

ON: Shift lever in P or N

  • Use this option to determine whether the park/neutral position switch is malfunctioning.
  • When the engine cannot be started due to a malfunction of the park/neutral position switch, OFF is displayed.

Latch Circuit

Status of the backup circuits associated with ignition

OFF or ON

OFF: Engine switch in OFF

ON: Engine switch in ON (IG)

  • Operates in almost the same way as the IG relay.
  • When the engine switch is in ON (ACC) position, OFF is displayed.

Starter Request Signal

Status of the engine start request signal

OFF or ON

OFF: Engine switch not pressed

ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held down

  • When the engine cannot be started due to a malfunction of the start request signal, OFF is displayed.
  • When the engine switch is pressed, the time during which ON is displayed is very short. Therefore, the engine switch must be held down for a certain period of time.

ACC Relay Monitor

ACC relay activation

OFF or ON

OFF: Engine switch in OFF

ON: Engine switch in ON (ACC)

  • When the engine switch is in ON (IG) position, ON is displayed.
  • When the engine is started, OFF is displayed.

Engine Condition

Engine status

Stop or Run

Stop: Engine stopped

Run: Engine running

-

Vehicle Speed Signal

Vehicle moving or stopped

Stop or Run

Stop: Vehicle stopped

Run: Vehicle speed at or above 5 km/h

-

Power Supply Condition

Power Supply Status

All OFF, ACC ON, IG ON or ST ON

All OFF: Engine switch in OFF position (ACC and IG)

ACC ON: Engine start switch in ON (ACC) position

IG ON: Engine start switch in ON (IG) position

ST ON: Engine start request signal transmitted

-

Powertrain Type

Vehicle identification

HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT or S&S-MMT

Cnv-AT: Conventional A/T vehicles (without hybrid vehicle system)

-

Starter SW Sig Mismatch

The engine switch 1 and 2 signals do not match

NO or YES

No: Engine switch normal

Yes: Engine switch malfunction (the engine switch 1 and 2 signals do not match)

Even if Yes is displayed, the engine can be started. However, emergency stop while driving by pressing and holding the engine switch, and emergency start by pressing and holding the engine switch when the brakes are malfunctioning, are not possible.

Park Signal Mismatch

P position signal malfunction

NO or YES

No: Signal normal

Yes: Signal malfunction (the signals via CAN communication and the direct line do not match)

Even when Yes is displayed, the engine switch can still be set to OFF (the power supply mode is not locked in ON (ACC) or ON (IG) position).

Str Lock/Unlock Wait T-Out

Steering lock or unlock malfunction

NO or YES

No: Steering lock and unlock normal

Yes: Steering lock or unlock malfunction (for example, steering lock is stuck, etc.)

When the engine cannot be started due to a steering lock or unlock malfunction, Yes is displayed.

Key Certif Wait T-Out

Key verification malfunction

NO or YES

No: Verification normal

Yes: Verification error (detected because the ID code of the electronic key transmitter assembly and the ID code registered in the certification ECU do not match (smart key ECU assembly))

When the engine cannot be started due to a key verification error, Yes is displayed.

IG Circuit

Malfunction in the IG relay coil circuit

OK or NG

OK: Circuit normal

NG: Circuit malfunction

  • Use this item to determine whether the malfunction is in the IG relay.
  • When the engine cannot be started due to a malfunction of the IG relay, NG is displayed.

IG Relay Monitor (Outside)

IG relay coil voltage monitor status

OFF or ON

OFF: Engine switch in OFF

ON: Engine switch in ON (IG)

  • Use this item to determine whether the malfunction is in the IG relay.
  • When the engine switch is in ON (ACC) position, OFF is displayed.

IG Relay Monitor (Inside)

IG relay activation

OFF or ON

OFF: Engine switch in OFF

ON: Engine switch in ON (IG)

  • Use this item to determine whether the malfunction is in the IG relay.
  • When the engine switch is in ON (ACC) position, OFF is displayed.

Number of Diagnosis Code

Number of DTCs

0 à 255

-

-

To check whether the Data List display changes, enter the vehicle while carrying an electronic key transmitter assembly and perform the following when the engine switch is OFF and the shift lever is in P.

HINT:

*1: Press the engine switch with the brake pedal released, and check that the engine switch changes to ON (ACC).

*2: Press the engine switch with the brake pedal released, and check that the engine switch changes to ON (IG).

*3: Depress the brake pedal (stop light switch assembly in ON position).

*4: Press the engine switch while depressing the brake pedal, and check that the engine starts.

*5: Press the engine switch with the brake pedal depressed, and check that the engine switch changes to OFF.

*6: Release the brake pedal.

*7: Open one of the doors.

Body Electrical > Smart Key > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Key Low Battery

Transmitter Battery Discharged

NO or YES

No: Transmitter battery not discharged

Yes: Transmitter battery discharged

The electronic key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it transmits. "Yes" is displayed for the "Key Low Battery" Data List item when the voltage information indicates a value of 2.2 V or less. This Data List item must be checked when the electronic key transmitter sub-assembly is at cabin temperature (for example, at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).

