While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h or more for over 20 seconds.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) met, positive (+B) battery voltage of 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
(a) Vehicle speed 20 km/h or more
(b) Engine speed 1000 rpm or more
(c) STA signal ON
Park/Neutral Position (PNP) switch
Starter relay circuit
Ignition switch assembly
ECM
MONITOR STRATEGY
Related DTCs
P0617: Starter signal
Required Sensors/Components (Main)
ST relay, PNP switch and ignition switch
Required Sensors/Components (Related)
Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor
Frequency of Operation
Continuous
Duration
20 seconds
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or more
Vehicle speed
20 km/h or more
Engine speed
1000 rpm or more
TYPICAL MALFUNCTION THRESHOLDS
Starter signal
ON
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Idle the engine for 5 seconds or more [B].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0617.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].
Drive the vehicle at 24 km/h or more for 20 seconds or more [D].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Check the DTC judgment result [E].
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
HINT:
The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.
If the engine will not crank, proceed to the Problem Symptoms Table (See page ).
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
READ VALUE USING TECHSTREAM (STARTER SIGNAL)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
(e) Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
OK
CHECK FOR INTERMITTENT PROBLEMS
NG
READ VALUE USING TECHSTREAM (STARTER SIGNAL)
(a) Disconnect the Park/Neutral Position (PNP) switch connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
(f) Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
Result
Starter Signal
Proceed to
Remains ON
A
OFF
B
B
GO TO STEP 4
A
INSPECT ECM (STA TERMINAL VOLTAGE)
(a) Disconnect the ECM connector.
(b) Disconnect the PNP switch connector.
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Condition
Specified Condition
Proceed to
A24-46 (STA) - Body ground
Ignition switch ON
Below 1.5 V
A
11 to 14 V
B
A
REPLACE ECM
B
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PNP SWITCH - ST RELAY)
INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Disconnect the PNP switch connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
4 (B) - 5 (L)
Except P or N
10 kΩ or higher
2 (RB) - 5 (L)
All positions
10 kΩ or higher
Result
Result
Proceed to
Short between 4 and 5
A
Short between 2 and 5
B
Within standard range
C
B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
C
GO TO STEP 6
A
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
(a) Replace the park/neutral position switch.
for 2WD (See page )
for 4WD (See page )
NEXT
INSPECT IGNITION SWITCH ASSEMBLY
(a) Disconnect the ignition switch assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
5 (AM2) - 7 (ST2)
Ignition switch position not START
10 kΩ or higher
Ignition switch position START
Below 1 Ω
NG
REPLACE IGNITION SWITCH ASSEMBLY
OK
READ VALUE USING TECHSTREAM (STARTER SIGNAL)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
(e) Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
OK:
Ignition Switch Position
Starter Signal
ON
OFF
START
ON
Result
Result
Proceed to
NG
A
OK
B
B
CHECK FOR INTERMITTENT PROBLEMS
A
REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM)
NEXT
CHECK WHETHER DTC OUTPUT RECURS
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear DTCs (See page ).
(e) Drive the vehicle at more than 20 km/h for over 20 seconds.
(f) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.