BMW X3 Quiz

Final drive mounting

In this manual: Final drive mounting
General information on preservation measures — 1Body cavity sealing — 1Body corrosion protection — 1Body repair instructions — 1Support members — 1Luggage compartment floor — 1Wheel wells — 1Side frame and door pillars — 1Roof outer skin — 1Dash cowl — 1Front trim panel — 1Rear trim panel — 1Side panels — 1Front side doors — 1Rear side doors — 1Front lid — 1Rear lid — 1Other flaps — 1Body special tools — 1General information — 1Handling brake fluids — 1Brake testing and bleeding — 1Front brakes — 1Rear brakes — 1Master brake cylinder — 1Brake lines — 1Brake booster — 1Electrical components/wear indicator — 1Parking brake — 1Mechanical/hydraulic components — 1Electronic components — 1Brakes — 1Front brake — 1Pedal mounting block — 1Brake pedal with linkage — 1Clutch pedal with linkage — 1Accelerator pedal actuation — 1Pedals — 1Specified grease — 1Propeller shaft, general — 1Propeller shaft assembly — 1Center console assembly — 1Front propeller shaft — 1Propeller shaft — 1Propeller shaft complete — 1Front axle repair instructions — 1Front axle suspension — 1Front sub-frame — 1Struts with rubber mounts — 1Wheel bearings and stub axle — 1Spring strut — 1Spring with suspension — 1Stabilizer bar — 1Front axle gearbox — 1Output shaft — 1Front axle — 1General information on high temperature multi-purpose grease — 1Rear axle repair instructions — 1Final drive with cover — 1Final drive mounting — 1Output shafts — 1Rear sub-frame — 1Control arms and struts — 1Axle mounting — 1Wheel bearings — 1Shock absorber — 1With suspension — 1Stabilizer bar — 1Rear axle — 1General information on final drive oil — 1Approved final drive oils for front and rear axle final drives with and without limited slip or viscous coupling — 1Final drive oil for bmw m1 motorsport coupe — 1Operating fluids as of 11/2015 — 1Brake pad replacement reminder — 1Emissions maintenance reminder — 1Maintenance service reminder — 1Tire pressure monitor system reminder — 1Description — 1Troubleshooting — 1Ignition wires, spark plugs — 1Ignition coil — 1Electronic switching or control units — 1Preheating relay — 1Preheater plugs — 1Alternator with drive and mounting — 1Controller — 1Starter with mounting — 1Starter lead — 1Engine wiring loom — 1Oil pressure/oil temperature/oil gauge — 1Switches and relays — 1Engine electrical system — 1Cabin air filter — 1Cabin air filter applications — 1Operating fluids - air conditioning and heating — 1Air conditioner refrigerant — 1Refrigeration oil — 1Note, overview components climate control — 1Heater with operation — 1Auxiliary. heater with control elements — 1Nozzles and outlets — 1Microfilter — 1Air conditioning, leak detection — 1Ac housing/evaporator, switching elements — 1Compressor — 1Condenser and dryer with lines — 1Heating and air conditioning — 1Front axle repair instructions — 1Front axle suspension — 1Front sub-frame — 1Struts with rubber mounts — 1Wheel bearings and stub axle — 1Spring strut — 1Spring with suspension — 1Stabilizer bar — 1Front axle gearbox — 1Front axle — 1General information on high temperature multi-purpose grease — 1Integrated suspension systems repair instructions — 1Front control and suspension elements — 1Rear control and suspension elements — 1Electrical components — 1Electronic damping force adjustment — 1Integrated suspension systems — 1Approved hydraulic fluids — 1Rear axle repair instructions — 1Final drive — 1Final drive with cover — 1Final drive mounting — 1Output shafts — 1Rear sub-frame — 1Control arms and struts — 1Axle mounting — 1Wheel bearings — 1Shock absorber — 1Springs with suspension — 1Stabilizer bar — 1Rear axle — 1General information on final drive oil — 1Approved final drive oils for front and rear axle final drives with and without limited slip or viscous coupling — 1Final drive oil for bmw m1 motorsport coupe — 1Operating fluids as of 11/2015 — 1Electronic chassis alignment — 1Mechanical steering gear — 1Steering gear with servo unit — 1Steering arms, tie rods, steer. damper — 1Steering column — 1Steering wheel — 1Steering wheel for airbag — 1Pump and oil supply — 1Steering and wheel alignment — 1Wheels — 1Disc wheels (rims) — 1Tires — 1Wheels with tires — 1Tire mounting paste — 1Engine mounting — 1Transmission suspension, automatic. transmission — 1Engine and gearbox suspension — 1Transmission in general — 1Transmission case, oil sump — 1Extension housing, bearings, seal — 1Mechanical attachments — 1Hydr/el control components/elements — 1Oil pump — 1Shift valves, parking lock — 1Torque converter — 1Automatic transmission — 1Automatic transmission fluid for zf-transmission GA8HP45Z / GA8HP50Z / GA8HP70Z / GA8HP90Z / GA8P70H / GA8P75H / GA8HP75Z — 1General information on automatic transmission fluids — 1Approved automatic transmission fluids for initial fillings and correcting fluid levels — 1Checking transmission fluid level — 1Transmission fluid change intervals (if applicable) — 1Transfer case, general — 1Transfer box — 1Transmission shafts — 1Transfer box special tools — 1Transfer box in general (atc 45l) — 1Transmission in general — 1Bearing in housing, sealing ring — 1SELF-DIAGNOSTICS DTCS — 1
~5min read
  • Replace the rubber mounts for the front of the rear axle final drive suspension
  • Replacing the rubber mounts for the rear axle final drive suspension at rear

Replace the rubber mounts for the front of the rear axle final drive suspension

Special tools required:

  • 33 5 200
  • 33 5 206
  • 33 5 166
  • 33 5 163
  • 33 5 162
  • 33 5 161
  • 33 4 466
  • 33 4 465
  • 33 5 105
  • 33 5 164
  • 33 5 165

Necessary preliminary tasks:

  • Remove exhaust system .
  • Remove PROPELLER SHAFT AT FINAL DRIVE .