# Codes

Number of DTCs

0 à 255

-

-

Immobiliser

Immobiliser system status determined by the certification ECU (smart key ECU assembly)

Set or Unset

Set: Immobiliser activated (engine start disabled) (engine switch in OFF position)

Unset: Immobiliser deactivated (engine start allowed) (engine switch in ON (ACC) or ON (IG) position)

The engine cannot be started when Setting is displayed.

HINT:

  • The security indicator lights up when Setting is displayed.
  • The security indicator is linked to the activation/deactivation of the immobilizer system and is not linked to the steering lock/unlock.

Steering Lock Sleep Cond

Steering lock ECU standby availability

NO or YES

No: Sleep not available

Yes: Sleep available

-

Steering Lock Start Cond

Steering lock ECU activation signal status

NO or YES

No: Activation signal not sent

Yes: Activation signal sent

-

Engine Start Condition

Status of the engine start permission signal determined by the steering lock ECU (steering lock actuator or upper support assembly) and sent to the certification ECU (smart key ECU assembly)

NG or OK

NG: Engine start inhibited

OK: Engine start permitted

  • When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator or upper support assembly), allowing the engine to start.
  • The engine cannot start when NG is displayed.

Sensor Value

Steering lock ECU (upper support assembly or steering lock actuator) position sensor malfunction history (DTC B2781 is stored)

OK or NG (Past)

OK: No malfunction history of the steering lock ECU (upper support assembly or steering lock actuator) lock or unlock sensor.

NG (Past): Malfunction history exists for both the lock and unlock sensors in the steering lock ECU (upper support assembly or steering lock actuator) being ON. (Under normal operating conditions, the sensor is not ON.)

If NG (Past) is displayed, there may be a malfunction in either the steering lock ECU position sensor (steering lock actuator or upper support assembly) or the assembly itself.

Power Supply Short

Signal error (short circuit) history sent from the certification ECU (smart key ECU assembly) to the steering lock ECU (upper support assembly or steering lock actuator) (DTC B2782 is stored)

OK or NG (Past)

OK: No short-circuit history of the motor power supply.

NG (Past): Short-circuit history of the motor power supply exists.

This item displays history when a malfunction exists in the circuit between the certification ECU (smart key ECU assembly) and the steering lock ECU (steering lock actuator or upper support assembly).

Motor Driver Short

Malfunction history (short circuit) in the motor circuit of the steering lock ECU (upper support assembly or steering lock actuator) (DTC B2781 is stored)

OK or NG (Past)

OK: No short-circuit history in the electric motor circuit.

NG (Past): Short-circuit history in the motor circuit exists.

This item displays the malfunction history of the motor circuit of the steering lock ECU (steering lock actuator or upper support assembly).

Lock/Unlock Receive

Unlock request signal reception history

NO or YES

No: No unlock request signal reception history exists.

Yes: Unlock request signal reception history exists.

-

Lock Bar Stuck Error

Steering wheel lock malfunction history during steering lock operation for a certain period

OK or NG (Past)

OK: No steering wheel locked history.

NG (Past): Steering wheel locked history exists.

-

Engine Start Request

Immobilizer deactivation signal (engine start permitted) status sent from the certification ECU (smart key ECU assembly) and received by the ID code box (immobilizer code ECU)

OK or NG

OK: Signal received

NG: Signal not received

  • The ID code box (immobilizer code ECU) receives the immobilizer deactivation signal (engine start permitted) sent by the certification ECU (smart key ECU assembly) and permits fuel injection and ignition when OK is displayed.
  • The engine cannot start when NG is displayed.

S Code Check

Verification result between the certification ECU (smart key ECU assembly) and the ID code box (immobilizer ECU)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When NG is displayed:

  • The ID code is not registered for the certification ECU (smart key ECU assembly) or the ID code box (immobilizer code ECU), or the certification ECU (smart key ECU assembly) or the ID code box (immobilizer code ECU) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).

L Code Check

Verification result between the ID code box (immobilizer ECU) and the steering lock ECU (steering lock actuator assembly or upper support assembly)

OK or NG

OK: Verification result normal

NG: Verification result abnormal

When NG is displayed:

  • The ID code of the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is not registered, or the ID code box (immobilizer ECU) or the steering lock ECU (steering lock actuator assembly or upper support assembly) is faulty.
  • The steering cannot be locked.
  • The steering cannot be unlocked (the engine cannot start).

Unlock Request Receive

Unlock request signal received status

OK or NG

OK: Unlock request signal received within 10 seconds after the engine switch is turned to ON (IG) or ON (ACC), or after an engine start operation.

NG: The engine switch is not in ON (IG) or ON (ACC) and no engine start operation has been performed.

  • The engine cannot start when an unlock request signal cannot be received.
  • If OK is not displayed even when the steering lock conditions are met, the Smart Key System ECU (smart key ECU assembly) may be malfunctioning.

