Internal Control Module A/D Processing Performance (P060B)
In this manual: Engine, Hybrid System
12steps
~72min
3/5difficulty
Done 0 of 12
DESCRIPTION
This DTC is output when a communication error occurs in the ECM.
DTC No.
DTC Detection Condition
Trouble Area
P060B
ECM main CPU communication error
(1 trip detection logic)
ECM
Knock sensor
MONITOR STRATEGY
Related DTCs
P060B: ECM main CPU communication error
Required sensors/Components (Main)
ECM
Required sensors/Components (Related)
-
Frequency of operation
Once per driving cycle
Duration
2 times: Case 2
10 times: Case 1
30 times: Case 3 and 4
MIL operation
Immediate
Sequence of operation
None
TYPICAL ENABLING CONDITIONS
Case 1 and 4
Monitor runs whenever following DTCs not present
None
Both of the following conditions are met
-
Battery voltage
8 V or more
Starter
OFF
Case 2 and 3
Monitor runs whenever following DTCs not present
None
TYPICAL MALFUNCTION THRESHOLDS
Case 1
Internal control module serial communication
Fail
Case 2
AD converter
Fail
Case 3
Knock sensor circuit
Fail
Case 4
Knock sensor serial communication
Fail
CONFIRMATION DRIVING PATTERN
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Wait 16 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
HINT:
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P060B.
Check the DTC judgment result.
Tester Display
Description
NORMAL
DTC judgment completed
System normal
ABNORMAL
DTC judgment completed
System abnormal
INCOMPLETE
DTC judgment not completed
Perform driving pattern after confirming DTC enabling conditions
N/A
Unable to perform DTC judgment
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
NOTICE:
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page ).
HINT:
Read freeze frame data using a Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK FOR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear DTCs (See page ).
(e) Turn the Techstream off.
(f) Turn the ignition switch off.
(g) Disconnect the Techstream.
(h) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(i) Connect the cable to the negative (-) battery terminal.
(j) Connect the Techstream to the DLC3.
(k) Turn the ignition switch to ON and turn the Techstream on.
(l) Wait 16 seconds or more.
(m) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(n) Check for DTCs.
Result
Result
Proceed to
DTC is not output
A
DTC P060B is output
B
DTC P060B and P0327, P0328, P032C, P032D, P0332, P0333, P033C or P033D are output
C
A
CHECK FOR INTERMITTENT PROBLEMS
B
REPLACE ECM
C
GO TO DTC (P0327, P0328, P032C, P032D, P0332, P0333, P033C OR P033D)