Throttle Actuator Control Motor Circuit Low (P2102,P2103)
In this manual: Engine, Hybrid System
14steps
~84min
4/5difficulty
Done 0 of 14
DESCRIPTION
The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the Throttle Position (TP) sensor, which is mounted on the throttle with motor body assembly. The TP sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.
HINT:
This ETCS (Electronic Throttle Control System) does not use a throttle cable.
DTC No.
DTC Detection Condition
Trouble Area
P2102
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) Throttle actuator duty ratio 80% or more
(b) Throttle actuator current less than 0.5 A
Open in throttle actuator circuit
Throttle actuator
ECM
P2103
Either of following conditions met (1 trip detection logic):
Motor driver IC diagnosis signal failure
Motor driver IC current limiter port failure
Short in throttle actuator circuit
Throttle actuator
Throttle valve
Throttle with motor body assembly
ECM
MONITOR DESCRIPTION
The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.
Example:
When the electrical current is less than 0.5 A and the throttle actuator duty ratio exceeds 80%, the ECM interprets this as the current being outside the standard range, and illuminates the MIL and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored when the engine is quickly revved to a high rpm several times after the engine is started and has idled for 5 seconds.
MONITOR STRATEGY
Related DTCs
P2102: Throttle actuator current (low current)
P2103: Throttle actuator current (high current)
Required Sensors/Components (Main)
Throttle actuator (throttle body)
Required Sensors/Components (Related)
None
Frequency of Operation
Continuous
Duration
2 seconds: P2102
25 times: P2103 (Case 1)
0.6 seconds: P2103 (Case 2)
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
P2102
Throttle actuator
ON
Duty-cycle to throttle actuator
80% or more
Throttle actuator power supply
8 V or more
P2103
Battery voltage
8 V or more
Starter
OFF
Electronic throttle actuator
ON
Either of the following conditions 1 or 2 met:
-
1. Electronic throttle actuator power supply voltage
8 V or more
2. Electronic throttle actuator power
ON
TYPICAL MALFUNCTION THRESHOLDS
P2102
Motor current
Less than 0.5 A
P2103 (Case 1)
Motor driver IC high current inhibit signal
ON
P2103 (Case 2)
Motor driver IC high current limiter monitor input
Fail
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine.
With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].
Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2102 or P2103.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
FAIL-SAFE
When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 7° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal opening angle to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.
WIRING DIAGRAM
HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Open Duty/Throttle Motor Close Duty) can be read using the Techstream. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.
PROCEDURE
INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
(a) Disconnect the throttle with motor body assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20 °C
0.3 to 100 Ω
HINT:
Perform "Inspection After Repair" after replacing the throttle with motor body assembly (See page ).
NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
OK
CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
(a) Disconnect the throttle body connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D9-2 (M+) - D74-19 (M+)
Always
Below 1 Ω
D9-1 (M-) - D74-18 (M-)
Always
Below 1 Ω
D9-2 (M+) or D74-19 (M+) - Body ground
Always
10 kΩ or higher
D9-1 (M-) or D74-18 (M-) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
(a) Check for foreign objects between the throttle valve and the housing.
OK:
No foreign objects between throttle valve and housing.
HINT:
Perform "Inspection After Repair" after cleaning the throttle with motor body assembly (See page ).
NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY
OK
INSPECT THROTTLE VALVE
(a) Check if the throttle valve opens and closes smoothly.
OK:
Throttle valve opens and closes smoothly.
HINT:
Perform "Inspection After Repair" after replacing the throttle with motor body assembly (See page ).