Single-Use Parts

Tailgate

42steps
~252min
4/5difficulty
0102030405026.520N·mlb·ft
Tightening torque found on this page
Done 0 of 42

Contents:

Components and Components Location

Component

Body (Interior and Exterior) — Tailgate / Components and Components Location / Component illustration
1. Tailgate Lid Upper Trim
2. Tailgate Lid Side Trim
3. Power Tailgate Switch
4. Tailgate Lid Handle Grip
5. Tailgate Lid Lower Trim
6. Tailgate Latch
6-a. 21.6 - 26 N·m
6-b. 21.6 - 32 N·m
7. Power Tailgate Buzzer
8. Power Tailgate Strip
9. Power Tailgate Drive Unit
10. Tailgate Lift
11. Tailgate Outside Handle Switch
12. Tailgate Weatherstrip
13. Tailgate Assembly
13-a. 7.8 - 11,8 N·m

Description and Operation

Description

  • Power tailgate system is an electro-mechanical system that can open and close the tailgate automatically, by using local switch (push button switch inside of the tailgate, and outside handle switch), and wireless remote key (FOB), or can halt the tailgate. The Power Tailgate Module (PTGM) sends and receives the vehicle’s information via IBU, ICU, instrument cluster and CAN communication, so that it can decide the opening/closing of the tailgate and self diagnosis.
  • There’s a safety function to reverse its direction, when an obstacle is detected during the operation of the power tailgate. Also if power mode is disabled due to discharged battery or disabled Power Tailgate Module (PTGM), manual opening/closing is possible by using the emergency lever on the tailgate latch after unlocking the tailgate.
Location and Direction of the Tailgate
  • Power Tailgate system measures the location of the tailgate through the total hall sensor inside the spindle operation unit motor.
  • Also, the moving direction of the tailgate can be confirmed through analyzing the direction of spindle operation unit motor.
  • The signal counting (location confirmation) of the hall sensor is valid both in power operation mode and general operation mode.
Component element
  1. Power Tailgate Module (PTGM) (A)
    Body (Interior and Exterior) — Tailgate / Description and Operation / Description illustration
    • PTGM is installed in the left back of luggage side trim.
    • The power tailgate module (PTGM) is to operate 2 actuators (Spindles) by using the driving motors.
  2. Power tailgate latch assembly (B)
    Body (Interior and Exterior) — Tailgate / Description and Operation / Description illustration
    Power tailgate latch assembly is installed at the end of the tailgate and operates power lock/unlock mode according to the PTGM control output.
  3. Power tailgate drive unit (C)
    Body (Interior and Exterior) — Tailgate / Description and Operation / Description illustration
    • Power tailgate drive unit controls to open/close by using the rotating power of the motor installed inside.
    • Recognizes the tailgate's driving direction by sending motor's rotating direction signal inside of PTG drive unit to PTGM.
  4. Crash pad side switch (D)
    Body (Interior and Exterior) — Tailgate / Description and Operation / Description illustration
    If the switch inside of the tailgate is pushed, the tailgate will start the power closing function.
  5. Power tailgate inner switch (E)
    Body (Interior and Exterior) — Tailgate / Description and Operation / Description illustration
    If the power tailgate inner switch is pushed, the tailgate will operate the power closing function.
  6. Power tailgate buzzer (F)
    Body (Interior and Exterior) — Tailgate / Description and Operation / Description illustration
    When an obstacle is detected or power function is not performed properly according to user's order, alarm buzzer sound will be heard.

Adjustment

Adjustment

  1. After parking the vehicle on the flat surface, check that the distance between the tailgate and the body is even.
  2. Loosen the tailgate hinge (A) bolts, adjust the gap by moving the tailgate back and forth, left and right, and then tighten the bolts.
  3. Adjust the gap between the tailgate and body by turning the overslam bumpers (B).
  4. Loosen the striker (C) screws, adjust the striker by moving the striker back and forth, left and right, and then tighten the screws.
  5. Check that the tailgate opens and closes properly.
    Body (Interior and Exterior) — Tailgate / Adjustment illustration

Tailgate Lid Trim Removal and Installation

Removal

Tailgate Lid Upper Trim
  1. Remove the tailgate lid upper trim (A).
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
  2. Remove the tailgate lid upper trim.
  3. Remove the tailgate lid side trim (A) after removing the screw.
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
  4. Remove the tailgate lid side trim.
  5. Remove the power tailgate switch. (Refer to Tailgate - "Power Tailgate Switch")
  6. Remove the tailgate lid hand grip (A).
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Note
    Reusing is prohibited after removing the tailgate lid hand grip.
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
  7. Remove the tailgate lid lower trim (A) after removing the screws.
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Tailgate / Tailgate Lid Trim / Removal and Installation / Removal illustration
Tailgate Lid Side Trim Tailgate Lid Lower Trim

Installation

  1. Install in reverse order of removal.

Tailgate Assembly Removal and Installation

Removal

  1. Remove the tailgate lid trim. (Refer to Tailgate - "Tailgate Lid Trim")
  2. Remove the tailgate lift (A) after removing the clips (B).
    Body (Interior and Exterior) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration
  3. Disconnect connectors and wiring (A).
    Body (Interior and Exterior) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration
  4. Remove the tailgate assembly (A) after removing the bolts.

