Secondary Air Injection System Driver (P1613,P1614)
In this manual: Engine, Hybrid System
21steps
~126min
5/5difficulty
Done 0 of 21
DESCRIPTION
Refer to DTC P0412 (See page ).
DTC No.
DTC Detection Condition
Trouble Area
P1613
P1614
Either of following conditions (1) or (2) met:
(1) All of following conditions met (1 trip detection logic):
Either air pump or air switching valve not operating
Diagnostic signal from Air Injection Control Driver (AID) 80%
Battery voltage 8 V or more
(2) Both of following conditions met (1 trip detection logic):
Battery voltage 8 V or more
Diagnostic signal from AID abnormal (duty signal other than 0, 20, 40, 80 and 100%)
Air injection control driver
Open in air injection control driver ground circuit
P1613
P1614
All of following conditions met (1 trip detection logic):
Air injection system operating (Air Switching Valve [ASV] ON and air pump ON)
Diagnostic signal from Air Injection Control Driver (AID) 0%
Battery voltage 8 V or more
Short in diagnostic information signal circuit (Air injection control driver - ECM)
Open or short in air pump and air switching valve command signal circuit (Air injection control driver - ECM)
Open in air injection control driver ground circuit
Air injection control driver
ECM
P1613
P1614
Both of following conditions met (1 trip detection logic):
Battery voltage 8 V or more
Diagnostic signal from Air Injection Control Driver (AID) 100%
Open or short in air injection control driver +B circuit
Open in diagnostic information signal circuit (Air injection control driver - ECM)
Air injection control driver
ECM
MONITOR DESCRIPTION
For a short time after a cold engine start, the ECM transmits command signals to the Air Injection Control Driver (AID) to drive the air pump and the Air Switching Valve (ASV). The AID detects open and short circuits according to the voltages at the AID terminals connected to the air pump and ASV, and the circuit voltage of the AID power source, and transmits diagnostic information as a signal to the ECM.
If the Secondary Air Injection (AIR) system circuit or the AID itself malfunctions, the AID sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM stores the DTC based on the diagnostic information from the AID.
EXAMPLE:
The duty ratio of the diagnostic signal from the AID is 0 or 100% (remains at 0 V or the same as battery voltage).
The duty ratio of the diagnostic signal from the AID shows an impossible ratio (other than 0, 20, 40, 80 and 100%).
The AID outputs the normal signal (normal duty signal: 80%) while the system is not operating.
MONITOR STRATEGY
Related DTCs
P1613: Secondary air injection system air injection control driver circuit range check
P1614: Secondary air injection system air injection control driver circuit range check
Required Sensors/Components (Main)
Air injection control driver
Required Sensors/Components (Related)
Air switching valve
Frequency of Operation
Once per drive cycle
Duration
3 seconds
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
Case 1 and 4
Monitor runs whenever following DTCs not present
None
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
Case 2
Monitor runs whenever following DTCs not present
None
Either a or b met:
-
a. Air pump
Not operating
b. Air switching valve
Not operating
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
Case 3
Monitor runs whenever following DTCs not present
None
Following conditions (a) and (b) met
-
a. Air pump
Operating
b. Air switching valve
Operating
Battery voltage
8 V or more
Ignition switch
ON
Starter
OFF
TYPICAL MALFUNCTION THRESHOLDS
Case 1
One of following conditions met:
A, B, C or D
A. Diagnostic signal duty ratio from air injection control driver
1% or more, and 10% or less
B. Diagnostic signal duty ratio from air injection control driver
30%
C. Diagnostic signal duty ratio from air injection control driver
49%
D. Diagnostic signal duty ratio from air injection control driver
91% or more, and 99% or less
Case 2
Diagnostic signal duty ratio from air injection control driver
70% or more, and 90% or less
Case 3
Diagnostic signal duty ratio from air injection control driver
0%
Case 4
Diagnostic signal duty ratio from air injection control driver
100%
COMPONENT OPERATING RANGE
Diagnostic signal duty ratio from air injection control driver
70% or more, and 90% or less when secondary air injection system operating.
0% when secondary air injection system not operating.
CONFIRMATION DRIVING PATTERN
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (if set) (See page ).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).
