Secondary Air Injection System Pump Stuck On Bank1 (P2444-P2447)
In this manual: Engine, Hybrid System
18steps
~108min
4/5difficulty
Done 0 of 18
DESCRIPTION
Refer to P2440 (See page ).
DTC No.
DTC Detection Condition
Trouble Area
P2444
P2446
Secondary air pressure more than 3.0 kPa (23 mmHg) despite ECM commanding air pump to turn off
(2 trip detection logic)
Short in air pump circuit
Open or short in pressure sensor circuit
Pressure sensor (Air switching valve assembly)
Air injection control driver (AID)
ECM
P2445
P2447
Secondary air pressure less than 1.9 kPa (14 mmHg) despite ECM commanding air pump to turn on
(2 trip detection logic)
Air pump assembly
Open in air pump circuit
Air injection system piping
Pressure sensor (Air switching valve assembly)
Open or short in pressure sensor circuit
Air injection control driver (AID)
EGR valve assembly
Open or short in air pump heater circuit
Air pump heater relay (AI HTR)
ECM
When secondary air injection is on, the amount of air from the air pump is below the threshold
(2 trip detection logic)
MONITOR DESCRIPTION
The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the Air Switching Valve (ASV) of the Secondary Air Injection (AIR) system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.
If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and stores a DTC:
The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump.
The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump.
P2431, P2432, P2433, P2436, P2437, P2438 (Secondary Air Injection System Pressure Sensor)
Battery voltage
11 V or more
Atmospheric pressure
45 kPa (338 mmHg) or more
Engine
Running
AIR monitor during AIR: ON*1
Completed
AIR monitor during AIR: OFF*2
Completed
AIR injection driver fail (open/short or out of range)
Not detected
AIR pressure sensor fail (open/short or out of range)
Not detected
*1: AIR monitor during AIR: ON
-
Time after AIR in operation
5 seconds or more
AIR pump
ON
AIR valve
Open
Engine speed
400 to 3750 rpm
Intake air amount
Less than 100 gm/s
Time after engine start
1 second or more
*2: AIR monitor during AIR: OFF
-
Time after AIR in operation
10 seconds or more
AIR pump
OFF
AIR valve
Close
Engine speed
Below 3000 rpm
AIR monitor during AIR: ON
Completed
Time after engine start
1 second or more
P2445, P2447 AIR insufficient
Battery voltage
11 V or higher
Atmospheric pressure
45 kPa (338 mmHg) or higher
Engine
Running
Air flow pattern check condition during AIR monitor during AIR: ON*
Completed
AIR injection driver fail (open/short or out of range)
Not detected
AIR pressure sensor fail (open/short or out of range)
Not detected
*: Air flow pattern check condition during AIR monitor during AIR: ON
-
AIR valve
Open
Time after secondary air injection in operation
1 second or more
TYPICAL MALFUNCTION THRESHOLDS
Secondary Air Injection ON (Condition 1)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
18 kPa or higher
AIR pressure
1.9 kPa or higher
Secondary Air Injection ON (Condition 2)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
18 kPa or higher
AIR pressure
Below 1.9 kPa
Secondary Air Injection ON (Condition 3)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 18 kPa
AIR pressure
1.9 kPa or higher
Secondary Air Injection ON (Condition 4)
Both conditions are met during AIR ON
-
Cumulative pressure pulsation
Below 18 kPa
AIR pressure
Below 1.9 kPa
Secondary Air Injection OFF (Condition 1)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
25 kPa or higher
AIR pressure
3 kPa or higher
Secondary Air Injection OFF (Condition 2)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
25 kPa or higher
AIR pressure
Below 3 kPa
Secondary Air Injection OFF (Condition 3)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 25 kPa
AIR pressure
3 kPa or higher
Secondary Air Injection OFF (Condition 4)
Both conditions are met during AIR OFF
-
Cumulative pressure pulsation
Below 25 kPa
AIR pressure
Below 3 kPa
P2444, P2446 AIR pump is stuck ON
Either condition is met
(a) or (b)
(a) AIR OFF Condition 1
Met
(b) AIR OFF Condition 3
Met
P2445, P2447 AIR pump is stuck OFF
Either condition is met
(a) or (b)
(a) AIR ON Condition 2
Met
(b) AIR ON Condition 4
Met
P2445, P2447 AIR insufficient
Either condition is met
(a) or (b)
(a) Air flow value at Bank 1 or Bank 2
160 L/min. or less
(b) Air flow value at Bank 1 and Bank 2
160 L/min. or less
MONITOR RESULT
Refer to Checking Monitor Status (See page ).
