Ignition Coil "A" Primary / Secondary Circuit (P0351-P0358)
In this manual: Engine, Hybrid System
13steps
~78min
3/5difficulty
Done 0 of 13
DESCRIPTION
HINT:
These DTCs indicate malfunctions relating to the primary circuit.
If DTC P0351 is stored, check the No. 1 ignition coil circuit.
If DTC P0352 is stored, check the No. 2 ignition coil circuit.
If DTC P0353 is stored, check the No. 3 ignition coil circuit.
If DTC P0354 is stored, check the No. 4 ignition coil circuit.
If DTC P0355 is stored, check the No. 5 ignition coil circuit.
If DTC P0356 is stored, check the No. 6 ignition coil circuit.
If DTC P0357 is stored, check the No. 7 ignition coil circuit.
If DTC P0358 is stored, check the No. 8 ignition coil circuit.
A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
P0357
P0358
No IGF signal to ECM while engine running
(1 trip detection logic)
Ignition system
Open or short in IGF or IGT circuit (1 to 8) between ignition coil and ECM
No. 1 to No. 8 ignition coils
ECM
Reference: Inspection using an oscilloscope.
Standard:
Tester Connection
Tool Setting
Condition
Specified Condition
D74-40 (IGT1) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-33 (IGT2) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-37 (IGT3) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-34 (IGT4) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-35 (IGT5) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-36 (IGT6) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-38 (IGT7) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-39 (IGT8) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-104 (IGF1) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
D74-105 (IGF2) - D74-81 (E1)
2 V/DIV., 20 msec./DIV.
Idling
The correct waveform is as shown
HINT:
While cranking or idling the engine, check the waveform between terminals IGT (1 to 8) and E1, and IGF1 or IGF2 and E1 of the ECM connector.
MONITOR DESCRIPTION
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.
MONITOR STRATEGY
Related DTCs
P0351: Igniter (cylinder 1) malfunction
P0352: Igniter (cylinder 2) malfunction
P0353: Igniter (cylinder 3) malfunction
P0354: Igniter (cylinder 4) malfunction
P0355: Igniter (cylinder 5) malfunction
P0356: Igniter (cylinder 6) malfunction
P0357: Igniter (cylinder 7) malfunction
P0358: Igniter (cylinder 8) malfunction
Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
0.256 seconds
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Either of following conditions A or B met
-
A. Engine RPM
1500 rpm or less
B. Starter
OFF
Either of following conditions C or D met
-
C. Both of following conditions (a) and (b) met
-
(a) Engine speed
500 rpm or less
(b) Battery voltage
6 V or more
D. All of following conditions (a), (b) and (c) met
-
(a) Engine speed
More than 500 rpm
(b) Battery voltage
10 V or more
(c) Number of sparks after CPU reset
5 sparks or more
TYPICAL MALFUNCTION THRESHOLDS
All of the following conditions are met
A. B. C and D
A. Ignition signal fail counter
More than 2 times
B. Time after condition A is met
0.256 seconds or more
C. Ignition signal fail count after condition B is met
More than 2 times
D. Ignition switch
ON
COMPONENT OPERATING RANGE
IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 10 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0351, P0352, P0353, P0354, P0355, P0356, P0357 or P0358.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
(a) Disconnect the ignition coil assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D10-4 (GND) - Body ground
Always
Below 1 Ω
D25-4 (GND) - Body ground
Always
Below 1 Ω
D12-4 (GND) - Body ground
Always
Below 1 Ω
D23-4 (GND) - Body ground
Always
Below 1 Ω
D14-4 (GND) - Body ground
Always
Below 1 Ω
D21-4 (GND) - Body ground
Always
Below 1 Ω
D16-4 (GND) - Body ground
Always
Below 1 Ω
D91-4 (GND) - Body ground
Always
Below 1 Ω
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D10-1 (+B) - D10-4 (GND)
Ignition switch ON
11 to 14 V
D25-1 (+B) - D25-4 (GND)
Ignition switch ON
11 to 14 V
D12-1 (+B) - D12-4 (GND)
Ignition switch ON
11 to 14 V
D23-1 (+B) - D23-4 (GND)
Ignition switch ON
11 to 14 V
D14-1 (+B) - D14-4 (GND)
Ignition switch ON
11 to 14 V
D21-1 (+B) - D21-4 (GND)
Ignition switch ON
11 to 14 V
D16-1 (+B) - D16-4 (GND)
Ignition switch ON
11 to 14 V
D91-1 (+B) - D91-4 (GND)
Ignition switch ON
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
(a) Disconnect the ignition coil assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.