Position special tool 33 5 200 on workshop jack.

Support rear axle final drive unit with special tool 33 5 200 .

Lash rear axle final drive unit with tightening strap 33 5 206 to special tool 33 5 200 .

IMPORTANT: Tensioning strap 33 5 206 must be pass through between output shafts and rear axle final drive cover!

Suspension

Release screws (1).

Installation note: Adhere to the installation sequence at the end of the document in order to prevent distortion of the rear axle final drive during installation and thereby avoid potential complaints about noise.

Suspension

Slacken nut (1).

Only N47: Remove vibration absorber (2) with holder.

Installation note:

Replace nut.

Adhere to the installation sequence at the end of the document in order to prevent distortion of the rear axle final drive during installation and thereby avoid potential complaints about noise.

Suspension

Lower rear axle final drive with special tool 33 5 200 .

Suspension

Pull out rubber mount with special tools 33 5 166 , 33 5 163 , 33 5 162 , 33 5 161 , 33 4 466 and 33 4 465 .

NOTE: The milled recess of special tool 33 5 162 must point outward toward the rear axle support.

Use ratchet ring spanner 33 5 105 .

Suspension

IMPORTANT: Coat the bearing bush on the rear axle support and the new rubber mount with Circo Light.

Align rubber mount horizontally by way of slots (1).

Suspension

Insert rubber mount (1) in special tool 33 5 164 .

Draw in rubber mount (1) with special tools 33 5 165 , 33 5 164 , 33 5 163 , 33 4 466 and 33 4 465 as far as it will go.

NOTE: Use ratchet ring spanner 33 5 105 .

Suspension

Assembly sequence:

1. Insert the rear axle final drive into the rear axle support using the workshop jack and special tool 33 5 200 .

2. Insert screws (1) (do not tighten).

3. Insert bolt from rear and replace nut (2) (do not tighten down).

4. Release tensioning strap, lower special tool 33 5 200 and move away.

5. Tighten down screws (1).

6. Tighten nut (2).

Suspension

Replacing the rubber mounts for the rear axle final drive suspension at rear

Special tools required:

  • 33 5 200
  • 33 5 206
  • 33 5 153
  • 33 5 152
  • 33 5 151
  • 33 3 103
  • 33 3 104
  • 33 5 105
  • 33 5 154
  • 33 5 155
  • 33 5 156

Necessary preliminary tasks:

  • Remove exhaust system .
  • Remove PROPELLER SHAFT AT FINAL DRIVE .

Position special tool 33 5 200 on workshop jack. 33 5 200 Support rear axle final drive unit with special tool.

Lash rear axle final drive unit with tightening strap 33 5 206 to special tool 33 5 200 .

IMPORTANT: Tensioning strap 33 5 206 must be pass through between output shafts and rear axle final drive cover!

Suspension

Release screws (1).

Installation note: Adhere to the installation sequence at the end of the document in order to prevent distortion of the rear axle final drive during installation and thereby avoid potential complaints about noise.

Suspension

Slacken nut (1).

Only N47: Remove vibration absorber (2) with holder.

Installation note:

Replace nut.

Adhere to the installation sequence at the end of the document in order to prevent distortion of the rear axle final drive during installation and thereby avoid potential complaints about noise.

Suspension

Lower rear axle final drive with special tool 33 5 200 .

Suspension

Pull out rubber mount with special tools 33 5 153, 33 5 152, 33 5 151, 33 3 103 and 33 3 104 .

NOTE: Ensure that the 33 5 152 special tool is correctly seated on the rear axle support.

Use ratchet ring wrench 33 5 105 .

Suspension

IMPORTANT: Coat the bearing bush on the rear axle support and the new rubber mount with Circo Light (note BMW Parts Department).

Align rubber mount horizontally by way of elongated hole (1).

Suspension

Insert rubber mount (1) in special tool 33 5 154.

Draw in rubber mount (1) with special tools 33 5 155, 33 5 154, 33 5 156, 33 3 103 and 33 3 104 as far as it will go.

NOTE: Make sure special tools 33 5 154 and 33 5 156 contact rear axle support correctly.

Use ratchet ring spanner 33 5 105 .

Suspension

Assembly sequence:

1. Insert the rear axle final drive into the rear axle support using the workshop jack and special tool 33 5 200 .

2. Insert screws (1) (do not tighten).

3. Insert bolt from rear and replace nut (2) (do not tighten down).

4. Release tensioning strap and lower special tool 33 5 200 and move away.

5. Tighten down screws (1).

6. Tighten nut (2).

Suspension

Test yourself

A quick BMW X3 quiz: every answer comes with an explanation and a link to the manual page.