CONFIRMATION DRIVING PATTERN
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (if set) (See page ).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
Perform the following to confirm the AIR system pending codes: Press ENTER (Exit).
Check for pending DTCs.
OK:
No pending DTC is output.
After the "Secondary air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2444, P2445, P2446 or P2447.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If no permanent DTC is output, the system is normal.
If a permanent DTC is output, the system is malfunctioning.
Turn the ignition switch off.
WIRING DIAGRAM
Refer to DTC P0412 (See page ).
HINT:
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
HINT:
Determination by ECM monitoring:
The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.
The following 8 patterns are AIR system pressure conditions in the AIR system passage.
Pressure Condition in Secondary Air Injection System Case 1
Air Pump
ON
Air Switching Valve
Open
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 2
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 3
Air Pump
ON
Air Switching Valve
Closed
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected
Pressure Condition in Secondary Air Injection System Case 4
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation not detected
Pressure Condition in Secondary Air Injection System Case 5
Air Pump
ON
Air Switching Valve
Open
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 6
Air Pump
OFF
Air Switching Valve
Open
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation detected
Pressure Condition in Secondary Air Injection System Case 7
Air Pump
ON
Air Switching Valve
Closed
Pressure
1.9 kPa or more
Pulsation Detection
Exhaust gas pulsation not detected
Pressure Condition in Secondary Air Injection System Case 8
Air Pump
OFF
Air Switching Valve
Closed
Pressure
Less than 3.0 kPa
Pulsation Detection
Exhaust gas pulsation not detected
If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.
HINT:
The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
HINT:
In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 18 to 25 kPa).
In case 1, the average pressure is approximately 3 to 11 kPa. The value of 1.9 kPa indicated in the table above is a threshold for detecting pump malfunctions.
Detected Condition while AIR Operating:
Air Pump ON, ASV Open
Detected Condition while AIR not Operating:
Air Pump OFF, ASV Closed
ECM Determination
DTC Output
Case 1
Case 8
Normal
-
Case 1
Case 6
ASV stuck open
P2440
or
P2442
Case 1
Case 7
Air pump stuck ON
P2444
or
P2446
Case 2
Case 8
Air pump stuck OFF
P2445
or
P2447
Case 3
Case 8
ASV stuck closed
P2441
or
P2443
Case 1
Case 5
ASV stuck open and air pump stuck ON
P2440 and P2444
or
P2442 and P2446
Case 2
Case 6
ASV stuck open and air pump stuck OFF
P2440 and P2445
or
P2442 and P2447
Case 3
Case 7
ASV stuck closed and air pump stuck ON
P2441 and P2444
or
P2443 and P2446
Case 4
Case 8
ASV stuck closed and air pump stuck OFF
P2441 and P2445
or
P2443 and P2447
HINT:
By using the Techstream to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
System Check:
The pressure in the secondary air passage can be checked using the Techstream.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.
Standard:
Tester Operation
Air Pump
ASV
Pressure*1
Pulsation*2
AIR PUMP: ON, ASV: OPEN
ON
OPEN
1.9 kPa or more
18 kPa or more
AIR PUMP: OFF, ASV: CLOSE
OFF
CLOSE
Less than 3.0 kPa
Less than 25 kPa
*1: Average pumping pressure (gauge pressure). The pressure should be 1.9 kPa or more when the AIR system operates.
*2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
Turn the ignition switch off.
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444, P2445, P2446 AND/OR P2447)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read DTCs.
Result
Result
Proceed to
P2444, P2445, P2446 and/or P2447 is output
A
P2444, P2445, P2446 and/or P2447 and P0418 and/or P0419 are output
B
P2444, P2445, P2446 and/or P2447 and other DTCs (except P0418 and P0419) are output
C
If any DTCs other than P0418, P0419, P2444, P2445, P2446 and/or P2447 are output, troubleshoot those DTCs first.
B
GO TO AIR PUMP INSPECTION PROCEDURE
C
GO TO DTC CHART
A
PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMP HEATER)
(a) Disconnect the air pump assembly (for bank 1 or bank 2) connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON and turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Condition
Specified Condition
D89-1 (APH+) - Body ground
Activate the Air Pump Heater is ON
11 to 14 V
D90-1 (APH+) - Body ground
Activate the Air Pump Heater is ON
11 to 14 V
(f) Reconnect the air pump assembly (for bank 1 or bank 2) connector.