Lock Request Receive

Lock request signal received status

OK or NG

OK: Lock request signal received within 10 seconds of opening any door with the shift lever in P* and the engine switch in OFF.

NG: Other than the above

If OK is not displayed even when the steering lock conditions are met, the Smart Key System ECU (smart key ECU assembly) may be malfunctioning.

S Code Check(Past)

Verification result history between the certification ECU (smart key ECU assembly) and the ID code box (immobilizer code ECU)

OK or NG (Past)

OK: No abnormal verification result history.

NG (Past): Abnormal verification result history exists.

-

L Code Check(Past)

Verification result history between the ID code box (immobilizer code ECU) and the steering lock ECU (steering lock actuator or upper support assembly)

OK or NG (Past)

OK: No abnormal verification result history.

NG (Past): Abnormal verification result history exists.

-

Steering Lock

Lock confirmation status of the steering lock ECU (steering lock actuator or upper support assembly)

Unset or Set

Unset: Lock not confirmed

Set: Lock confirmed

When Unset is displayed, the steering is not locked.

Steering Unlock

Unlock confirmation status of the steering lock ECU (steering lock actuator or upper support assembly)

Unset or Set

Unset: Unlock not confirmed

Set: Unlock confirmed

When Unset is displayed, the steering is locked (the engine cannot start).

Engine Start Indicator

Key reminder indicator display

OFF or ON

Customised setting displayed

-

Open in IG2

IG2 input history of the steering lock ECU (steering lock actuator or upper support assembly)

OK or NG (Past)

OK: No open-circuit history in the IG2 terminal circuit.

NG (Past): Open-circuit history exists in the IG2 terminal circuit.

When "OK" is displayed, the steering lock ECU (steering lock actuator or upper support assembly) has a malfunction in the IG2 input circuit.

To check whether the Data List display changes, enter the vehicle while carrying an electronic key transmitter assembly and perform the following when the engine switch is OFF and the shift lever is in P.

HINT:

*1: Press the engine switch with the brake pedal released, and check that the engine switch changes to ON (ACC).

*2: Press the engine switch with the brake pedal released, and check that the engine switch changes to ON (IG).

*3: Press the engine switch and make sure the engine switch is in the OFF position.

*4: Release the brake pedal, open the driver's door and confirm that the steering locks.

Body Electrical > Starting Control > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Starter SW

Starter Operation Request

OFF or ON

OFF: Starter activation not requested

ON: Starter activation requested

When OFF is displayed, the engine is not being cranked.

Shift Position P or N

Park/Neutral Position Switch Status

OFF or ON

OFF: Shift lever in a position other than P or N

ON: Shift lever in P or N

When OFF is displayed, the engine is not being cranked.

Starter Relay

Starter Relay Voltage Check

OFF or ON

OFF: ST relay in OFF position

ON: ST relay in ON position

When OFF is displayed, the engine cannot be cranked.

Starting Control SW

Starter Request Signal Check

OFF or ON

OFF: Starting control switch in OFF position

ON: Starting control switch in ON position

When OFF is displayed, the engine cannot be cranked.

Ignition

IG2 status

OFF or ON

OFF: IG2 relay in OFF position

ON: IG2 relay in ON position

-

Engine Speed

Engine speed

0 to 16,383 rpm

Varies according to actual engine speed

-

Number of DTCs

Number of DTCs

0 à 255

-

-

HINT:

*: With the engine switch in ON (IG) mode, the shift lever in P and the brake pedal depressed, press the engine switch and make sure the engine starts.

Body Electrical > Combination Meter > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed Meter

Vehicle speed

Min.: 0, Max.: 255

Almost identical to actual vehicle speed (speedometer tester)

-

Chassis > ABS/VSC/TRC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Stop Light SW

Stop light switch

OFF or ON

OFF: Brake pedal released

ON: Brake pedal depressed

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch to ON (IG).

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / (desired system) / Active Test.

(e) Perform the Active Test by following the instructions shown on the Techstream screen.

Body Electrical > Power Source Control > Active Test

Tester display

Item

Control Range

Diagnostic Note

P Supply for Steering Lock

Certification ECU (Smart Key ECU Assy)

OFF / ON

HINT:

OFF: Power is not supplied.

ON: Power is supplied.

When performing the Active Test, make sure the following condition is met:

The engine switch is in the ON (IG) position.

Body Electrical > Smart Key > Active Test

Tester display

Item

Control Range

Diagnostic Note

Power/Engine SW Light

Engine Switch Light

OFF / ON

When performing the Active Test, make sure the following conditions are met:

The engine switch light is off (at least 15 seconds have passed since it was switched off) and the engine switch is in ON (ACC) or ON (IG) mode, or the engine is running.

Body Electrical > Starting Control > Active Test

Tester display

Item

Control Range

Diagnostic Note

Activate the Starter Relay

ST Relay

OFF / ON

When performing the Active Test, make sure the following conditions are met:

The electronic key transmitter sub-assembly is inside the cabin and the engine is stopped.