Insufficient Coolant Temperature for Closed Loop Fuel Control (P0125)
In this manual: Engine, Hybrid System
16steps
~96min
4/5difficulty
Done 0 of 16
DESCRIPTION
Refer to DTC P0115 (See page ).
DTC No.
DTC Detection Condition
Trouble Area
P0125
Engine Coolant Temperature (ECT) does not reach closed-loop enabling temperature for 20 minutes (this period varies with engine start ECT)
(2 trip detection logic)
ECT sensor
Cooling system
Water inlet with thermostat sub-assembly
MONITOR DESCRIPTION
The resistance of the ECT sensor varies in proportion to the actual ECT. The ECM supplies a constant voltage to the sensor and monitors the signal output voltage of the sensor. The signal output voltage varies according to the changing resistance of the sensor. After the engine is started, the ECT is monitored through this signal. If the ECT sensor indicates that the engine is not yet warm enough for closed-loop fuel control despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.
Example:
The ECT is 0 °C at engine start. After about 1 minute of running time, the ECT sensor still indicates that the engine is not warm enough to begin closed-loop fuel (air-fuel ratio feedback) control. The ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.
MONITOR STRATEGY
Related DTCs
P0125: Insufficient engine coolant temperature for closed-loop fuel control
Required Sensors/Components (Main)
Water inlet with thermostat sub-assembly, Cooling system
Required Sensors/Components (Related)
Engine coolant temperature sensor and mass air flow meter
Frequency of Operation
Once per driving cycle
Duration
53 seconds: Engine coolant temperature at engine start is (closed-loop engine coolant temperature - 8,3 °C or higher)
105 seconds: Engine coolant temperature at engine start is (closed-loop engine coolant temperature - 19,4 °C [35°F]) or higher, and less than (closed-loop engine coolant temperature - 8,3 °C [15°F])
20 minutes: Engine coolant temperature at engine start is less than (closed-loop engine coolant temperature - 19,4 °C [35°F])
MIL Operation
2 driving cycles
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
P0101, P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0128 (Thermostat)
TYPICAL MALFUNCTION THRESHOLDS
Engine coolant temperature
53 seconds: Engine coolant temperature at engine start is (closed-loop engine coolant temperature - 8,3 °C or higher)
105 seconds: Engine coolant temperature at engine start is (closed-loop engine coolant temperature - 19,4 °C [35°F]) or higher, and less than (closed-loop engine coolant temperature - 8,3 °C [15°F])
20 minutes: Engine coolant temperature at engine start is less than (closed-loop engine coolant temperature - 19,4 °C [35°F])
CONFIRMATION DRIVING PATTERN
Leave the vehicle outside overnight.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp.
Check that the engine coolant temperature is 10 °C or less.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Wait 21 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0125.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
Refer to DTC P0115 (See page ).
HINT:
If DTC P0115, P0116, P0117 or P0118 is stored simultaneously with DTC P0125, the Engine Coolant Temperature (ECT) sensor may have an open or short circuit. Troubleshoot those DTCs first.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0125)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read DTCs.
Result
Result
Proceed to
P0125 is output
A
P0125 and other DTCs are output
B
HINT:
If any DTCs other than P0125 are output, troubleshoot those DTCs first.
B
GO TO DTC CHART
A
INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
(a) Remove the water inlet with thermostat sub-assembly (See page ).
(b) Check the valve opening temperature of the thermostat.
Standard opening temperature:
80 to 84 °C
HINT:
In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.
NG
REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
OK
CHECK COOLING SYSTEM
(a) Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page ).