NG
GO TO STEP 4
OK
INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2) (HEATER RESISTANCE)
(a) Inspect the air pump assembly (for bank 1 or bank 2) (See page ).
NG
REPLACE AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
OK
INSPECT AIR PUMP HEATER (AI-HTR) RELAY
NG
REPLACE AIR PUMP HEATER (AI-HTR) RELAY
OK
CHECK AIR PUMP HEATER (AI HTR) RELAY (POWER SOURCE)
(a) Remove the air pump heater (AI HTR) relay.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage
Tester Connection
Condition
Specified Condition
AI HTR relay terminal 5 - Body ground
Always
11 to 14 V
(c) Reinstall the air pump heater (AI HTR) relay.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODY GROUND)
(a) Remove the air pump heater (AI HTR) relay.
(b) Disconnect the air pump assembly (for bank 1 or bank 2) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance
Tester Connection
Condition
Specified Condition
AI HTR relay terminal 3 - D89-1 (APH+)
Always
Below 1 Ω
AI HTR relay terminal 3 - D90-1 (APH+)
Always
Below 1 Ω
D89-3 (APHG) - Body ground
Always
Below 1 Ω
D90-3 (APHG) - Body ground
Always
Below 1 Ω
AI HTR relay terminal 3 or D89-1 (APH+) - Body ground
Always
10 kΩ or higher
AI HTR relay terminal 3 or D90-1 (APH+) - Body ground
Always
10 kΩ or higher
(d) Reinstall the air pump heater relay (AI HTR).
(e) Reconnect the air pump assembly (for bank 1 or bank 2) connector.
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
(a) Start the engine and warm it up.
(b) Turn the ignition switch off.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON.
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(g) Start the engine.
(h) Perform the AIR system intrusive operation while the engine is idling.
(i) Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.
Standard:
Tester Operation
AIR PUMP
ASV
PRESSURE*
AIR PUMP: ON, ASV: OPEN
ON
ON
1.9 kPa or more
AIR PUMP: OFF, ASV: CLOSE
OFF
OFF
Less than 3.0 kPa
*: Average pumping pressure. The pressure should be 1.9 kPa or more when the AIR system operates.
(j) Turn the ignition switch off.
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
(g) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
(h) Start the engine after the Techstream initialization is finished.
(i) Perform the System Check operation by pressing ENTER (Next).
(j) After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
(k) Check pending DTCs.
(l) Turn the ignition switch off.
NOTICE:
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Result
Result
Proceed to
P2444, P2445, P2446 and/or P2447 is output
A
No pending DTC is output
B
B
CHECK FOR INTERMITTENT PROBLEMS
A
CHECK VACUUM HOSE (PRESSURE SENSOR - AIR SWITCHING VALVE)
(a) Check the vacuum hose connections with the pressure sensor and air switching valve assembly.
(b) Inspect the vacuum hose for blockages and damage.
OK:
Vacuum hose has no blockages or damage.
NG
REPAIR OR REPLACE VACUUM HOSE
OK
INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).
(e) Check the pressure displayed on the Techstream.
Standard pressure:
45 to 135 kPa
HINT:
The Techstream displays the air pump pressure as absolute pressure.
Result
Result
Proceed to
OK
A
NG (for Bank 1)
B
NG (for Bank 2)
C
B
REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 1)
C
REPLACE AIR SWITCHING VALVE ASSEMBLY (FOR BANK 2)
A
CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS
(a) Check that all the pipes and hoses between the air pump and ASV are securely connected.
(b) Inspect the pipes and hoses for blockages and damage.
OK:
AIR system piping has no blockages or damage.
NG
REPAIR OR REPLACE SECONDARY AIR INJECTION SYSTEM PIPING
OK
INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
(a) Disconnect the air injection control driver (for bank 1 or bank 2) connectors.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D50-1 (E) - Body ground
Always
Below 1 Ω
D54-1 (E2) - Body ground
Always
Below 1 Ω
(c) Turn the ignition switch to ON.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
D48-1 (BATT) - Body ground
Always
11 to 14 V (near battery voltage)
D50-5 (+B) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
D52-1 (BAT2) - Body ground
Always
11 to 14 V (near battery voltage)
D54-5 (+B2) - Body ground
Ignition switch ON
11 to 14 V (near battery voltage)
NG
REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT
OK
CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
(a) Disconnect the ECM connector.
