Open in Secondary Air Injection System Heater Control Circuit (P144C,P144D)
In this manual: Engine, Hybrid System
14steps
~84min
4/5difficulty
Done 0 of 14
DESCRIPTION
The ECM operates the air pump heater (AI HTR) relay which causes the air pump heater (AI HTR) to operate.
DTC No.
DTC Detection Condition
Trouble Area
P144C
Open or short in the air pump heater (AI HTR) relay circuit for 5 seconds (1 trip detection logic).
Open or short in air pump heater (AI HTR) relay circuit
Air pump heater (AI HTR) relay
ECM
P144D
Open or short in the air pump heater (AI HTR) relay circuit for 5 seconds (1 trip detection logic).
Open or short in air pump heater (AI HTR) relay circuit
Air pump heater (AI HTR) relay
ECM
MONITOR DESCRIPTION
These DTCs are designed to detect a malfunction in the air pump heater (AI HTR) relay circuit. When the system is normal, the battery voltage is applied to terminal HAI1 of the ECM while the air pump heater (AI HTR) relay is turned off, and the battery voltage is not applied to terminal HAI1 of the ECM while the air pump heater (AI HTR) relay is turned on. The ECM illuminates the MIL and stores a DTC when either one of the following conditions is detected.
The battery voltage is not applied to terminal HAI1 while the air pump heater (AI HTR) relay is off.
The battery voltage is applied to terminal HAI1 while the air pump heater (AI HTR) relay is on.
MONITOR STRATEGY
Related DTCs
P144C: Air pump heater relay circuit range check (Low voltage)
P144D: Air pump heater relay circuit range check (High voltage)
Required Sensors/Components (Main)
Air pump heater relay (AI HTR)
Required Sensors/Components (Related)
-
Frequency of operation
Continuous
Duration
5 seconds
MIL operation
Immediate
Sequence of operation
None
TYPICAL ENABLING CONDITIONS
Case 1
Monitor runs whenever following DTCs not stored
None
Current air pump heater relay (AI HTR)
ON
Last air pump heater (AI HTR) relay
ON
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
Case 2
Monitor runs whenever following DTCs not stored
None
Current air pump heater (AI HTR) relay
OFF
Last air pump heater (AI HTR) relay
OFF
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
TYPICAL MALFUNCTION THRESHOLDS
P144C
Air pump heater (AI HTR) relay output terminal voltage
Low
P144D
Air pump heater (AI HTR) relay output terminal voltage
High
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Wait for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.
Activate the air pump heater for 10 seconds or more.
HINT:
The active test activates the air pump heater for up to 60 seconds.
To protect the air pump heater, do not perform this test more than 4 times in a row.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read Pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P144C or P144D.
Check the DTC judgment result.
Techstream Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If no permanent DTC is output, the system is normal.
If a permanent DTC is output, the system is malfunctioning.
WIRING DIAGRAM
Refer to DTC P0412 (See page ).
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
INSPECT AIR PUMP HEATER (AI HTR) RELAY
(a) Remove the air pump heater (AI HTR) relay from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied
10 kΩ or higher
Battery voltage applied to terminals 1 and 2
Below 1 Ω
NG
REPLACE AIR PUMP HEATER (AI HTR) RELAY
OK
CHECK AIR PUMP HEATER (AI HTR) RELAY (POWER SOURCE)
(a) Remove the air pump heater (AI HTR) relay from the engine room relay block.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
2 (Air pump heater (AI HTR) relay) - Body ground
Always
11 to 14 V
Text in Illustration
*1
Engine Room Relay Block
*2
Air Pump Heater (AI HTR) Relay
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (ECM - AIR PUMP HEATER (AI HTR) RELAY)
(a) Remove the air pump heater (AI HTR) relay from the engine room relay block.
(b) Disconnect the D74 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.