P2431, P2432, P2433, P2436, P2437, P2438 (Secondary Air Injection System Pressure Sensor)
P2440 (Case 1), P2441, P2442 (Case 1), P2443
Battery voltage
11 V or more
Atmospheric pressure
45 kPa (338 mmHg) or more
Engine
Running
AIR monitor during AIR: ON*1
Completed
AIR monitor during AIR: OFF*2
Completed
AIR injection driver fail (open/short or out of range)
Not detected
AIR pressure sensor fail (open/short or out of range)
Not detected
*1: AIR monitor during AIR: ON
-
Time after AIR in operation
5 seconds or more
AIR pump
ON
AIR valve
Open
Engine speed
400 to 3750 rpm
Intake air amount
Less than 100 gm/s
Time after engine start
1 second or more
*2: AIR monitor during AIR: OFF
-
Time after AIR in operation
10 seconds or more
AIR pump
OFF
AIR valve
Close
Engine speed
Below 3000 rpm
AIR monitor during AIR: ON
Completed
Time after engine start
1 second or more
P2440, P2442 AIR valve is stuck open (Case 2)
One of the following conditions is met
(a), (b) or (c)
(a) Cumulative intake air amount
100 gm/s or more
(b) Difference between starting temperature and current temperature
10 °C or higher
(c) Starting coolant temperature
60 °C or higher
AIR pump
OFF
AIR valve
Close
Engine speed
3750 rpm or less
AIR pressure sensor fail (open/short or out of range)
Not detected
Time after engine started
1 second or more
Time after AIR in operation
10 seconds or more
AIR valve open stuck
Not detected
AIR pressure sensor open stuck (DTC P2445, P2447)
Not in operation
Engine load
20% or more
TYPICAL MALFUNCTION THRESHOLDS
Secondary Air Injection ON (Condition 1)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
18 kPa or higher
AIR pressure
1.9 kPa or higher
Secondary Air Injection ON (Condition 2)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
18 kPa or higher
AIR pressure
Below 1.9 kPa
Secondary Air Injection ON (Condition 3)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 18 kPa
AIR pressure
1.9 kPa or higher
Secondary Air Injection ON (Condition 4)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 18 kPa
AIR pressure
Below 1.9 kPa
Secondary Air Injection OFF (Condition 1)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
25 kPa or higher
AIR pressure
3 kPa or higher
Secondary Air Injection OFF (Condition 2)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
25 kPa or higher
AIR pressure
Below 3 kPa
Secondary Air Injection OFF (Condition 3)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 25 kPa
AIR pressure
3 kPa or higher
Secondary Air Injection OFF (Condition 4)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 25 kPa
AIR pressure
Below 3 kPa
P2440, P2442 AIR valve is stuck open (Case 1)
Either condition is met
(a) or (b)
(a) AIR OFF Condition 1
Met
(b) AIR OFF Condition 2
Met
P2441, P2443 AIR valve is stuck closed
Either condition is met
(a) or (b)
(a) AIR ON Condition 3
Met
(b) AIR ON Condition 4
Met
P2440, P2442 AIR valve is stuck open (Case 2)
Cumulative pressure pulsation
75 kPa or higher
MONITOR RESULT
Refer to Checking Monitor Status (See page ).
CONFIRMATION DRIVING PATTERN
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (if set) (See page ).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).
Check for pending DTCs.
OK:
No pending DTC is output.
After the "Secondary air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2440, P2441, P2442 or P2443.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If no permanent DTC is output, the system is normal.
If a permanent DTC is output, the system is malfunctioning.
Turn the ignition switch off.
WIRING DIAGRAM
Refer to DTC P0412 (See page ).
HINT:
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are AIR system pressure conditions in the AIR system passage.
Pressure Condition in Secondary Air Injection System Case 1
Air Pump
ON
Air Switching Valve
Open
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 2
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 3
Air Pump
ON
Air Switching Valve
Closed
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected
Pressure Condition in Secondary Air Injection System Case 4
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation not detected
Pressure Condition in Secondary Air Injection System Case 5
Air Pump
ON
Air Switching Valve
Open
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 6
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 7
Air Pump
ON
Air Switching Valve
Closed
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected
Pressure Condition in Secondary Air Injection System Case 8
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.
HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
HINT:
In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 18 to 25 kPa).
In case 1, the average pressure is approximately 3 to 11 kPa. The value of 1.9 kPa indicated in the table above is a threshold for detecting pump malfunctions.
