Power Steering Pressure Sensor Circuit (P0550,P0552,P0553)
In this manual: Engine, Hybrid System
13steps
~78min
3/5difficulty
Done 0 of 13
DESCRIPTION
The power steering oil pressure sensor is turned ON when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.
DTC No.
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
Open or short in power steering oil pressure sensor circuit
Power steering oil pressure sensor
ECM
P0552
Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
Open or short in power steering oil pressure sensor circuit
Power steering oil pressure sensor
ECM
P0553
Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
Open or short in power steering oil pressure sensor circuit
Power steering oil pressure sensor
ECM
MONITOR DESCRIPTION
The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores a DTC.
MONITOR STRATEGY
Related DTCs
P0550: Power steering pressure sensor range check (Chattering)
P0552: Power steering pressure sensor range check (Low Resistance)
P0553: Power steering pressure sensor range check (High Resistance)
Required sensors/Components (Main)
Power steering oil pressure sensor
Frequency of operation
Continuous
Duration
0.5 seconds
MIL operation
Immediate
Sequence of operation
None
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Starter
OFF
Time after starter signal ON to OFF
2 seconds or more
TYPICAL MALFUNCTION THRESHOLDS
P0550
Power steering oil pressure sensor voltage
Less than 0.28 V, or more than 4.9 V
P0552
Power steering oil pressure sensor voltage
Less than 0.28 V
P0553
Power steering oil pressure sensor voltage
More than 4.9 V
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 5 seconds [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0550, P0552 or P0553.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
HINT:
If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
(a) Disconnect the ECM connector.
(b) Disconnect the power steering oil pressure sensor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D46-2 (PSP) - D74-72 (PSP)
Always
Below 1 Ω
D46-1 (VC) - D74-67 (VCV1)
Always
Below 1 Ω
D46-3 (E2) - D74-98 (E2)
Always
Below 1 Ω
D46-2 (PSP) or D74-72 (PSP) - Body ground
Always
10 kΩ or higher
D46-1 (VC) or D74-67 (VCV1) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK TERMINAL VOLTAGE (POWER SOURCE OF POWER STEERING OIL PRESSURE SENSOR)
(a) Disconnect the power steering oil pressure sensor connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D46-2 (PSP) - D46-3 (E2)
Ignition switch ON
4.5 to 5.5 V
NG
REPLACE ECM
OK
REPLACE POWER STEERING OIL PRESSURE SENSOR
(a) Replace the power steering oil pressure sensor (See page ).
NEXT
CONFIRM WHETHER DTC OUTPUT RECURS
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
(e) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.