DTC P0403 is set when the ignition switch is in the ON position.
MONITOR DESCRIPTION
This DTC is designed to detect an open or short in the EGR valve assembly circuit.
If the EGR terminal voltage is low when the EGR terminal output is off, the ECM determines that the EGR valve circuit is malfunctioning.
MONITOR STRATEGY
Related DTCs
P0403: Exhaust gas recirculation control circuit range check
Required Sensors/Components (Main)
EGR valve
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs not present
None
Engine
Running
Battery voltage
10.5 V or higher
Starter
OFF
TYPICAL MALFUNCTION THRESHOLDS
One of the following conditions is met:
Condition 1, 2, 3 or 4
1: Both conditions are met:
Condition A and B
A: Motor phase 1 output terminal voltage
Low
B: Either condition is met:
-
Motor
Driving
Motor phase 1
Not operating
2: Both conditions are met:
Condition A and B
A: Motor phase 2 output terminal voltage
Low
B: Either condition is met:
-
Motor
Driving
Motor phase 2
Not operating
3: Both conditions are met:
Condition A and B
A: Motor phase 3 output terminal voltage
Low
B: Either condition is met:
-
Motor
Driving
Motor phase 3
Not operating
4: Both conditions are met:
Condition A and B
A: Motor phase 4 output terminal voltage
Low
B: Either condition is met:
-
Motor
Driving
Motor phase 4
Not operating
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on [A].
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page ).
Start the engine and warm it up [B].
Drive the vehicle at 20 km/h or more for 10 minutes [C].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0403.
Check the DTC judgment result.
Techstream Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
Refer to DTC P0401 (See page ).
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE EGR VALVE)
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 75 °C or higher.
HINT:
When performing the Active Test, make sure the shift lever is in P or N.
The A/C switch and all accessory switches should be off.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
(e) Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
HINT:
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
OK:
MAP and idling condition change in response to EGR step position as follows.
Standard:
-
EGR Step Position (Active Test)
0 Steps
0 to 30 Steps
Idling condition
Steady idling
Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg)
MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed
OK
CHECK FOR INTERMITTENT PROBLEMS
NG
INSPECT EGR VALVE ASSEMBLY
(a) Inspect the EGR valve assembly (See page ).
HINT:
Perform "Inspection After Repair" after replacing the EGR valve assembly (See page ).
NG
REPLACE EGR VALVE ASSEMBLY
OK
INSPECT EGR VALVE ASSEMBLY (+B OR +B2 VOLTAGE)
(a) Disconnect the EGR valve assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D85-5 (+B1) - Body ground
Ignition switch ON
11 to 14 V
D85-2 (+B2) - Body ground
Ignition switch ON
11 to 14 V
(c) Reconnect the EGR valve assembly connector.
NG
GO TO STEP 6
OK
CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)
(a) Disconnect the EGR valve assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
D74-48 (EGR1) - D85-4 (EGR1)
Always
Below 1 Ω
D74-1 (EGR2) - D85-3 (EGR2)
Always
Below 1 Ω
D74-24 (EGR3) - D85-6 (EGR3)
Always
Below 1 Ω
D74-47 (EGR4) - D85-1 (EGR4)
Always
Below 1 Ω
Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
D74-48 (EGR1) or D85-4 (EGR1) - Body ground
Always
10 kΩ or higher
D74-1 (EGR2) or D85-3 (EGR2) - Body ground
Always
10 kΩ or higher
D74-24 (EGR3) or D85-6 (EGR3) - Body ground
Always
10 kΩ or higher
D74-47 (EGR4) or D85-1 (EGR4) - Body ground
Always
10 kΩ or higher
(d) Reconnect the EGR valve assembly connector.
(e) Reconnect the ECM connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK WHETHER DTC OUTPUT RECURS (DTC P0403)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON and turn the Techstream on.
(c) Clear DTCs (See page ).
(d) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
(e) Confirm that no DTC is set using the Techstream.
Result
Result
Proceed to
DTC P0403 output
A
No DTC output
B
A
REPLACE ECM
B
END
CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - EGR VALVE ASSEMBLY)
(a) Disconnect the EGR valve assembly connector.
(b) Remove the integration relay from engine room relay block.
(c) Measure the resistance according to the value(s) in the table below.