Single-Use Parts

Rear Door

57steps
~342min
4/5difficulty
0102030405011.89N·mlb·ft
Tightening torque found on this page
Done 0 of 57

Contents:

Components and Components Location

Component

Body (Interior and Exterior) — Rear Door / Components and Components Location / Component illustration
1. Rear Door Delta Inner Cover
2. Rear Door Trim
3. Rear Door Inside Handle
4. Rear Door Belt Inside Weatherstrip
5. Rear Door Belt Outside Weatherstrip
6. Rear Door Outer Delta Molding
7. Rear Door Window Glass
7-a. 7.8 - 11,8 N·m
8. Rear Door Window Glass Run
9. Rear Door Channel
9-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
9-b. 8.8 - 13,7 N·m
10. Rear Door Outside Handle Assembly
10-a. 3.9 - 5,9 N·m
11. Rear Door Module
11-a. 8.8 - 13,7 N·m
12. Rear Door Latch
12-a. 6.9 - 10,8 N·m
13. Rear Door Side Weatherstrip
14. Rear Door Body Side Weatherstrip
15. Rear Door Assembly
15-a. 21.6 - 26 N·m
15-b. 23.5 - 31 N·m

Adjustment

Adjustment

Door Adjustment
  1. Check that the gap between the door and the body is even after parking in a flat level.
    Body (Interior and Exterior) — Rear Door / Adjustment illustration
  2. Loosen the door hinge (A) bolts, adjust the door by moving it back and forth, left and right, and then tighten the bolts.
    Tightening torque (B) : 23.5 - 31 N·m (C) : 21.6 - 26 N·m
    Body (Interior and Exterior) — Rear Door / Adjustment illustration
  3. Check that the gap between the door and the body is even.
  4. Loosen the screws and adjust the striker (A) by moving it back and forth, left and right, and then tighten the screws.

    Tightening torque : 16.7 - 22 N·m

    Body (Interior and Exterior) — Rear Door / Adjustment illustration
  5. Check that the door opens and closes properly.
  6. Remove the rear door trim. (Refer Rear Door - "Rear Door Trim")
  7. Remove the rear door window glass hole plug (A).
    Body (Interior and Exterior) — Rear Door / Adjustment illustration
  8. Operate the power window switch to lower the window glass until the window glass bolt is visible in the service hole.
  9. Loosen the rear door window glass bolt (A).

    Tightening torque : 7.8 - 11,8 N·m

    Body (Interior and Exterior) — Rear Door / Adjustment illustration
  10. Adjust the gap by moving the rear door window glass (A) up, down, left and right, and then tighten the bolts.
    Body (Interior and Exterior) — Rear Door / Adjustment illustration
  11. Check that the glass operates properly.
Striker Adjustment Glass Adjustment

Rear Door Trim Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the rear door delta inner cover (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
  3. Remove the rear door screw cap (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
  4. Remove the rear door trim (A) using the service hole (B) after removing the screw.
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
  5. Separate the rear door inside handle cage (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration
    Note
    When mounting the cage on the inside handle, assemble it until there is a "click" sound.
  6. Disconnect the power window switch connector (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Trim / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Door Window Glass Removal and Installation

Removal

  1. Remove the rear door trim. (Refer Rear Door - "Rear Door Trim")
  2. Remove the rear door belt inside and outside weatherstrips (A). (Refer to Rear Door - "Rear Door Weatherstrip")
  3. Remove the rear door outer delta molding screw (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  4. Remove the rear door outer delta garnish (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  5. Loosen the rear door channel nuts (A) and bolt (B).
    Tightening torque Bolt : 8.8 - 13,7 N·m Nut : 3.9 - 5,9 N·m
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  6. Separate the rear door channel (A) in the direction of the arrow.
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  7. Remove the rear door window glass hole plug (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  8. Operate the power window switch to lower the rear window glass until the window glass bolt is visible in the service hole.
  9. Remove the rear door window glass bolt (A).

    Tightening torque : 7.8 - 11,8 N·m

    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  10. Remove the rear door window glass (A) in the direction of the arrow.
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  11. Remove the rear door channel nuts (A) and bolt (B).
    Tightening torque Bolt : 8.8 - 13,7 N·m Nut : 3.9 - 5,9 N·m
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  12. Remove the rear door channel (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration
  13. Remove the rear door glass run (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Window Glass / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Door Module Removal and Installation

Removal

  1. Remove the rear door window glass. (Refer to Rear Door - "Rear Door Window Glass")
  2. Remove the rear door outside handle. (Refer to Rear Door - "Rear Door Handle")
  3. Disconnect the rear door main wiring connector (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration
  4. Remove the rear door latch screws (A).

    Tightening torque : 6.9 - 10,8 N·m

    Body (Interior and Exterior) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration
  5. Remove the rear door handle base screw (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration
  6. Remove the rear door module (A) after removing the bolts.

    Tightening torque : 8.8 - 13,7 N·m

    Body (Interior and Exterior) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration
  7. Remove the wiring harness (A) from the rear door module.
    Body (Interior and Exterior) — Rear Door / Rear Door Module / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Door Handle Removal and Installation

Removal

Rear Door Inside Handle
  1. Remove the rear door trim. (Refer Rear Door - "Rear Door Trim")
  2. Remove the rear door inside handle (A) after removing the screws.
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  3. Remove the hole plug (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  4. Fully loosen the rear door outside handle bolt (A).
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  5. Remove the door outside handle (A) in the direction of the arrow.
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  6. Remove the rear door outside handle cover (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  7. Remove the rear door outside handle pad (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  8. Remove the rear door module. (Refer to Rear Door - "Rear Door Module")
  9. Separate the rear door handle cable (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
  10. Remove the rear door outside handle base (A) after releasing the retainer hook (B).
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Rear Door / Rear Door Handle / Removal and Installation / Removal illustration
Rear Door Outside Handle Rear Door Outside Handle Base

Installation

  1. Install in reverse order of removal.

Rear Door Latch Removal and Installation

Removal

  1. Remove the rear door outside handle base. (Refer to Rear Door - "Rear Door Handle")
  2. Disconnect the rear door latch connector (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration
  3. Remove the rear door latch (A) in the direction of the arrow after releasing the retainer hook (B).
    Body (Interior and Exterior) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration
  4. Remove the rear door inside handle cable (A) in the direction of the arrow.
    Body (Interior and Exterior) — Rear Door / Rear Door Latch / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Rear Door Weatherstrip Removal and Installation

Removal

Rear Door Side Weatherstrip
  1. Separate the rear door checker (A) after removing the bolt.

    Tightening torque : 16.7 - 22 N·m

    Body (Interior and Exterior) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration
  2. Remove the rear door side weatherstrip (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration
  3. Remove the rear door body side weatherstrip (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration
  4. Remove the rear door belt outside weather strip screw (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration
  5. Remove the rear door belt outside weatherstrip (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration
  6. Remove the rear door belt inside weatherstrip (A).
    Body (Interior and Exterior) — Rear Door / Rear Door Weatherstrip / Removal and Installation / Removal illustration
Rear Door Body Side Weatherstrip Rear Door Belt Outside Weatherstrip Rear Door Belt Inside Weatherstrip

Installation

  1. Install in reverse order of removal.