DESCRIPTION
The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
WIRING DIAGRAM
PROCEDURE
INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)
(a) Disconnect the fuel injector assembly connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Cylinder | Tester Connection | Switch Condition | Specified Condition |
No. 1 |
H1-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 2 |
F1-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 3 |
H2-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 4 |
F2-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 5 |
H3-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 6 |
F3-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 7 |
H4-2 - Ground |
Ignition switch ON |
11 to 14 V |
No. 8 |
F4-2 - Ground |
Ignition switch ON |
11 to 14 V |
| NG |
 |
GO TO STEP 4 |
| OK |
 |
|
INSPECT FUEL INJECTOR ASSEMBLY
(a) Inspect the fuel injector assembly (See page ).
HINT:
Perform "Inspection After Repair" after replacing the fuel injector assembly (See page ).
| NG |
 |
REPLACE FUEL INJECTOR ASSEMBLY |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
(a) Disconnect the fuel injector assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Cylinder | Tester Connection | Condition | Specified Condition |
No. 1 |
H1-1 - Ground |
Always |
10 kΩ or higher |
H1-1 - D74-86 (#10) |
Always |
Below 1 Ω |
No. 2 |
F1-1 - Ground |
Always |
10 kΩ or higher |
F1-1 - D74-109 (#20) |
Always |
Below 1 Ω |
No. 3 |
H2-1 - Ground |
Always |
10 kΩ or higher |
H2-1 - D74-85 (#30) |
Always |
Below 1 Ω |
No. 4 |
F2-1 - Ground |
Always |
10 kΩ or higher |
F2-1 - D74-108 (#40) |
Always |
Below 1 Ω |
No. 5 |
H3-1 - Ground |
Always |
10 kΩ or higher |
H3-1 - D74-84 (#50) |
Always |
Below 1 Ω |
No. 6 |
F3-1 - Ground |
Always |
10 kΩ or higher |
F3-1 - D74-107 (#60) |
Always |
Below 1 Ω |
No. 7 |
H4-1 - Ground |
Always |
10 kΩ or higher |
H4-1 - D74-83 (#70) |
Always |
Below 1 Ω |
No. 8 |
F4-1 - Ground |
Always |
10 kΩ or higher |
F4-1 - D74-106 (#80) |
Always |
Below 1 Ω |
| OK |
 |
REPLACE ECM |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT FUSES (INJ, IG2 MAIN)
(a) Remove the INJ fuse and IG2 MAIN fuse from the engine room relay block.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
INJ fuse |
Always |
Below 1 Ω |
IG2 MAIN fuse |
Always |
Below 1 Ω |
| NG |
 |
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE |
| OK |
 |
|
INSPECT INTEGRATION RELAY (IG2)
(a) Inspect the integration relay (See page ).
| OK |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY) |
| NG |
 |
REPLACE INTEGRATION RELAY |
|