Kia Stinger CK Quiz
Engine Control System/Fuel System

Exhaust Gas Temperature Sensor (EGTS)

In this manual: Engine Control System/Fuel System
General Information — 8Maintenance — 27Engine Mechanical System — 47Engine Electrical System — 19Emission Control System — 12Engine Control System/Fuel System — 51Automatic Transmission System — 34All-Wheel Drive (AWD) System — 7Drive Shaft and Axle — 15Suspension System — 25Steering — 8Restraints — 19Brake System — 22Body (Interior and Exterior) — 47Front Seat Belt — 63Body Electrical System — 99Windshield Wiper/Washer — 11Heating, Ventilation, and Air Conditioning — 32
19steps
~114min
4/5difficulty
02040608010049.136N·mlb·ft
Tightening torque found on this page
Done 0 of 19

Specifications

Specification

Exhaust Gas Temperature Sensor (EGTS) No. 1, 2

▷ Type: Thermistor Type

Temperature [°C (°F)] Resistance (kOhm)
-40 (-40) 0,17
0 (-32) 0,201
100 (212) 0,276
200 (392) 0,35
300 (572) 0,42
400 (752) 0,489
500 (932) 0,555
600 (1112) 0,618
700 (1292) 0,68
800 (1472) 0,739
850 (1562) 0,767

Description and Operation

Description

The Exhaust Gas Temperature Sensor (EGTS) No. 1 for the WGT, installed in the exhaust manifold, measures the temperature of the exhaust gas flowing into the WGT.

The exhaust gas temperature sensor is installed in the gasoline particulate filter (GPF) assembly. The No. 2 exhaust gas temperature sensor (EGTS) for the GPF measures the temperature of the exhaust gas flowing into the GPF.

When the specified engine condition is met, the ECM burns off the soot collected in the GPF using the exhaust gas. At this time, the exhaust gas temperature is an important factor for engine condition.

Circuit Diagrams

Wiring Diagram

EGTS No. 1

Harness Connector

EGTS No. 2

Harness Connector

EGTS No. 3

Repair Procedures

Inspection

  1. Turn the ignition off.

  2. Disconnect the connector of the exhaust gas temperature sensors No. 1/No. 2/No. 3.

  3. Measure the resistance between the sensor signal terminal and the ground terminal.

  4. Make sure the resistance is within specification.

    Exhaust Gas Temperature Sensor [EGTS No. 1, No. 2, No. 3 (T3, T4, T5)]

    Temperature [°C (°F)] Resistance (kOhm)
    -40 (-40) 0,17
    0 (-32) 0,201
    100 (212) 0,276
    200 (392) 0,35
    300 (572) 0,42
    400 (752) 0,489
    500 (932) 0,555
    600 (1112) 0,618
    700 (1292) 0,68
    800 (1472) 0,739
    850 (1562) 0,767

Removal and Installation

[EGTS No. 1]

  1. Turn the ignition switch OFF and disconnect the negative (-) battery terminal.

  2. Remove the floor under cover.

  3. Disconnect the EGTS connector (A).

  4. Remove the EGTS (A).

    Exhaust Gas Temperature Sensor (EGTS):

    39,2–49 N·m

  5. Install the sensor in the reverse order of removal.

[EGTS No. 2]

  1. Turn the ignition switch OFF and disconnect the negative (-) battery terminal.

  2. Remove the floor under cover.

  3. Disconnect the EGTS connector (A).

  4. Remove the EGTS (A).

    Exhaust Gas Temperature Sensor (EGTS):

    39,2–49 N·m

  5. Install the sensor in the reverse order of removal.

[EGTS No. 3]

  1. Turn the ignition switch OFF and disconnect the negative (-) battery terminal.

  2. Remove the floor under cover.

  3. Disconnect the EGTS connector (A).

  4. Remove the EGTS (A).

    Exhaust Gas Temperature Sensor (EGTS):

    39,2–49 N·m

  5. Install the sensor in the reverse order of removal.

Test yourself

A quick Kia Stinger CK quiz: every answer comes with an explanation and a link to the manual page.