Check for pending DTCs.
OK:
No pending DTC is output.
After the "Secondary air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P1613 or P1614.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If no permanent DTC is output, the system is normal.
If a permanent DTC is output, the system is malfunctioning.
Turn the ignition switch off.
WIRING DIAGRAM
Refer to DTC P0412 (See page ).
HINT:
By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613 OR P1614)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read DTCs.
Result
Result
Proceed to
P1613 and/or P1614 is output
A
P1613 and/or P1614 and other DTCs are output
B
If any DTCs other than P1613 and P1614 are output, troubleshoot those DTCs first.
B
GO TO DTC CHART
A
CHECK AIR INJECTION CONTROL DRIVER (POWER SOURCE CIRCUIT)
(a) Disconnect the air injection control driver (AID) connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D50-5 (+B) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
D54-5 (+B2) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (AID - ECM, BODY GROUND)
(a) Disconnect the ECM connector.
(b) Disconnect the AID connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D74-54 (AIRP) - D50-4 (SIP)
Always
Below 1 Ω
D74-28 (AIRV) - D50-3 (SIV)
Always
Below 1 Ω
D74-53 (ARP2) - D54-4 (SIP2)
Always
Below 1 Ω
A24-43 (ARV2) - D54-3 (SIV2)
Always
Below 1 Ω
D74-30 (AIDI) - D50-2 (DI)
Always
Below 1 Ω
D74-29 (AID2) - D54-2 (DI2)
Always
Below 1 Ω
D50-1 (E) - Body ground
Always
Below 1 Ω
D54-1 (E2) - Body ground
Always
Below 1 Ω
D74-54 (AIRP) or D50-4 (SIP) - Body ground
Always
10 kΩ or higher
D74-28 (AIRV) or D50-3 (SIV) - Body ground
Always
10 kΩ or higher
D74-53 (ARP2) or D54-4 (SIP2) - Body ground
Always
10 kΩ or higher
A24-43 (ARV2) or D54-3 (SIV2) - Body ground
Always
10 kΩ or higher
D74-30 (AIDI) or D50-2 (DI) - Body ground
Always
10 kΩ or higher
D74-29 (AID2) or D54-2 (DI2) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
(a) Disconnect the AID connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D50-2 (DI) - D50-1 (E)
Ignition switch ON
11 to 14 V (near battery voltage)
D54-2 (DI2) - D54-1 (E2)
Ignition switch ON
11 to 14 V (near battery voltage)
NG
REPLACE ECM
OK
PERFORM ACTIVE TEST USING TECHSTREAM
(a) Disconnect the AID connector.
(b) Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON and turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(f) Start the engine.
(g) Perform the AIR system forced operation while the engine is idling.
(h) Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
(i) Turn the ignition switch off.
NOTICE:
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Standard Voltage:
Tester Connection
Condition
Specified Condition
D50-3 (SIV) - D50-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D54-3 (SIV2) - D54-1 (E2)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D50-3 (SIV) - D50-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
D54-3 (SIV2) - D54-1 (E2)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
(j) Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
(k) Connect the Techstream to the DLC3.
(l) Turn the ignition switch to ON and turn the Techstream on.
(m) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(n) Start the engine.
(o) Perform the AIR system forced operation while the engine is idling.
(p) Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
(q) Turn the ignition switch off.
NOTICE:
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Standard Voltage:
Tester Connection
Condition
Specified Condition
D50-4 (SIP) - D50-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D54-4 (SIP2) - D54-1 (E2)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D50-4 (SIP) - D50-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
D54-4 (SIP2) - D54-1 (E2)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
NG
REPLACE ECM
OK
REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)
(a) Replace the air injection control driver (for bank 1 or bank 2) (See page ).
NEXT
CHECK WHETHER DTC OUTPUT RECURS
(a) Start the engine and warm it up.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Clear DTCs (See page ).
(g) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
(h) Start the engine after the Techstream initialization is finished.
(i) Perform the System Check operation by pressing ENTER (Next).
(j) After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
(k) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
(l) Read DTCs.
Result
Result
Proceed to
No DTC is output
A
Other DTCs are output
B
(m) Turn the ignition switch off.
NOTICE:
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.