    Tightening torque : 7.8 - 11,8 N·m

    Body (Interior and Exterior) — Tailgate / Tailgate Assembly / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Tailgate Latch Removal and Installation

Removal

  1. Remove the tailgate lid lower trim. (Refer to Tailgate - "Tailgate Lid Trim")
  2. Disconnect the tailgate latch connector (A).
    Body (Interior and Exterior) — Tailgate / Tailgate Latch / Removal and Installation / Removal illustration
  3. Remove the tailgate latch (A) after removing the bolts.
    Tightening torque Tailgate latch : 21.6 - 26 N·m Power tailgate latch : 21.6 - 32 N·m
    Body (Interior and Exterior) — Tailgate / Tailgate Latch / Removal and Installation / Removal illustration
    [Tailgate Latch]
    Body (Interior and Exterior) — Tailgate / Tailgate Latch / Removal and Installation / Removal illustration
    [Power Tailgate Latch]
    Body (Interior and Exterior) — Tailgate / Tailgate Latch / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Tailgate Lifter Removal and Installation

Removal

Information
Work with at least 2 people when removing the part.
  1. Remove the lifter (A) from the bracket after removing the clips (B).
    Body (Interior and Exterior) — Tailgate / Tailgate Lifter / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Tailgate Weatherstrip Removal and Installation

Removal

Note
Be careful not to get sealant on the body surface.
  1. Remove the tailgate weatherstrip (A).
    Body (Interior and Exterior) — Tailgate / Tailgate Weatherstrip / Removal and Installation / Removal illustration
    Note
    When installing, check the center marking line (B).

Installation

  1. Install in reverse order of removal.

Tailgate Outside Handle Removal and Installation

Removal

  1. Remove the tailgate lower garnish. (Refer to Body Side Molding - "Tailgate Garnish")
  2. Remove the tailgate handle switch (A) after removing screws.
    Body (Interior and Exterior) — Tailgate / Tailgate Outside Handle / Removal and Installation / Removal illustration
    Information
    If replacing the tailgate handle switch, replace the license plate lamp assembly (A).
    Body (Interior and Exterior) — Tailgate / Tailgate Outside Handle / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Power Tailgate Unit Removal and Installation

Removal

  1. Remove the luggage side trim [Driver's side]. (Refer to Tailgate Trim - "Luggage Side Trim")
  2. Disconnect the power tailgate module connectors (A).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Unit / Removal and Installation / Removal illustration
  3. Remove the power tailgate module (A) after removing the nuts.

    Tightening torque : 6.9 - 10,8 N·m

    Body (Interior and Exterior) — Tailgate / Power Tailgate Unit / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.
  2. Perform the order below with the KDS when replacing the power tailgate unit. (S/W Management → Power Tailgate → Power Tailgate Mode Configuration)
    Information
    Refer to the KDS screen for operating conditions and details.
  3. Perform power tailgate initialization according to the procedure below.
    1. Press the power tailgate switch and the outside handle switch simultaneously.
    2. After pressing for more than 3 seconds, confirm the beep.
    3. Manually close the power tailgate completely.

Power Tailgate Drive Unit Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the rear pillar trim. (Refer to Interior Trim - "Rear Pillar Trim")
  3. Disconnect the power tailgate drive unit connector (A).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Drive Unit / Removal and Installation / Removal illustration
  4. Remove the power tailgate drive unit assembly (A) after removing the clips (B).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Drive Unit / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Power Tailgate Buzzer Removal and Installation

Removal

  1. Remove the tailgate lid lower trim. (Refer to Tailgate - "Tailgate Lid Trim")
  2. Remove the power tailgate buzzer (A) after disconnecting the connector (B).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Buzzer / Removal and Installation / Removal illustration
    Information
    Clip position :
    Body (Interior and Exterior) — Tailgate / Power Tailgate Buzzer / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Power Tailgate Switch Removal and Installation

Removal

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the power tailgate switch (A).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Switch / Removal and Installation / Removal illustration
  3. Disconnect the connector (A).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Switch / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Power Tailgate Strip Removal and Installation

Removal

  1. Remove the power tailgate strip (A).
    Body (Interior and Exterior) — Tailgate / Power Tailgate Strip / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.