(b) Disconnect the air injection control driver (for bank 1 or bank 2) connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
D74-54 (AIRP) - D50-4 (SIP)
Always
Below 1 Ω
D74-53 (ARP2) - D54-4 (SIP2)
Always
Below 1 Ω
D74-54 (AIRP) or D50-4 (SIP) - Body ground
Always
10 kΩ or higher
D74-53 (ARP2) or D54-4 (SIP2) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
INSPECT AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
(a) Start the engine and warm it up.
(b) Turn the ignition switch off.
(c) Connect the 400 A probe of an ammeter to the (+) wire of the air pump.
(d) Connect the Techstream to the DLC3.
(e) Turn the ignition switch to ON and turn the Techstream ON.
(f) Start the engine.
(g) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(h) Measure the current while the air pump is on and off.
Standard Current:
Tester Operation
Air Pump
ASV
Specified Condition
AIR PUMP: ON, ASV: OPEN
ON
OPEN
10 to 40 A
AIR PUMP: OFF, ASV: CLOSE
OFF
CLOSE
Below 1 A
NOTICE:
This Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.
Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.
While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).
If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.
Performing the Secondary Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK
GO TO STEP 17
NG
REPLACE AIR PUMP ASSEMBLY (FOR BANK 1 OR BANK 2)
(a) Replace the air pump assembly (for bank 1 or bank 2) (See page ).
(g) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
(h) Start the engine after the Techstream initialization is finished.
(i) Perform the System Check operation by pressing ENTER (Next).
(j) After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
(k) Check pending DTCs.
OK:
No pending DTC is output.
(l) Turn the ignition switch off.
NOTICE:
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK
END
NG
PERFORM ACTIVE TEST USING TECHSTREAM
(a) Disconnect the air injection control driver (for bank 1 or bank 2) connector.
(b) Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the air injection control driver (AID).
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to ON and turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(f) Start the engine.
(g) Perform the AIR system forced operation while the engine is idling.
(h) Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
(i) Turn the ignition switch off.
NOTICE:
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Standard Voltage:
Tester Connection
Condition
Specified Condition
D50-3 (SIV) - D50-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D54-3 (SIV2) - D54-1 (E2)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D50-3 (SIV) - D50-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
D54-3 (SIV2) - D54-1 (E2)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
(j) Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the air injection control driver.
(k) Connect the Techstream to the DLC3.
(l) Turn the ignition switch to ON and turn the Techstream on.
(m) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
HINT:
When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(n) Start the engine.
(o) Perform the AIR system forced operation while the engine is idling.
(p) Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
(q) Turn the ignition switch off.
NOTICE:
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
Standard Voltage:
Tester Connection
Condition
Specified Condition
D50-4 (SIP) - D50-1 (E)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D54-4 (SIP2) - D54-1 (E2)
AIR PUMP: ON, ASV: OPEN
0.5 to 2 V
D50-4 (SIP) - D50-1 (E)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
D54-4 (SIP2) - D54-1 (E2)
AIR PUMP: OFF, ASV: CLOSE
11 to 14 V
NG
REPLACE ECM
OK
REPLACE AIR INJECTION CONTROL DRIVER (FOR BANK 1 OR BANK 2)
(a) Replace the air injection control driver (for bank 1 or bank 2) (See page ).
(g) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
(h) Start the engine after the Techstream initialization is finished.
(i) Perform the System Check operation by pressing ENTER (Next).
(j) After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
(k) Check pending DTCs.
OK:
No pending DTC is output.
(l) Turn the ignition switch off.
NOTICE:
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
OK
END
NG
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 75 °C or higher.
HINT:
When performing the Active Test, make sure the shift lever is in P or N.
The A/C switch and all accessory switches should be off.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position.
(e) Confirm the Throttle Idle Position is ON and check the engine idling condition and MAP values in the Data List while performing the Active Test.
HINT:
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
OK:
MAP and idling condition change in response to EGR step position as follows.
Standard:
-
EGR Step Position (Active Test)
0 Steps
0 to 30 Steps
Idling condition
Steady idling
Idling changes from steady to rough idling or engine stall
MAP
(Data List)
20 to 40 kPa (150 to 300 mmHg)
MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed
OK
REPLACE ECM
NG
INSPECT EGR VALVE ASSEMBLY
(a) Remove the EGR valve assembly (See page ).
(b) Check if the EGR valve is stuck open.
OK:
EGR valve is tightly closed.
HINT:
Perform "Inspection After Repair" after repairing or replacing the EGR valve assembly (See page ).