This monitor will run when the engine is started at an engine coolant temperature of -10 to 50 °C. The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).
The DTC is designed to monitor the ignition timing at cold start. When the engine is started at an engine coolant temperature of lower than 50 °C, the ECM checks the ignition timing at engine idling. If the ignition timing advances beyond the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is stored when the malfunction is detected in consecutive driving cycles (2 trip detection logic).
NOTICE:
When the cable is disconnected from the negative battery terminal during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be stored with the ISC learning values cleared.
HINT:
The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.
Accumulated time when ignition timing retard is cut off
8 seconds or more
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
Check that "Coolant Temp" in the Data List is within the range of -10 to 50 °C.
Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.
Idle the engine for 1 minute or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTC.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P050B.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [B].
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
HINT:
DTC P050B may be set when the engine has the symptoms listed below. If necessary, check the trouble areas listed below.
Symptom
Factor
Trouble Area
Low idle speed when engine is cold (immediately after engine start)
Excessive engine friction
Engine oil deterioration
Drive belt tension
A/C compressor
Generator
Vane pump
Rough idle when engine is cold (immediately after engine start)
Abnormal combustion
Fuel quality
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the pending DTCs.
Result
Result
Proceed to
DTC P050B is output
A
DTC P050B and other DTCs are output
B
HINT:
If any DTCs other than P050B are output, troubleshoot those DTCs first.
B
GO TO DTC CHART
A
READ VALUE USING TECHSTREAM (FUEL TRIM)
HINT:
Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Data List / Short FT B1S1 and Long FT B1S1, or Short FT B2S1 and Long FT B2S1.
(e) Read the values displayed on the Techstream.
(f) Add together the Short FT B1S1 and Long FT B1S1, or Short FT B2S1 and Long FT B2S1 values to obtain the total fuel trim.
OK:
Total of Short FT B1S1 and Long FT B1S1, or Short FT B2S1 and Long FT B2S1 values is between -20% and 20%.
NG
GO TO STEP 7
OK
INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE BODY)
(a) Check for deposits around the throttle valve and check the throttle valve condition.
OK:
No deposits around throttle valve and throttle valve moves smoothly.
NG
GO TO STEP 6
OK
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 75 °C or higher.
HINT:
When performing the Active Test, make sure the shift lever is in P or N.
The A/C switch and all accessory switches should be off.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
(e) Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
HINT:
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
OK:
MAP and idling condition change in response to EGR step position as follows.
Standard:
-
EGR Step Position (Active Test)
0 Steps
0 to 30 Steps
Idling condition
Steady idling
Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg)
MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed
OK
GO TO STEP 19
NG
INSPECT EGR VALVE ASSEMBLY
(a) Remove the EGR valve (See page ).
(b) Check if the EGR valve is stuck open.
OK:
EGR valve is tightly closed.
OK
GO TO STEP 19
NG
GO TO STEP 17
REPAIR OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
(a) Repair or replace the throttle with motor body assembly (See page ).
HINT:
Perform "Inspection After Repair" after repairing or replacing the throttle with motor body assembly (See page ).
NEXT
GO TO STEP 19
CHECK PCV HOSE
(a) Check the PCV hose connections (See page ).
OK:
PCV hose is connected correctly and is not damaged.
NG
GO TO STEP 14
OK
CHECK INTAKE SYSTEM
(a) Check the intake system for vacuum leaks (See page ).
OK:
No leak in the intake system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system (See page ).
NG
GO TO STEP 15
OK
INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
(a) Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.
OK:
The air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.
NG
GO TO STEP 16
OK
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 75 °C or higher.
HINT:
When performing the Active Test, make sure the shift lever is in P or N.
The A/C switch and all accessory switches should be off.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
(e) Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
HINT:
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
OK:
MAP and idling condition change in response to EGR step position as follows.
Standard:
-
EGR Step Position (Active Test)
0 Steps
0 to 30 Steps
Idling condition
Steady idling
Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg)
MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed
OK
GO TO STEP 12
NG
INSPECT EGR VALVE ASSEMBLY
(a) Remove the EGR valve assembly (See page ).
(b) Check if the EGR valve is stuck open.
OK:
EGR valve is tightly closed.
NG
GO TO STEP 17
OK
PERFORM ACTIVE TEST USING TECHSTREAM
(a) Operate the VVT system through the Active test, and check if the VVT system is operating normally.
(1) Perform the Active Test, referring to DTC P0011 inspection procedure (VVT system for intake side) (See page ).
(2) Perform the Active Test, referring to DTC P0014 inspection procedure (VVT system for exhaust side) (See page ).
NG
GO TO STEP 18
OK
READ VALUE USING TECHSTREAM (MAF)
(a) Connect the Techstream to the DLC3.
(b) Start the engine and turn the Techstream on.
(c) Enter the following menus: Powertrain / Engine and ECT / Data List / MAF and Coolant Temp.
(d) Allow the engine to idle until Coolant Temp reaches 75 °C or higher.
(e) Read MAF with the engine speed at 3000 rpm.
Standard:
Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off)
OK
GO TO STEP 19
NG
GO TO STEP 20
REPAIR OR REPLACE PCV HOSE
(a) Repair or replace the PCV hose.
NEXT
GO TO STEP 19
REPAIR OR REPLACE INTAKE SYSTEM
(a) Repair or replace the intake system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system (See page ).
NEXT
GO TO STEP 19
REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
(a) Replace the air cleaner filter element sub-assembly.
NEXT
GO TO STEP 19
REPLACE EGR VALVE ASSEMBLY
(a) Replace the EGR valve assembly (See page ).
HINT:
Perform "Inspection After Repair" after repairing or replacing the EGR valve assembly (See page ).
NEXT
GO TO STEP 19
CHECK AND REPAIR VVT SYSTEM
(a) Check and repair the VVT system.
HINT:
Refer to DTC P0011 Inspection Procedure (VVT system for intake side) (See page ).
Refer to DTC P0014 Inspection Procedure (VVT system for exhaust side) (See page ).
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
NOTICE:
In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs (See page ).
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON and turn the Techstream on.
(g) Start the engine and warm it up.
(h) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
(j) Input the DTC: P050B.
(k) Check the DTC judgment result.
Result
Result
Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P050B is output)
B
A
CHECK FOR INTERMITTENT PROBLEMS
B
CHECK HARNESS AND CONNECTOR
(a) Check the connection and terminal and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page ).
HINT:
Repair any problems.
NEXT
CHECK WHETHER DTC OUTPUT RECURS
NOTICE:
In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs (See page ).
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON and turn the Techstream on.
(g) Start the engine and warm it up.
(h) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
(j) Input the DTC: P050B.
(k) Check the DTC judgment result.
Result
Result
Proceed to
ABNORMAL
(DTC P050B is output)
A
NORMAL
(DTC is not output)
B
B
END
A
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
(a) Disconnect the MAF meter connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D7-3 (VG) - D74-74 (VG)
Always
Below 1 Ω
D7-2 (E2G) - D74-75 (E2G)
Always
Below 1 Ω
D7-3 (VG) or D74-74 (VG) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MASS AIR FLOW METER
(a) Replace the mass air flow meter (See page ).
HINT:
If the result of the inspection performed in step 13 indicated no problem, proceed to the next step without replacing the mass air flow meter.
Perform "Inspection After Repair" after replacing the mass air flow meter (See page ).
NEXT
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
NOTICE:
In this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs (See page ).
(e) Turn the ignition switch off and wait for at least 30 seconds.
(f) Turn the ignition switch to ON and turn the Techstream on.
(g) Start the engine and warm it up.
(h) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
(i) Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.