Detected Condition while AIR Operating:
Air Pump ON, ASV Open
Detected Condition while AIR not Operating:
Air Pump OFF, ASV Closed
ECM Determination
DTC Output
Case 1
Case 8
Normal
-
Case 1
Case 6
Air switching valve stuck open
P2440
or
P2442
Case 1
Case 7
Air pump stuck ON
P2444
or
P2446
Case 2
Case 8
Air pump stuck OFF
P2445
or
P2447
Case 3
Case 8
Air switching valve stuck closed
P2441
or
P2443
Case 1
Case 5
Air switching valve stuck open and air pump stuck ON
P2440 and P2444
or
P2442 and P2446
Case 2
Case 6
Air switching valve stuck open and air pump stuck OFF
P2440 and P2445
or
P2442 and P2447
Case 3
Case 7
Air switching valve stuck closed and air pump stuck ON
P2441 and P2444
or
P2443 and P2446
Case 4
Case 8
Air switching valve stuck closed and air pump stuck OFF
P2441 and P2445
or
P2443 and P2447
HINT:
By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
System Check:
The pressure in the secondary air passage can be checked using the Techstream.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.
Standard:
Tester Operation
Air Pump
ASV
Pressure*1
Pulsation*2
AIR PUMP: ON, ASV: OPEN
ON
OPEN
1.9 kPa or more
18 kPa or more
AIR PUMP: OFF, ASV: CLOSE
OFF
CLOSE
Less than 3.0 kPa
Less than 25 kPa
*1: Average pumping pressure (gauge pressure). The pressure should be 1.9 kPa or more when the AIR system operates.
*2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
Turn the ignition switch off.
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read DTCs.
Result
Result
Proceed to
P2440, P2441, P2442 and/or P2443 is output
A
P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output
B
P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output
C
If any DTCs other than P0412, P0415, P2440, P2441, P2442 and/or P2443 are output, troubleshoot those DTCs first.
B
GO TO AIR SWITCHING VALVE ASSEMBLY INSPECTION PROCEDURE (P0412 AND P0415)
C
GO TO DTC CHART
A
PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMP HEATER)
(a) Disconnect the air pump assembly (for bank 1 or Bank 2) connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON and turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Condition
Specified Condition
D89-1 (APH+) - Body ground
Activate the Air Pump Heater is ON
11 to 14 V
D90-1 (APH+) - Body ground
Activate the Air Pump Heater is ON
11 to 14 V
(f) Reconnect the air pump assembly (for bank 1 or Bank 2) connector.
NG
GO TO STEP 4
OK
INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2) (HEATER RESISTANCE)
(a) Inspect the air pump assembly (for bank 1 or bank 2) (See page ).
NG
REPLACE AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
OK
INSPECT AIR PUMP HEATER (AI HTR) RELAY
NG
REPLACE AIR PUMP HEATER (AI-HTR) RELAY
OK
CHECK AIR PUMP HEATER (AI HTR) RELAY (POWER SOURCE)
(a) Remove the air pump heater (AI HTR) relay.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Condition
Specified Condition
AI HTR relay terminal 5 - Body ground
Always
11 to 14 V
(c) Reinstall the air pump heater (AI-HTR) relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (AIR PUMP ASSEMBLY - AI HTR RELAY, BODYGROUND)
(a) Remove the air pump heater (AI HTR) relay.
(b) Disconnect the air pump assembly (for bank 1 or bank 2) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
AI HTR relay terminal 3 - D89-1 (APH+)
Always
Below 1 Ω
AI HTR relay terminal 3 - D90-1 (APH+)
Always
Below 1 Ω
D89-3 (APHG) - Body ground
Always
Below 1 Ω
D90-3 (APHG) - Body ground
Always
Below 1 Ω
AI HTR relay terminal 3 or D89-1 (APH+) - Body ground
Always
10 kΩ or higher
AI HTR relay terminal 3 or D90-1 (APH+) - Body ground
Always
10 kΩ or higher
(d) Reinstall the air pump heater (AI HTR) relay.
(e) Reconnect the air pump assembly (for bank 1 or bank 2) connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
(a) Inspect the air pump assembly (for bank 1 or bank 2) (See page ).
NG
REPLACE AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
OK
PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
(a) Visual check:
(1) Start the engine and warm it up.
(2) Turn the ignition switch off.
(3) Disconnect the No. 1 air hose.
(4) Connect the Techstream to the DLC3.
(5) Turn the ignition switch to ON.
(6) Turn the Techstream on.
(7) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AP and ASV operation can be selected.
