Crankshaft Position Sensor "A" Circuit (P0335,P0337-P0339)
In this manual: Engine, Hybrid System
13steps
~78min
3/5difficulty
Done 0 of 13
DESCRIPTION
The crankshaft position (CKP) sensor system consists of a crankshaft angle sensor plate and Magnetoresistive Element (MRE) type sensor. The crankshaft angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed to the rear end of the crankshaft. The crankshaft position sensor outputs 34 rotation signals per crankshaft revolution. The ECM uses the G2 signal to distinguish between the cylinders, and uses the NE signal to detect the crankshaft position and engine rpm.
DTC No.
DTC Detection Condition
Trouble Area
P0335
Either condition is met:
No crankshaft position (CKP) sensor signal to ECM while cranking (1 trip detection logic)
No crankshaft position (CKP) sensor signal to ECM at engine speed of 450 rpm or more (1 trip detection logic)
Open or short in crankshaft position (CKP) sensor circuit
Crankshaft position (CKP) sensor
Crankshaft position (CKP) sensor plate
ECM
P0337
Output voltage of CKP sensor 0.3 V or less for 4 seconds (1 trip detection logic)
Open or short in CKP sensor circuit
CKP sensor
CKP sensor plate
ECM
P0338
Output voltage of CKP sensor 4.7 V or more for 4 seconds (1 trip detection logic)
Open or short in CKP sensor circuit
CKP sensor
CKP sensor plate
ECM
P0339
Under conditions (a), (b) and (c), no CKP sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or more
(b) Starter signal OFF
(c) 3 seconds or more have elapsed since starter signal switched from ON to OFF
Open or short in CKP sensor circuit
CKP sensor
CKP sensor plate
ECM
Reference: Inspection using an oscilloscope.
Standard:
Tester Connection
Tool Setting
Condition
Specified Condition
D74-110 (NE+) - D74-111 (NE-)
5 V/DIV., 20 msec./DIV.
Cranking or idling
The correct waveform is as shown
D74-90 (G2) - D74-89 (G2-)
5 V/DIV., 20 msec./DIV.
Cranking or idling
The correct waveform is as shown
HINT:
G2 is the camshaft position sensor signal, and NE is the crankshaft position sensor signal.
MONITOR DESCRIPTION
If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.
When the sensor output voltage remains at less than 0.3 V, or more than 4.7 V for more than 4 seconds, the ECM stores a DTC.
MONITOR STRATEGY
Related DTCs
P0335: Crankshaft position sensor range check/rationality
P0337: Crankshaft position sensor check (Low voltage)
P0338: Crankshaft position sensor check (High voltage)
Required sensors/Components (Main)
Crankshaft Position (CKP) sensor
Required sensors/Components (Related)
Camshaft position sensor
Frequency of operation
Continuous
Duration
P0335: 4.7 seconds
P0337, P0338: 4 seconds
MIL operation
Immediate
Sequence of operation
None
TYPICAL ENABLING CONDITIONS
ALL
Monitor runs whenever following DTCs not present
None
P0335: Crankshaft Position Sensor Range Check Case 1
Engine speed (Top dead center)
450 rpm or more
Engine speed (30°CA)
450 rpm or more
Starter
OFF
Time after starter turned from ON to OFF
3 seconds or more
CKP sensor voltage
0.3 to 4.7 V
Case 2
Starter
ON
Minimum battery voltage while starter ON
Below 11 V
CKP sensor voltage
0.3 to 4.7 V
P0337, P0338 Crankshaft Position Sensor Range Check (Low Voltage, High Voltage)
Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF
TYPICAL MALFUNCTION THRESHOLDS
P0335 Crankshaft Position Sensor Range Check
Engine speed signal
No signal
P0337 Crankshaft Position Sensor Range Check (Low Voltage)
CKP sensor voltage
Less than 0.3 V
P0338 Crankshaft Position Sensor Range Check (High Voltage)
CKP sensor voltage
More than 4.7 V
COMPONENT OPERATING RANGE
CKP sensor
CKP sensor output voltage fluctuates while engine crankshaft revolving
34 CKP sensor signals per crankshaft revolution
CKP sensor voltage
0.3 to 4.7 V
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 20 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0335, P0337 or P0338.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
HINT:
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
The engine speed can be checked by using the Techstream. To perform the check, follow the procedures below:
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position (CKP) sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the CKP sensor output voltage is insufficient.
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
READ VALUE USING TECHSTREAM (ENGINE SPEED)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
(e) Start the engine.
(f) Read the values displayed on the Techstream while the engine is running.
Standard:
Correct values are displayed.
HINT:
To check the engine speed change, display the graph on the Techstream.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the Techstream remains zero (0), there may be an open or short in the Crankshaft Position (CKP) sensor circuit.
OK
CHECK FOR INTERMITTENT PROBLEMS
NG
INSPECT CRANKSHAFT POSITION SENSOR (SENSOR POWER SOURCE)
(a) Disconnect the crankshaft position sensor connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D3-3 (VC) - Body ground
Ignition switch ON
4.5 to 5.0 V
NG
GO TO STEP 8
OK
CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
(a) Disconnect the crankshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D3-1 (NE+) - D74-110 (NE+)
Always
Below 1 Ω
D3-2 (NE-) - D74-111 (NE-)
Always
Below 1 Ω
D3-1 (NE+) or D74-110 (NE+) - Body ground
Always
10 kΩ or higher
D3-2 (NE-) or D74-111 (NE-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
(a) Check the crankshaft position sensor installation.
OK:
Sensor is installed correctly.
NG
SECURELY REINSTALL SENSOR
OK
INSPECT CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
(a) Check the teeth of the sensor plate.
OK:
Sensor plate does not have any cracks or deformation.
NG
REPLACE CRANKSHAFT POSITION SENSOR PLATE
OK
REPLACE CRANKSHAFT POSITION SENSOR
(a) Replace the crankshaft position sensor (See page ).