Camshaft Position Sensor Circuit (P0340,P0342,P0343,P0345,P0347,P0348)
In this manual: Engine, Hybrid System
13steps
~78min
3/5difficulty
Done 0 of 13
DESCRIPTION
The intake camshaft's Variable Valve Timing (VVT) sensor (VV1 and VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).
The intake camshaft has a sensor plate with 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the gear rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P0340
P0345
No VVT sensor signal to ECM at engine speed of 600 rpm or more
(1 trip detection logic)
Open or short in VVT sensor (for intake side of bank 1, 2) circuit
VVT sensor (for intake side of bank 1, 2)
Intake camshaft
Timing chain for intake camshaft jumped tooth
ECM
P0342
P0347
Output voltage of VVT sensor less than 0.3 V for 4 seconds
(1 trip detection logic)
Open or short in VVT sensor (for intake side of bank 1, 2) circuit
VVT sensor (for intake side of bank 1, 2)
Intake camshaft
Timing chain for intake camshaft jumped tooth
ECM
P0343
P0348
Output voltage of VVT sensor more than 4.7 V for 4 seconds
(1 trip detection logic)
Open or short in VVT sensor (for intake side of bank 1, 2) circuit
VVT sensor (for intake side of bank 1, 2)
Intake camshaft
Timing chain for intake camshaft jumped tooth
ECM
Reference: Inspection using an oscilloscope
Standard:
Tester Connection
Tool Setting
Condition
Specified Condition
D74-110 (NE+) - D74-111 (NE-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
D74-92 (VV1+) - D74-91 (VV1-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
D74-87 (VV2+) - D74-88 (VV2-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
HINT:
VV1 and VV2 are the VVT sensor signals, and NE is the CKP sensor signal.
MONITOR DESCRIPTION
If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.
When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.
MONITOR STRATEGY
Related DTCs
P0340: VVT position sensor (for Bank 1) verify pulse input
P0342: VVT position sensor (for Bank 1) range check (low voltage)
P0343: VVT position sensor (for Bank 1) range check (high voltage)
P0345: VVT position sensor verify pulse input (for Bank 2)
P0347: VVT position sensor (for Bank 2) range check (low voltage)
P0348: VVT position sensor (for Bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT position sensor (for Bank 1 and 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
P0340, P0345: 5 seconds
P0342, P0343, P0347, P0348: 4 seconds
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
P0340, P0345 (Verify pulse input):
Engine speed
600 rpm or more
Battery voltage
8 V or higher
Starter
OFF
Ignition switch
ON
Camshaft position sensor voltage
0.3 to 4.7 V
VVT sensor range check low voltage fail (P0342, P0347)
Not detected
VVT sensor range check high voltage fail (P0343, P0348)
Not detected
P0342, P0343, P0347, P0348 (Low voltage, High voltage):
Starter
OFF
Ignition switch
ON
Ignition switch ON and time after ignition switch is off to ON
2 seconds or more
VVT sensor verify pulse input fail (P0340, P0345)
Not detected
Battery voltage
8 V or Higher
TYPICAL MALFUNCTION THRESHOLDS
P0340, P0345 (Verify pulse input):
VVT sensor signal
No signal
P0342, P0347 (Low voltage):
VVT sensor voltage
Below 0.3 V
P0343, P0348 (High voltage):
VVT sensor voltage
Higher than 4.7 V
COMPONENT OPERATING RANGE
VVT sensor voltage
0.3 to 4.7 V
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 10 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
PROCEDURE
CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
(a) Disconnect the VVT sensor (for intake side) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
3 (VC) - Body ground
Ignition switch ON
4.5 to 5.0 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE SIDE - ECM)
(a) Disconnect the VVT sensor (for intake side) connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D37-1 (VVL+) - D74-92 (VV1+)
Always
Below 1 Ω
D37-2 (VVL-) - D74-91 (VV1-)
Always
Below 1 Ω
D39-1 (VVR+) - D74-87 (VV2+)
Always
Below 1 Ω
D39-2 (VVR-) - D74-88 (VV2-)
Always
Below 1 Ω
D37-1 (VVL+) or D74-92 (VV1+) - Body ground
Always
10 kΩ or higher
D37-2 (VVL-) or D74-91 (VV1-) - Body ground
Always
10 kΩ or higher
D39-1 (VVR+) or D74-87 (VV2+) - Body ground
Always
10 kΩ or higher
D39-2 (VVR-) or D74-88 (VV2-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE SIDE)
(a) Check the VVT sensor (for intake side) installation.
OK:
Sensor is installed correctly.
NG
SECURELY REINSTALL SENSOR
OK
INSPECT INTAKE CAMSHAFT (TEETH)
(a) Check the teeth of the camshaft.
OK:
Teeth do not have any cracks or deformation.
HINT:
Perform "Inspection After Repair" after replacing the intake camshaft (See page ).
NG
REPLACE INTAKE CAMSHAFT
OK
CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)
NG
ADJUST VALVE TIMING
OK
REPLACE VVT SENSOR (FOR INTAKE SIDE)
(a) Replace the VVT (for intake side) sensor (See page ).
NEXT
CHECK WHETHER DTC OUTPUT RECURS
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear DTCs.
(e) Refer to the confirmation driving pattern.
(f) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
(g) Read DTCs.
Result
Result
Proceed to
No DTC is output
A
P0340, P0342, P0343, P0345, P0347 or P0348 is output