(8) Start the engine.
(9) Perform the AIR system forced operation while the engine is idling.
(10) Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.
CAUTION:
To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.
(11) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.
(12) Check that the exhaust gas does not pulsate when the ASV is turned OFF.
(13) Turn the ignition switch off.
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK:
Air Pump Operation
ASV Operation
Exhaust Gas Pulsation
ON
OFF
Not detected
ON
ON
Detected
(b) Other inspection method:
The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.
Perform System Check operation under Manual Mode.
*: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
(1) Start the engine and warm it up.
(2) Turn the ignition switch off.
(3) Connect the Techstream to the DLC3.
(4) Turn the ignition switch to ON.
(5) Turn the Techstream on.
(6) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
(7) Start the engine after the Techstream initialization is finished.
(8) Perform the AIR system forced operation while the engine is idling.
(9) Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream indicate the conditions shown in the table below.
(10) Turn the ignition switch off.
OK:
AIR System Operation
Pulsation Condition
(ECM Calculation)
Air-Fuel Ratio
(Reference)
AIR PUMP: ON, ASV: OPEN
18 kPa or more
18 or more
AIR PUMP: OFF, ASV: CLOSE
Less than 25 kPa
Approximately 14.5
(around stoichiometric air-fuel ratio)
Reference:
If the air pump operation is confirmed as normal (See page ), the air-fuel ratio detected in front of the three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.
Result
Result
Proceed to
NG
A
OK
B
B
GO TO STEP 16
A
INSPECT AIR TUBE (BLOCKAGE AND LEAK)
(a) Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the air switching valve assembly.
(b) Inspect the air tube for blockages and damage.
OK:
No blockages in or damage to air tubes.
NG
REPLACE AIR TUBE
OK
INSPECT AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1 OR BANK 2)
(a) Inspect the air switching valve (for bank 1) (See page ).
(b) Inspect the air switching valve (for bank 2) (See page ).
Result
Result
Proceed to
OK
A
NG (for Bank 1)
B
NG (for Bank 2)
C
B
REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1)
C
REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 2)
A
INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
(a) Disconnect the air injection control driver (AID) (for bank 1 or bank 2) connectors.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D48-1 (BATT) - Body ground
Always
11 to 14 V (near battery voltage)
D50-5 (+B) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
D52-1 (BAT2) - Body ground
Always
11 to 14 V (near battery voltage)
D54-5 (+B2) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D50-1 (E) - Body ground
Always
Below 1 Ω
D54-1 (E2) - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK
CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
(a) Disconnect the ECM connectors.
(b) Disconnect the air injection control driver (AID) (for bank 1 or bank 2) connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D74-28 (AIRV) - D50-3 (SIV)
Always
Below 1 Ω
A24-43 (ARV2) - D54-3 (SIV2)
Always
Below 1 Ω
D74-28 (AIRV) or D50-3 (SIV) - Body ground
Always
10 kΩ or higher
A24-43 (ARV2) or D54-3 (SIV2) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
PERFORM ACTIVE TEST USING TECHSTREAM
(a) Disconnect the air injection control driver (AID) (for bank 1 or bank 2) connector.
(b) Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON and turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(f) Start the engine.
(g) Perform the AIR system forced operation while the engine is idling.
(h) Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
(i) Turn the ignition switch off.
NOTICE:
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Standard Voltage:
Tester Connection
Condition
Specified Condition
D50-3 (SIV) - D50-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D54-3 (SIV2) - D54-1 (E2)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D50-3 (SIV) - D50-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
D54-3 (SIV2) - D54-1 (E2)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
(j) Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
(k) Connect the Techstream to the DLC3.
(l) Turn the ignition switch to ON and turn the Techstream on.
(m) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(n) Start the engine.
(o) Perform the AIR system forced operation while the engine is idling.
(p) Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
(q) Turn the ignition switch off.
NOTICE:
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Standard Voltage:
Tester Connection
Condition
Specified Condition
D50-4 (SIP) - D50-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D54-4 (SIP2) - D54-1 (E2)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D50-4 (SIP) - D50-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
D54-4 (SIP2) - D54-1 (E2)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
NG
REPLACE ECM
OK
REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)
(a) Replace the air injection control driver (for bank 1 or bank 2) (See page ).
(g) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
(h) Start the engine after the Techstream initialization is finished.
(i) Perform the System Check operation by pressing ENTER (Next).
(j) After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
(k) Check pending DTCs.
(l) Turn the ignition switch off.
OK:
No pending DTC output.
NOTICE:
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.