Camshaft Position "A" Actuator Circuit (Bank 1) (P0010,P0020)
In this manual: Engine, Hybrid System
12steps
~72min
3/5difficulty
Done 0 of 12
DESCRIPTION
This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
The VVT (variable valve timing) system adjusts the intake and exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
DTC No.
DTC Detection Condition
Trouble Area
P0010
Open or short in OCV (for intake side of bank 1) circuit
(1 trip detection logic)
Open or short in OCV (for intake side of bank 1) circuit
OCV (for intake side of bank 1)
ECM
P0020
Open or short in OCV (for intake side of bank 2) circuit
(1 trip detection logic)
Open or short in OCV (for intake side of bank 2) circuit
OCV (for intake side of bank 2)
ECM
HINT:
This DTC relates to the Oil Control Valve (OCV).
MONITOR DESCRIPTION
This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
MONITOR STRATEGY
Related DTCs
P0010: VVT OCV range check (Bank 1)
P0020: VVT OCV range check (Bank 2)
Required Sensors/Components (Main)
VVT OCV
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
All
Monitor runs whenever following DTCs not present
None
All of following conditions met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
0.5 seconds or more
Case 1
One of following conditions met
-
A. All of following conditions met
-
Battery voltage
11 to 13 V
Target duty ratio
Less than 70%
B. All of following conditions met
-
Battery voltage
13 V or more
Target duty ratio
Less than 80%
Case 2
Current cut status
Not cut
TYPICAL MALFUNCTION THRESHOLDS
Case 1
Output duty cycle
100% or more
Case 2
Output duty cycle
3% or less
COMPONENT OPERATING RANGE
VVT OCV duty cycle
3 to 100%
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Wait 5 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0010 or P0020.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
PROCEDURE
CHECK FOR DTC
(a) Clear DTCs after recording the freeze frame data and DTCs (See page ).
(b) Turn the ignition switch off.
(c) Allow the engine to idle and check for DTCs.
(d) Check that P0010 or P0020 is not present.
OK:
P0010 or P0020 is not present.
OK
CHECK FOR INTERMITTENT PROBLEMS
NG
INSPECT CAMSHAFT OIL CONTROL VALVE
(a) Disconnect the OCV connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20 °C
6.9 to 7.9 Ω
NG
REPLACE CAMSHAFT OIL CONTROL VALVE
OK
CHECK HARNESS AND CONNECTOR (OCV - ECM)
(a) Disconnect the OCV connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.